flexfax: USR prof msg + REMOTE HANGUP: RSPREC error/got DCN (code 51)

[Michael Parker <nc-parkermi@netcologne.de>]

Hallo,

I=B4m using HylaFAX, Version 4.0 (release).

When I try to send a fax I receive the following error messages:

=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D

Your facsimile job to 0231513453 was not sent because:
>     RSPREC error/got DCN

> The job will be retried at 16:02.

>     ---- Transcript of session follows ----

> Jul 29 15:56:28.78: [  302]: SESSION BEGIN 00000003 49231513453
> Jul 29 15:56:28.79: [  302]: SEND FAX: JOB 2 DEST 0231513453
COMMID=20
00000003
> Jul 29 15:56:28.79: [  302]: MODEM set DTR OFF
> Jul 29 15:56:28.79: [  302]: DELAY 2600 ms
> Jul 29 15:56:31.38: [  302]: MODEM set DTR ON
> Jul 29 15:56:31.38: [  302]: MODEM set baud rate: 38400 baud,
input=20
flow RTS/CTS, output flow RTS/CTS
> Jul 29 15:56:31.38: [  302]: MODEM flush i/o
> Jul 29 15:56:31.38: [  302]: <-- [17:ATE0V1Q0X4S0=3D0H0\r]
> Jul 29 15:56:31.52: [  302]: --> [2:OK]
> Jul 29 15:56:31.52: [  302]: <--
[27:ATS8=3D2S7=3D60&H1&I0&R2&D2&C1\r]
> Jul 29 15:56:31.65: [  302]: --> [2:OK]
> Jul 29 15:56:31.65: [  302]: <-- [14:AT+FCLASS=3D2.0\r]
> Jul 29 15:56:31.78: [  302]: --> [2:OK]
> Jul 29 15:56:31.78: [  302]: <-- [9:AT+FLO=3D2\r]
> Jul 29 15:56:31.91: [  302]: --> [2:OK]
> Jul 29 15:56:31.91: [  302]: <-- [9:AT+FPP=3D0\r]
> Jul 29 15:56:32.04: [  302]: --> [2:OK]
> Jul 29 15:56:32.04: [  302]: <-- [9:AT+FBO=3D0\r]
> Jul 29 15:56:32.17: [  302]: --> [2:OK]
> Jul 29 15:56:32.17: [  302]: <-- [10:AT+FCT=3D30\r]
> Jul 29 15:56:32.30: [  302]: --> [2:OK]
> Jul 29 15:56:32.30: [  302]: <-- [15:AT+FNR=3D1,1,1,1\r]
> Jul 29 15:56:32.43: [  302]: --> [2:OK]
> Jul 29 15:56:32.43: [  302]: <-- [9:AT+FIE=3D0\r]
> Jul 29 15:56:32.56: [  302]: --> [2:OK]
> Jul 29 15:56:32.56: [  302]: <-- [23:AT+FCC=3D1,5,2,2,0,0,0,0\r]
> Jul 29 15:56:32.69: [  302]: --> [2:OK]
> Jul 29 15:56:32.69: [  302]: <-- [5:ATM0\r]
> Jul 29 15:56:32.82: [  302]: --> [2:OK]
> Jul 29 15:56:32.82: [  302]: MODEM input buffering enabled
> Jul 29 15:56:32.82: [  302]: <-- [14:AT+FCLASS=3D2.0\r]
> Jul 29 15:56:33.05: [  302]: --> [2:OK]
> Jul 29 15:56:33.05: [  302]: <-- [9:AT+FLO=3D2\r]
> Jul 29 15:56:33.28: [  302]: --> [2:OK]
> Jul 29 15:56:33.28: [  302]: <-- [9:AT+FPP=3D0\r]
> Jul 29 15:56:33.51: [  302]: --> [2:OK]
> Jul 29 15:56:33.51: [  302]: <-- [9:AT+FBO=3D0\r]
> Jul 29 15:56:33.74: [  302]: --> [2:OK]
> Jul 29 15:56:33.74: [  302]: <-- [10:AT+FCT=3D30\r]
> Jul 29 15:56:33.97: [  302]: --> [2:OK]
> Jul 29 15:56:33.97: [  302]: <-- [15:AT+FNR=3D1,1,1,1\r]
> Jul 29 15:56:34.20: [  302]: --> [2:OK]
> Jul 29 15:56:34.20: [  302]: <-- [9:AT+FIE=3D0\r]
> Jul 29 15:56:34.43: [  302]: --> [2:OK]
> Jul 29 15:56:34.43: [  302]: <-- [23:AT+FCC=3D1,5,2,2,0,0,0,0\r]
> Jul 29 15:56:34.66: [  302]: --> [2:OK]
> Jul 29 15:56:34.66: [  302]: <-- [30:AT+FLI=3D"Katharina Cordes &
M"\r]
> Jul 29 15:56:34.90: [  302]: --> [2:OK]
> Jul 29 15:56:34.92: [  302]: DIAL 0231513453
> Jul 29 15:56:34.92: [  302]: <-- [15:ATDT0231513453\r]
> Jul 29 15:57:06.84: [  302]: --> [4:+FCO]
> Jul 29 15:57:09.54: [  302]: --> [10:+FNF:P?:=02 ]
> Jul 29 15:57:09.54: [  302]: REMOTE NSF "P?:=02"
> Jul 29 15:57:09.54: [  302]: --> [27:+FCI:"
513453"]
> Jul 29 15:57:09.54: [  302]: REMOTE CSI "513453"
> Jul 29 15:57:09.54: [  302]: --> [20:+FIS:1,3,0,2,1,0,0,4]
> Jul 29 15:57:09.54: [  302]: --> [2:OK]
> Jul 29 15:57:09.54: [  302]: REMOTE best rate 9600 bit/s
> Jul 29 15:57:09.54: [  302]: REMOTE max page width 1728 pixels
in 215=20
mm
> Jul 29 15:57:09.54: [  302]: REMOTE max unlimited page length
> Jul 29 15:57:09.54: [  302]: REMOTE best vres 7.7 line/mm
> Jul 29 15:57:09.54: [  302]: REMOTE best format 2-D MR
> Jul 29 15:57:09.54: [  302]: REMOTE best 20 ms, 10 ms/scanline
> Jul 29 15:57:09.54: [  302]: USE 9600 bit/s
> Jul 29 15:57:09.54: [  302]: USE 20 ms, 10 ms/scanline
> Jul 29 15:57:09.54: [  302]: SEND file "docq/doc3.ps;00"
> Jul 29 15:57:09.54: [  302]: USE page width 1728 pixels in 215
mm
> Jul 29 15:57:09.54: [  302]: USE unlimited page length
> Jul 29 15:57:09.54: [  302]: USE 3.85 line/mm
> Jul 29 15:57:09.54: [  302]: USE 1-D MR
> Jul 29 15:57:09.54: [  302]: <-- [23:AT+FIS=3D0,3,0,2,0,0,0,4\r]
> Jul 29 15:57:09.78: [  302]: --> [2:OK]
> Jul 29 15:57:09.78: [  302]: <-- [7:AT+FDT\r]
> Jul 29 15:57:10.05: [  302]: --> [20:+FCS:0,3,0,2,0,0,0,4]
> Jul 29 15:57:15.63: [  302]: --> [7:CONNECT]
> Jul 29 15:57:15.63: [  302]: SEND begin page
> Jul 29 15:57:35.65: [  302]: SENT 22955 bytes of data
> Jul 29 15:57:35.65: [  302]: SEND 1D RTC
> Jul 29 15:57:35.65: [  302]: SEND end page
> Jul 29 15:57:35.65: [  302]: SEND send EOP (no more pages or documents)
> Jul 29 15:57:49.00: [  302]: --> [7:+FHS:51]
> Jul 29 15:57:49.00: [  302]: REMOTE HANGUP: RSPREC error/got DCN (code =
51)
> Jul 29 15:57:49.00: [  302]: <-- [5:ATH0\r]
> Jul 29 15:57:49.12: [  302]: --> [2:OK]
> Jul 29 15:57:49.12: [  302]: MODEM set DTR OFF
> Jul 29 15:57:49.12: [  302]: SESSION END

=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D

My config.modem actually looks like this:

[...]
RingsBeforeAnswer:	5
[...]
ModemType:		Class2.0	# use this to supply a hint
ModemRate:		38400		# max rate for DCE-DTE communication
ModemFlowControl:	rtscts		# XON/XOFF flow control assumed
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)

ModemDialCmd:		ATDT%s		# T for tone dialing, @ for silence
ModemResetCmds:		""		# stuff to do when modem is reset
ModemAnswerCmd:		ATA		# use this to answer phone
ModemNoFlowCmd:		AT&HO&I0&R1	# disable flow control cmd
ModemHardFlowCmd:	AT&H1&I0&R2	# hardware flow control cmd
ModemSoftFlowCmd:	AT&H2&I2&R1	# software flow control cmd
ModemNoAutoAnswerCmd:	ATS0=3D0		# disable auto-answer
ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:	ATE0		# disable command echo
ModemVerboseResultsCmd:	ATV1		# enable verbose command results
ModemResultCodesCmd:	ATQ0X4		# enable result codes
ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
ModemSoftResetCmd:	ATZ		# do soft reset of modem
ModemWaitTimeCmd:	ATS7=3D60		# wait 60 seconds for carrier
ModemCommaPauseTimeCmd:	ATS8=3D2		# comma pause time is 2 seconds
ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
Class2Cmd:		AT+FCLASS=3D2.0	# command to enter class 2.0
Class2BORCmd:		AT+FBO=3D0	# bit order for phase B/C/D (direct)
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FKS		# abort session command
Class2CQQueryCmd:	AT+FCQ=3D?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FCC=3D?	# query for modem capabilities
Class2TBCCmd:		AT+FPP=3D0	# setup stream mode
Class2CRCmd:		AT+FCR=3D1	# enable capability to receive
Class2PHCTOCmd:		AT+FCT=3D30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBU=3D1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLI		# set local identifier command
Class2DCCCmd:		AT+FCC		# set modem capabilities command
Class2DISCmd:		AT+FIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FPI		# set polling identifier command
Class2NRCmd:		AT+FNR=3D1,1,1,0	# setup status reporting command
Class2PIECmd:		AT+FIE=3D0	# disable interrupt-enable command
Class2PTSCmd:		AT+FPS		# set post-page status command
Class2SPLCmd:		AT+FSP		# set polling indicator command
Class2NFLOCmd:		AT+FLO=3D0	# set no flow control command
Class2SFLOCmd:		AT+FLO=3D1	# set software flow control command
Class2HFLOCmd:		AT+FLO=3D2	# set hardware flow control command

=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D


Any suggestions would be greatly appreciated !

Regards,
Michael