flexfax: Phase D error

[Eric Smith <eric@fruitcom.com>]

Hi 

I am using the latest Beta HylaFAX from hylafax.org and a 

DAVICOM V.34+/FAX/VOICE/SPEAKERPHONE MODEM	 Ver:1.09I


I am getting the following error after an apparantly normal transmission:

Sep 15 08:36:04.93: [16290]: SEND begin page
Sep 15 08:36:04.93: [16290]: <-- data [1026]
Sep 15 08:36:04.93: [16290]: <-- data [1026]
Sep 15 08:36:04.93: [16290]: <-- data [1026]
Sep 15 08:36:04.93: [16290]: <-- data [1029]
Sep 15 08:36:04.93: [16290]: <-- data [1028]
Sep 15 08:36:06.90: [16290]: <-- data [1027]
Sep 15 08:36:06.90: [16290]: <-- data [1028]
Sep 15 08:36:06.90: [16290]: <-- data [1030]
Sep 15 08:36:08.87: [16290]: <-- data [1028]
Sep 15 08:36:08.87: [16290]: <-- data [1031]
Sep 15 08:36:08.87: [16290]: <-- data [1024]
Sep 15 08:36:08.87: [16290]: <-- data [1028]
Sep 15 08:36:10.85: [16290]: <-- data [1031]
Sep 15 08:36:10.85: [16290]: <-- data [1028]
Sep 15 08:36:10.85: [16290]: <-- data [1034]
Sep 15 08:36:10.85: [16290]: <-- data [1027]
Sep 15 08:36:12.82: [16290]: <-- data [1027]
Sep 15 08:36:12.82: [16290]: <-- data [1026]
Sep 15 08:36:12.82: [16290]: <-- data [1029]
Sep 15 08:36:14.79: [16290]: <-- data [1028]
Sep 15 08:36:14.79: [16290]: <-- data [1025]
Sep 15 08:36:14.79: [16290]: <-- data [1029]
Sep 15 08:36:14.79: [16290]: <-- data [1027]
Sep 15 08:36:16.76: [16290]: <-- data [1027]
Sep 15 08:36:16.76: [16290]: <-- data [1028]
Sep 15 08:36:16.76: [16290]: <-- data [372]
Sep 15 08:36:16.76: [16290]: SENT 25972 bytes of data
Sep 15 08:36:16.76: [16290]: <-- data [2]
Sep 15 08:36:16.76: [16290]: SEND end page
Sep 15 08:36:27.09: [16290]: --> [2:OK]
Sep 15 08:36:27.09: [16290]: SEND send EOP (no more pages or documents)
Sep 15 08:36:27.09: [16290]: <-- [9:AT+FET=2\r]
Sep 15 08:36:46.75: [16290]: --> [10:NO CARRIER]
Sep 15 08:36:46.75: [16290]: REMOTE HANGUP: Unspecified Transmit Phase D error, including
+FPHCTO timeout between data and +FET command (code 50)

Here is my config file:

# $Id: class2,v 1.2 1999/01/10 09:09:37 robert Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		1
AreaCode:		415
FAXNumber:		+1.999.555.1212
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"NothingSetup"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use this to supply a hint
#ModemRate:		19200		# max rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd:		AT+FCLASS=2	# command to enter class 2
Class2BORCmd:		AT+FBOR=0	# bit order for phase B/C/D (direct)
Class2RELCmd:		AT+FREL=1	# byte-align EOL codes on recv
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FK		# abort session command
Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FDCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FTBC=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FPHCTO=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBUG=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLID		# set local identifier command
Class2DCCCmd:		AT+FDCC		# set modem capabilities command
Class2DISCmd:		AT+FDIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FCIG		# set polling identifier command
Class2PTSCmd:		AT+FPTS		# set post-page status command
Class2SPLCmd:		AT+FSPL		# set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger:	""		# character sent to modem to start recv
#Class2XmitWaitForXON:	yes		# if true, wait for XON before send
#Class2XmitWaitForXON:	yes		# if true, wait for XON before send changed 15 Sept to no
Class2XmitWaitForXON:	no		# if true, wait for XON before send
-- 
Eric Smith
eric@fruitcom.com

perl is to programming what the haiku is to prose