flexfax: Sendfax and FritzFax from AVM

[Dominik Roettsches <webmaster@bvppt.de>]

Hi there,

I get the error "NO ANSWER" from remote when connecting to the german "FRITZ
Fax" Sotware. This is an ISDN emulation for receiving analog faxes. It
normally should act as a real fax-machine but I have problems connecting to
it.
For me it seems, that the mentioned software - when dialing has been
performed - with the normal continoous beep-signal and so the hylafax
software does not start transmitting.
Does anybody now, how I can initiate transmitting a fax without waiting for
this tone?
Which Modem parameters have to be set?

I'm using an EXAR Modem with Rockwell 1414E Chipset as it is detected by
Hylafax.
Session log as follows:

Jul 11 13:13:23.24: [28536]: SESSION BEGIN 00000084 492151796761
Jul 11 13:13:23.24: [28536]: SEND FAX: JOB 55 DEST 796761 COMMID 00000084
Jul 11 13:13:23.24: [28536]: DELAY 2600 ms
Jul 11 13:13:25.86: [28536]: <-- [15:ATE0V1Q0S0=0H0\r]
Jul 11 13:13:26.46: [28536]: --> [2:OK]
Jul 11 13:13:26.46: [28536]: <-- [30:ATS8=2S7=80&S1\G0\Q4\X1&D2&C1\r]
Jul 11 13:13:26.71: [28536]: --> [2:OK]
Jul 11 13:13:26.71: [28536]: <-- [12:AT+FCLASS=2\r]
Jul 11 13:13:26.95: [28536]: --> [2:OK]
Jul 11 13:13:26.95: [28536]: <-- [10:AT+FTBC=0\r]
Jul 11 13:13:27.19: [28536]: --> [5:ERROR]
Jul 11 13:13:27.19: [28536]: MODEM Command error
Jul 11 13:13:27.19: [28536]: <-- [10:AT+FBOR=0\r]
Jul 11 13:13:27.43: [28536]: --> [2:OK]
Jul 11 13:13:27.43: [28536]: <-- [13:AT+FPHCTO=30\r]
Jul 11 13:13:27.67: [28536]: --> [5:ERROR]
Jul 11 13:13:27.67: [28536]: MODEM Command error
Jul 11 13:13:27.67: [28536]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Jul 11 13:13:27.91: [28536]: --> [2:OK]
Jul 11 13:13:27.91: [28536]: <-- [7:ATL2M1\r]
Jul 11 13:13:28.14: [28536]: --> [2:OK]
Jul 11 13:13:28.15: [28536]: <-- [12:AT+FCLASS=2\r]
Jul 11 13:13:28.48: [28536]: --> [2:OK]
Jul 11 13:13:28.48: [28536]: <-- [10:AT+FTBC=0\r]
Jul 11 13:13:28.82: [28536]: --> [5:ERROR]
Jul 11 13:13:28.82: [28536]: MODEM Command error
Jul 11 13:13:28.82: [28536]: <-- [10:AT+FBOR=0\r]
Jul 11 13:13:29.16: [28536]: --> [2:OK]
Jul 11 13:13:29.16: [28536]: <-- [13:AT+FPHCTO=30\r]
Jul 11 13:13:29.50: [28536]: --> [5:ERROR]
Jul 11 13:13:29.50: [28536]: MODEM Command error
Jul 11 13:13:29.50: [28536]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Jul 11 13:13:29.84: [28536]: --> [2:OK]
Jul 11 13:13:29.84: [28536]: <-- [26:AT+FLID="+49 2151 702160"\r]
Jul 11 13:13:30.18: [28536]: --> [2:OK]
Jul 11 13:13:30.18: [28536]: <-- [24:AT+FDIS=0,5,0,2,0,0,0,0\r]
Jul 11 13:13:30.52: [28536]: --> [2:OK]
Jul 11 13:13:30.53: [28536]: DIAL 796761
Jul 11 13:13:30.53: [28536]: <-- [12:ATDT796761@\r]
Jul 11 13:14:54.32: [28536]: --> [9:NO ANSWER]
Jul 11 13:14:54.35: [28536]: SEND FAILED: No answer from remote
Jul 11 13:14:54.35: [28536]: <-- [5:ATH0\r]
Jul 11 13:14:59.34: [28536]: MODEM <Timeout>
Jul 11 13:14:59.38: [28536]: SESSION END

Any help would be appreciated.

Thanks in advance

Dominik Roettsches
e-mail: D.Roettsches@bigfoot.com
see also: http://privat.schlund.de/dr/
ICQ: 1570287