 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: Missing EOL after 5 seconds. PLEASE HELP !!!!!!!! (with log)
- To: flexfax@sgi.com
- Subject: flexfax: Re: Missing EOL after 5 seconds. PLEASE HELP !!!!!!!! (with log)
- From: Levente Janovszki <levi@goliath.bmk.hu>
- cc: david@djwhome.demon.co.uk
- Date: Sat, 26 Jun 1999 17:41:20 +0200 (CEST)
>>=20
>> Hello !
>>=20
>> Please somebody help me !!!! I have been trying to set up Hyla for 3
days
>> !!
>> I use a Linux 2.0.36, E-tech Bullet E1414MX modem on cua1 and cannot
get
>
>What version of Linux, kernel versions are largely irrelevant compared
>with the distribution. What is this modem really; very few people make
>the underlying hardware for modems, but 100s of people stick their name
on
>the front.
>
Package: Hylafax 4.0pl2
Distribution: Red Hat Linux release 5.1 (Manhattan)
Kernel: Kernel 2.0.36 on an i586
Modem: E-TECH, Model No.: BULLET MODEM E1414MX/DX, external=20
H/W: B.1
F/W: V2.12
( it's an ancient modem :-)))))) )
=20
I use cua0 for send and cua1 for receive fax. ( with two same vendor, type
fax )
Sorry for my long letter.
( more comments in the message body please read that too. Thax. )=20
>> Jun 24 21:08:03.92: [ 5743]: MODEM set XON/XOFF/FLUSH: input ignored,
>> output generated
>> Jun 24 21:08:03.92: [ 5743]: RECV: send trigger 022
>> Jun 24 21:08:03.92: [ 5743]: <-- data [1]
>> Jun 24 21:09:10.56: [ 5743]: MODEM TIMEOUT: reading from modem
>> Jun 24 21:09:10.56: [ 5743]: <-- data [1]
>> Jun 24 21:09:10.56: [ 5743]: RECV: Missing EOL after 5 seconds
>
>Best guess is that this is the wrong trigger character, but 021 would
>tend to conflict with the software flow control that you have
>configured.
I have succeded once but no more. I cannot repeate it. What is the
problem???
-----------SENDING SESSION LOG cua0
Jun 24 20:08:25.93: [ 2696]: SESSION BEGIN 00000010 36182168
Jun 24 20:08:25.93: [ 2696]: SEND FAX: JOB 4 DEST 82,168 COMMID 00000010
Jun 24 20:08:25.93: [ 2696]: MODEM set DTR OFF
Jun 24 20:08:25.93: [ 2696]: DELAY 2600 ms
Jun 24 20:08:28.54: [ 2696]: MODEM set DTR ON
Jun 24 20:08:28.54: [ 2696]: MODEM set baud rate: 19200 baud, input flow
XON/XOFF, output flow XON/XOFF
Jun 24 20:08:28.54: [ 2696]: MODEM flush i/o
Jun 24 20:08:28.54: [ 2696]: <-- [15:ATE0V1Q0S0=3D0H0\r]
Jun 24 20:08:28.66: [ 2696]: --> [2:OK]
Jun 24 20:08:28.66: [ 2696]: <-- [21:ATS8=3D2S7=3D60$F0&D2&C1\r]
Jun 24 20:08:28.78: [ 2696]: --> [2:OK]
Jun 24 20:08:28.78: [ 2696]: <-- [12:AT+FCLASS=3D2\r]
Jun 24 20:08:28.90: [ 2696]: --> [2:OK]
Jun 24 20:08:28.90: [ 2696]: <-- [10:AT+FTBC=3D0\r]
Jun 24 20:08:29.02: [ 2696]: --> [5:ERROR]
Jun 24 20:08:29.02: [ 2696]: MODEM Command error
Jun 24 20:08:29.02: [ 2696]: <-- [10:AT+FBOR=3D0\r]
Jun 24 20:08:29.14: [ 2696]: --> [2:OK]
Jun 24 20:08:29.14: [ 2696]: <-- [13:AT+FPHCTO=3D30\r]
Jun 24 20:08:29.26: [ 2696]: --> [2:OK]
Jun 24 20:08:29.26: [ 2696]: <-- [10:AT+FBUG=3D1\r]
Jun 24 20:08:29.38: [ 2696]: --> [5:ERROR]
Jun 24 20:08:29.38: [ 2696]: MODEM Command error
Jun 24 20:08:29.38: [ 2696]: <-- [24:AT+FDCC=3D1,5,2,2,0,0,0,0\r]
Jun 24 20:08:29.51: [ 2696]: --> [2:OK]
Jun 24 20:08:29.51: [ 2696]: <-- [7:ATL1M1\r]
Jun 24 20:08:29.63: [ 2696]: --> [2:OK]
Jun 24 20:08:29.63: [ 2696]: STATE CHANGE: RUNNING -> SENDING
Jun 24 20:08:29.63: [ 2696]: MODEM input buffering enabled
Jun 24 20:08:29.63: [ 2696]: <-- [12:AT+FCLASS=3D2\r]
Jun 24 20:08:29.85: [ 2696]: --> [2:OK]
Jun 24 20:08:29.85: [ 2696]: <-- [10:AT+FTBC=3D0\r]
Jun 24 20:08:30.07: [ 2696]: --> [5:ERROR]
Jun 24 20:08:30.07: [ 2696]: MODEM Command error
Jun 24 20:08:30.07: [ 2696]: <-- [10:AT+FBOR=3D0\r]
Jun 24 20:08:30.29: [ 2696]: --> [2:OK]
Jun 24 20:08:30.29: [ 2696]: <-- [13:AT+FPHCTO=3D30\r]
Jun 24 20:08:30.51: [ 2696]: --> [2:OK]
Jun 24 20:08:30.51: [ 2696]: <-- [10:AT+FBUG=3D1\r]
Jun 24 20:08:30.73: [ 2696]: --> [5:ERROR]
Jun 24 20:08:30.73: [ 2696]: MODEM Command error
Jun 24 20:08:30.73: [ 2696]: <-- [24:AT+FDCC=3D1,5,2,2,0,0,0,0\r]
Jun 24 20:08:30.96: [ 2696]: --> [2:OK]
Jun 24 20:08:30.96: [ 2696]: <-- [28:AT+FLID=3D"SZTAKI fax server"\r]
Jun 24 20:08:31.19: [ 2696]: --> [2:OK]
Jun 24 20:08:31.19: [ 2696]: <-- [24:AT+FDIS=3D1,5,0,0,0,0,0,0\r]
Jun 24 20:08:31.42: [ 2696]: --> [2:OK]
Jun 24 20:08:31.43: [ 2696]: DIAL 82,168
Jun 24 20:08:31.43: [ 2696]: <-- [11:ATDP82,168\r]
Jun 24 20:08:44.58: [ 2696]: --> [3:CED]
Jun 24 20:08:49.65: [ 2696]: --> [5:+FCON]
Jun 24 20:08:49.65: [ 2696]: --> [29:+FCSI: " Incoming SZTAKI fax"]
Jun 24 20:08:49.65: [ 2696]: REMOTE CSI "Incoming SZTAKI fax"
Jun 24 20:08:49.65: [ 2696]: --> [22:+FDIS: 1,5,0,0,0,1,0,0]
Jun 24 20:08:49.65: [ 2696]: --> [2:OK]
Jun 24 20:08:49.65: [ 2696]: REMOTE best rate 14400 bit/s
Jun 24 20:08:49.65: [ 2696]: REMOTE max page width 1728 pixels in 215 mm
Jun 24 20:08:49.65: [ 2696]: REMOTE max A4 page length (297 mm)
Jun 24 20:08:49.65: [ 2696]: REMOTE best vres 7.7 line/mm
Jun 24 20:08:49.65: [ 2696]: REMOTE best format 1-D MR
Jun 24 20:08:49.65: [ 2696]: REMOTE supports T.30 Annex A, ECM
Jun 24 20:08:49.65: [ 2696]: REMOTE best 0 ms/scanline
Jun 24 20:08:49.65: [ 2696]: USE 14400 bit/s
Jun 24 20:08:49.65: [ 2696]: USE 0 ms/scanline
Jun 24 20:08:49.65: [ 2696]: SEND file "docq/doc4.ps;31"
Jun 24 20:08:49.65: [ 2696]: USE page width 1728 pixels in 215 mm
Jun 24 20:08:49.65: [ 2696]: USE A4 page length (297 mm)
Jun 24 20:08:49.65: [ 2696]: USE 7.7 line/mm
Jun 24 20:08:49.65: [ 2696]: USE 1-D MR
Jun 24 20:08:49.65: [ 2696]: MODEM set XON/XOFF/NOW: input ignored, output
generated
Jun 24 20:08:49.65: [ 2696]: <-- [7:AT+FDT\r]
Jun 24 20:08:59.29: [ 2696]: --> [22:+FDCS: 1,5,0,0,0,0,0,0]
Jun 24 20:08:59.96: [ 2696]: --> [7:CONNECT]
Jun 24 20:08:59.96: [ 2696]: SEND wait for XON
Jun 24 20:08:59.96: [ 2696]: --> [1:^Q]
Jun 24 20:08:59.96: [ 2696]: MODEM set XON/XOFF/NOW: input interpreted,
output generated
Jun 24 20:08:59.96: [ 2696]: SEND begin page
Jun 24 20:08:59.96: [ 2696]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Jun 24 20:09:00.00: [ 2696]: <-- data [1033]
Jun 24 20:09:00.00: [ 2696]: <-- data [1030]
Jun 24 20:09:00.00: [ 2696]: <-- data [1033]
Jun 24 20:09:00.00: [ 2696]: <-- data [1027]
Jun 24 20:09:01.99: [ 2696]: <-- data [1032]
Jun 24 20:09:01.99: [ 2696]: <-- data [1025]
Jun 24 20:09:01.99: [ 2696]: <-- data [1024]
Jun 24 20:09:01.99: [ 2696]: <-- data [1024]
Jun 24 20:09:03.99: [ 2696]: <-- data [1024]
Jun 24 20:09:03.99: [ 2696]: <-- data [1024]
Jun 24 20:09:03.99: [ 2696]: <-- data [1024]
Jun 24 20:09:03.99: [ 2696]: <-- data [1024]
Jun 24 20:09:05.99: [ 2696]: <-- data [737]
Jun 24 20:09:05.99: [ 2696]: SENT 13025 bytes of data
Jun 24 20:09:05.99: [ 2696]: <-- data [2]
Jun 24 20:09:05.99: [ 2696]: MODEM set XON/XOFF/DRAIN: input interpreted,
output generated
Jun 24 20:09:06.78: [ 2696]: SEND end page
Jun 24 20:09:07.49: [ 2696]: --> [2:OK]
Jun 24 20:09:07.49: [ 2696]: SEND send EOP (no more pages or documents)
Jun 24 20:09:07.49: [ 2696]: <-- [9:AT+FET=3D2\r]
Jun 24 20:09:11.45: [ 2696]: --> [17:+FPTS: 1,2156,0,0]
Jun 24 20:09:11.45: [ 2696]: SEND recv MCF (message confirmation)
Jun 24 20:09:11.45: [ 2696]: SEND FAX (00000010): FROM
jlevente@ftest.aszi.sztaki.hu TO 82,168 (page 1 of 1 sent in 0:22)
Jun 24 20:09:11.45: [ 2696]: SEND FAX (00000010): FROM
jlevente@ftest.aszi.sztaki.hu TO 82,168 (docq/doc4.ps;31 sent in 0:22)
Jun 24 20:09:11.45: [ 2696]: <-- [5:ATH0\r]
Jun 24 20:09:12.93: [ 2696]: --> [8:+FHNG: 0]
Jun 24 20:09:12.93: [ 2696]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Jun 24 20:09:12.93: [ 2696]: --> [2:OK]
Jun 24 20:09:12.93: [ 2696]: MODEM set DTR OFF
Jun 24 20:09:12.93: [ 2696]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Jun 24 20:09:12.93: [ 2696]: SESSION END
-----------END SENDING SESSION LOG
-----------RECEIVING SESSION LOG cua1
Jun 24 20:08:42.62: [25619]: SESSION BEGIN 00000011 3613497986
Jun 24 20:08:42.62: [25619]: <-- [4:ATA\r]
Jun 24 20:08:52.70: [25619]: --> [5:+FCON]
Jun 24 20:08:52.70: [25619]: MODEM set baud rate: 19200 baud (flow control
unchanged)
Jun 24 20:08:52.70: [25619]: ANSWER: FAX CONNECTION
Jun 24 20:08:52.70: [25619]: STATE CHANGE: ANSWERING -> RECEIVING
Jun 24 20:08:52.70: [25619]: MODEM input buffering enabled
Jun 24 20:08:52.70: [25619]: RECV FAX: begin
Jun 24 20:08:57.41: [25619]: -->
[60:=E6~@~X~@~^~Fx~X`f~Xf~F~F~^F`~F`^F`^F`^F`=E6~X~F~^^Ff^F~X~^~X~F~X^Xx^F~=
^~@^F`=E6=F8fx^X~F~f~^^X~F`f~@~X~@]
Jun 24 20:08:57.41: [25619]: --> [22:+FDCS: 1,5,0,0,0,0,0,0]
Jun 24 20:08:57.41: [25619]: REMOTE wants 14400 bit/s
Jun 24 20:08:57.41: [25619]: REMOTE wants page width 1728 pixels in 215 mm
Jun 24 20:08:57.41: [25619]: REMOTE wants A4 page length (297 mm)
Jun 24 20:08:57.41: [25619]: REMOTE wants 7.7 line/mm
Jun 24 20:08:57.41: [25619]: REMOTE wants 1-D MR
Jun 24 20:08:57.41: [25619]: --> [2:OK]
Jun 24 20:08:57.41: [25619]: <-- [7:AT+FDR\r]
Jun 24 20:08:57.90: [25619]: --> [5:+FCFR]
Jun 24 20:08:59.90: [25619]: --> [7:CONNECT]
Jun 24 20:08:59.90: [25619]: RECV: begin page
Jun 24 20:08:59.90: [25619]: MODEM set XON/XOFF/FLUSH: input ignored,
output generated
Jun 24 20:08:59.90: [25619]: RECV: send trigger 022
Jun 24 20:08:59.90: [25619]: <-- data [1]Jun 24 20:09:07.50: [25619]:
RECV/CQ: Bad 1D pixel count, row 2156, got 0, expected 1728Jun 24
20:09:07.50: [25619]: RECV/CQ: Bad 1D pixel count, row 2157, got 0,
expected 1728
Jun 24 20:09:07.50: [25619]: RECV/CQ: Invalid WhiteTable code word, row
2158, x 0Jun 24 20:09:07.50: [25619]: RECV/CQ: Bad 1D pixel count, row
2158, got 0, expected 1728
Jun 24 20:09:07.50: [25619]: RECV/CQ: Adjusting for trailing noise (3 run)
Jun 24 20:09:07.50: [25619]: RECV: 2156 total lines, 0 bad lines, 0
consecutive bad lines
Jun 24 20:09:07.50: [25619]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Jun 24 20:09:09.09: [25619]: --> [17:+FPTS: 1,2156,0,0]
Jun 24 20:09:09.09: [25619]: --> [7:+FET: 2]
Jun 24 20:09:09.09: [25619]: RECV recv EOP (no more pages or documents)
Jun 24 20:09:09.09: [25619]: --> [2:OK]
Jun 24 20:09:09.09: [25619]: RECV send MCF (message confirmation)
Jun 24 20:09:09.09: [25619]: RECV FAX (00000011): from <UNSPECIFIED>, page
1 in 0:12, A4, 7.7 line/mm, 1-D MR
Jun 24 20:09:09.09: [25619]: RECV FAX (00000011): recvq/fax00005.tif from
<UNSPECIFIED>, route to <unspecified>, 1 pages in 0:17
Jun 24 20:09:09.16: [25619]: <-- [7:AT+FDR\r]
Jun 24 20:09:14.35: [25619]: --> [8:+FHNG: 0]
Jun 24 20:09:14.35: [25619]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Jun 24 20:09:14.35: [25619]: RECV FAX: bin/faxrcvd "recvq/fax00005.tif"
"cua1" "00000011" ""
Jun 24 20:09:17.29: [25619]: RECV FAX: end
Jun 24 20:09:17.29: [25619]: SESSION END
------------END RECEIVING SESSION LOG
The above session cannot be repeated any more with succes.
So I changed the trigger to 021 ( Hex 11, Dec 17 (DC1) wich is Control-Q
isn't it?)
Now I use the configs which you can find below. And I get the same logs
like at the end of my e-mail. It's interesting that the modem got hangup
!! And maybe you can see any relation in the time stamps!!!!!!.
------------SERVER CONFIG
LogFacility: local0
CountryCode: 36
AreaCode: 1
LongDistancePrefix: 9
InternationalPrefix: 011
DialStringRules: etc/dialrules
ModemClass: "out:cua0"
#ClocalAsRoot: yes
------------END SERVER CONFIG
------------CONFIG OF SENDING MODEM config.cua0
CountryCode: 36
AreaCode: 1
FAXNumber: "+36 1 349-7986"
LongDistancePrefix: 06
InternationalPrefix: 011
DialStringRules: etc/dialrules
# ServerTracing: 139
SessionTracing: 8191
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: Low
GettyArgs: "-h %l %s"
LocalIdentifier: "SZTAKI fax server"
LogFacility: local0
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
MaxRecvPages: 25
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use this to supply a hint
ModemRate: 19200 # max rate for DCE-DTE
communication
#ModemFlowControl: xonxoff # default
ModemFlowControl: rtscts # default
#
ModemSoftFlowCmd: AT$F0 # software XON/XOFF local flow
control
ModemHardFlowCmd: AT$F4 # hardware flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDP%s # T for tone dialing, @ for
silence
#
Class2DDISCmd: AT+FDIS # fix for resolution problems
Class2RecvDataTrigger: "\021" # DC2
#Class2CQCmd: "AT+FCQ=3D1;+FBADMUL=3D5;+FBADLIN=3D10"
#
#Class2RELCmd: ""
#ModemOnHookCmd: <waitfor:OK>
#ModemSendFillOrder: LSB2MSB
#ModemRecvFillOrder: MSB2LSB
Class2XmitWaitForXON: Yes
------------END OF CONFIG
------------CONFIG OF RECEIVING MODEM config.cua1
CountryCode: 36
AreaCode: 1
FAXNumber: "+36 1 349-7986"
LongDistancePrefix: 06
InternationalPrefix: 011
DialStringRules: etc/dialrules
#ServerTracing: 139
SessionTracing: 8191
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: Low
GettyArgs: "-h %l %s"
LocalIdentifier: "Incoming SZTAKI fax server"
LogFacility: local0
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
MaxRecvPages: 25
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use this to supply a hint
ModemRate: 19200 # max rate for DCE-DTE
communication
#ModemFlowControl: xonxoff # default
ModemFlowControl: rtscts # default
#
ModemSoftFlowCmd: AT$F0 # software XON/XOFF local flow
control
ModemHardFlowCmd: AT$F4 # hardware flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
ModemSetupAACmd: AT+FAA=3D1
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDP%s # T for tone dialing, @ for
silence
#
Class2DDISCmd: AT+FDIS # fix for resolution problems
Class2RecvDataTrigger: "\021" # DC2
#Class2REVCmd: ""
ModemOnHookCmd: <waitfor:OK>
#ModemAnswerFaxBeginCmd: "<19200><xon>"
#ModemRecvFillOrder: MSB2LSB
#ModemSendFillOrder: LSB2MSB
ModemXmitWaitForXON: Yes
------------END OF CONFIG
------------FAILED SESSIONS (SENDING)
Jun 25 14:28:20.00: [15368]: SESSION BEGIN 00000016 36182168
Jun 25 14:28:20.00: [15368]: SEND FAX: JOB 12 DEST 82,168 COMMID 00000016
Jun 25 14:28:20.00: [15368]: MODEM set DTR OFF
Jun 25 14:28:20.00: [15368]: DELAY 2600 ms
Jun 25 14:28:22.61: [15368]: MODEM set DTR ON
Jun 25 14:28:22.61: [15368]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Jun 25 14:28:22.61: [15368]: MODEM flush i/o
Jun 25 14:28:22.61: [15368]: <-- [15:ATE0V1Q0S0=3D0H0\r]
Jun 25 14:28:22.73: [15368]: --> [2:OK]
Jun 25 14:28:22.73: [15368]: <-- [21:ATS8=3D2S7=3D60$F4&D2&C1\r]
Jun 25 14:28:22.86: [15368]: --> [2:OK]
Jun 25 14:28:22.86: [15368]: <-- [12:AT+FCLASS=3D2\r]
Jun 25 14:28:22.98: [15368]: --> [2:OK]
Jun 25 14:28:22.98: [15368]: <-- [10:AT+FTBC=3D0\r]
Jun 25 14:28:23.10: [15368]: --> [5:ERROR]
Jun 25 14:28:23.10: [15368]: MODEM Command error
Jun 25 14:28:23.10: [15368]: <-- [10:AT+FBOR=3D0\r]
Jun 25 14:28:23.22: [15368]: --> [2:OK]
Jun 25 14:28:23.22: [15368]: <-- [13:AT+FPHCTO=3D30\r]
Jun 25 14:28:23.34: [15368]: --> [2:OK]
Jun 25 14:28:23.34: [15368]: <-- [10:AT+FBUG=3D1\r]
Jun 25 14:28:23.46: [15368]: --> [5:ERROR]
Jun 25 14:28:23.46: [15368]: MODEM Command error
Jun 25 14:28:23.46: [15368]: <-- [24:AT+FDCC=3D1,5,2,2,0,0,0,0\r]
Jun 25 14:28:23.59: [15368]: --> [2:OK]
Jun 25 14:28:23.59: [15368]: <-- [7:ATL1M1\r]
Jun 25 14:28:23.71: [15368]: --> [2:OK]
Jun 25 14:28:23.71: [15368]: STATE CHANGE: RUNNING -> SENDING
Jun 25 14:28:23.71: [15368]: MODEM input buffering enabled
Jun 25 14:28:23.71: [15368]: <-- [12:AT+FCLASS=3D2\r]
Jun 25 14:28:23.93: [15368]: --> [2:OK]
Jun 25 14:28:23.93: [15368]: <-- [10:AT+FTBC=3D0\r]
Jun 25 14:28:24.15: [15368]: --> [5:ERROR]
Jun 25 14:28:24.15: [15368]: MODEM Command error
Jun 25 14:28:24.15: [15368]: <-- [10:AT+FBOR=3D0\r]
Jun 25 14:28:24.37: [15368]: --> [2:OK]
Jun 25 14:28:24.37: [15368]: <-- [13:AT+FPHCTO=3D30\r]
Jun 25 14:28:24.59: [15368]: --> [2:OK]
Jun 25 14:28:24.59: [15368]: <-- [10:AT+FBUG=3D1\r]
Jun 25 14:28:24.81: [15368]: --> [5:ERROR]
Jun 25 14:28:24.81: [15368]: MODEM Command error
Jun 25 14:28:24.81: [15368]: <-- [24:AT+FDCC=3D1,5,2,2,0,0,0,0\r]
Jun 25 14:28:25.04: [15368]: --> [2:OK]
Jun 25 14:28:25.04: [15368]: <-- [28:AT+FLID=3D"SZTAKI fax server"\r]
Jun 25 14:28:25.27: [15368]: --> [2:OK]
Jun 25 14:28:25.27: [15368]: <-- [24:AT+FDIS=3D1,5,0,0,0,0,0,0\r]
Jun 25 14:28:25.50: [15368]: --> [2:OK]
Jun 25 14:28:25.52: [15368]: DIAL 82,168
Jun 25 14:28:25.52: [15368]: <-- [11:ATDP82,168\r]
Jun 25 14:28:38.78: [15368]: --> [3:CED]
Jun 25 14:28:43.82: [15368]: --> [5:+FCON]
Jun 25 14:28:43.82: [15368]: --> [29:+FCSI: " Incoming SZTAKI fax"]
Jun 25 14:28:43.82: [15368]: REMOTE CSI "Incoming SZTAKI fax"
Jun 25 14:28:43.82: [15368]: --> [22:+FDIS: 1,5,0,0,0,1,0,0]
Jun 25 14:28:43.82: [15368]: --> [2:OK]
Jun 25 14:28:43.82: [15368]: REMOTE best rate 14400 bit/s
Jun 25 14:28:43.82: [15368]: REMOTE max page width 1728 pixels in 215 mm
Jun 25 14:28:43.82: [15368]: REMOTE max A4 page length (297 mm)
Jun 25 14:28:43.82: [15368]: REMOTE best vres 7.7 line/mm
Jun 25 14:28:43.82: [15368]: REMOTE best format 1-D MR
Jun 25 14:28:43.82: [15368]: REMOTE supports T.30 Annex A, ECM
Jun 25 14:28:43.82: [15368]: REMOTE best 0 ms/scanline
Jun 25 14:28:43.82: [15368]: USE 14400 bit/s
Jun 25 14:28:43.82: [15368]: USE 0 ms/scanline
Jun 25 14:28:43.82: [15368]: SEND file "docq/doc12.ps;31"
Jun 25 14:28:43.90: [15368]: USE page width 1728 pixels in 215 mm
Jun 25 14:28:43.90: [15368]: USE A4 page length (297 mm)
Jun 25 14:28:43.90: [15368]: USE 7.7 line/mm
Jun 25 14:28:43.90: [15368]: USE 1-D MR
Jun 25 14:28:43.90: [15368]: <-- [7:AT+FDT\r]
Jun 25 14:28:53.44: [15368]: --> [22:+FDCS: 1,5,0,0,0,0,0,0]
Jun 25 14:28:54.11: [15368]: --> [7:CONNECT]
Jun 25 14:28:54.12: [15368]: SEND wait for XON
Jun 25 14:28:54.12: [15368]: --> [1:^Q]
Jun 25 14:28:54.12: [15368]: SEND begin page
Jun 25 14:28:54.18: [15368]: <-- data [1030]
Jun 25 14:28:54.18: [15368]: <-- data [1027]
Jun 25 14:28:54.18: [15368]: <-- data [1025]
Jun 25 14:28:54.18: [15368]: <-- data [1029]
Jun 25 14:28:54.18: [15368]: <-- data [1024]
Jun 25 14:28:56.17: [15368]: <-- data [1024]
Jun 25 14:28:56.17: [15368]: <-- data [1024]
Jun 25 14:28:56.17: [15368]: <-- data [1024]
Jun 25 14:28:58.17: [15368]: <-- data [1024]
Jun 25 14:28:58.17: [15368]: <-- data [1024]
Jun 25 14:28:58.17: [15368]: <-- data [1024]
Jun 25 14:28:58.17: [15368]: <-- data [264]
Jun 25 14:28:58.17: [15368]: SENT 11528 bytes of data
Jun 25 14:28:58.17: [15368]: <-- data [2]
Jun 25 14:28:58.17: [15368]: SEND end page
Jun 25 14:29:00.83: [15368]: --> [2:OK]
Jun 25 14:29:00.84: [15368]: SEND send EOP (no more pages or documents)
Jun 25 14:29:00.84: [15368]: <-- [9:AT+FET=3D2\r]
Jun 25 14:29:15.32: [15368]: --> [9:+FHNG: 30]
Jun 25 14:29:15.32: [15368]: REMOTE HANGUP: Unknown hangup code (code 30)
Jun 25 14:29:15.32: [15368]: <-- [5:ATH0\r]
Jun 25 14:29:15.33: [15368]: --> [2:OK]
Jun 25 14:29:15.33: [15368]: MODEM set DTR OFF
Jun 25 14:29:15.35: [15368]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Jun 25 14:29:15.35: [15368]: SESSION END
------------END OF SESSION
------------FAILED SESSIONS (RECEIVING)
Jun 25 14:28:36.81: [12744]: SESSION BEGIN 00000017 3613497986
Jun 25 14:28:36.81: [12744]: <-- [4:ATA\r]
Jun 25 14:28:46.87: [12744]: --> [5:+FCON]
Jun 25 14:28:46.87: [12744]: ANSWER: FAX CONNECTION
Jun 25 14:28:46.87: [12744]: STATE CHANGE: ANSWERING -> RECEIVING
Jun 25 14:28:46.87: [12744]: MODEM input buffering enabled
Jun 25 14:28:46.87: [12744]: RECV FAX: begin
Jun 25 14:28:51.57: [12744]: --> [29:+FTSI: " SZTAKI fax server"]
Jun 25 14:28:51.57: [12744]: REMOTE TSI "SZTAKI fax server"
Jun 25 14:28:51.57: [12744]: --> [22:+FDCS: 1,5,0,0,0,0,0,0]
Jun 25 14:28:51.57: [12744]: REMOTE wants 14400 bit/s
Jun 25 14:28:51.57: [12744]: REMOTE wants page width 1728 pixels in 215 mm
Jun 25 14:28:51.57: [12744]: REMOTE wants A4 page length (297 mm)
Jun 25 14:28:51.57: [12744]: REMOTE wants 7.7 line/mm
Jun 25 14:28:51.57: [12744]: REMOTE wants 1-D MR
Jun 25 14:28:51.57: [12744]: --> [2:OK]
Jun 25 14:28:51.57: [12744]: <-- [7:AT+FDR\r]
Jun 25 14:28:52.05: [12744]: --> [5:+FCFR]
Jun 25 14:28:54.05: [12744]: --> [7:CONNECT]
Jun 25 14:28:54.06: [12744]: RECV: begin page
Jun 25 14:28:54.06: [12744]: RECV: send trigger 021
Jun 25 14:28:54.06: [12744]: <-- data [1]
Jun 25 14:28:54.13: [12744]: RECV/CQ: Bad 1D pixel count, row 0, got 1990,
expected 1728
Jun 25 14:28:54.26: [12744]: RECV/CQ: Invalid WhiteTable code word, row 1,
x 45
Jun 25 14:28:54.27: [12744]: RECV/CQ: Bad 1D pixel count, row 1, got 45,
expected 1728
Jun 25 14:28:54.33: [12744]: RECV/CQ: Invalid WhiteTable code word, row 2,
x 42
Jun 25 14:28:54.34: [12744]: RECV/CQ: Bad 1D pixel count, row 2, got 42,
expected 1728
------- 8< -----
=2E..
Jun 25 14:29:14.84: [12744]: RECV/CQ: Bad 1D pixel count, row 39, got
2208, expected 1728
Jun 25 14:29:15.15: [12744]: RECV/CQ: Bad 1D pixel count, row 40, got
1820, expected 1728
Jun 25 14:29:17.04: [12744]: RECV/CQ: Adjusting for trailing noise (41
run)
Jun 25 14:29:17.04: [12744]: RECV: 0 total lines, 0 bad lines, 0
consecutive bad lines
Jun 25 14:29:30.64: [12744]: --> [8:+FHNG: 0]
Jun 25 14:29:30.64: [12744]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Jun 25 14:29:30.64: [12744]: --> [2:OK]
Jun 25 14:29:30.65: [12744]: RECV FAX (00000017): recvq/fax00015.tif from
SZTAKI fax server, route to <unspecified>, 0 pages in 0:44
Jun 25 14:29:30.65: [12744]: RECV FAX: Normal and proper end of connection
Jun 25 14:29:30.65: [12744]: RECV FAX (00000017): session with SZTAKI fax
server terminated abnormally: Normal and proper end of connection
Jun 25 14:29:30.65: [12744]: RECV FAX: bin/faxrcvd "recvq/fax00015.tif"
"cua1" "00000017" "Normal and proper end of connection"
Jun 25 14:29:32.31: [12744]: RECV FAX: end
------------END OF SESSIONS
That is my hyla history BUT I don't give up!
Thax for your help. Waiting for reply.
Regards
Levente
| Levente Janovszki | Bekes County Library JUST 4 lines 4 U |
| levi@athos.bmk.hu | Bekescsaba, Derkovits sor 1. HUNGARY Zip: 5600 |
| Linux. Just use it | * The operating system collapsed * | =20
| w/o fear of panic: | * OK Cancel * |=20
- Follow-Ups:
- Re: Re: Missing EOL after 5 seconds. PLEASE HELP !!!!!!!! (with log)
- From: David Woolley <david@djwhome.demon.co.uk>
- Re: Re: Missing EOL after 5 seconds. PLEASE HELP !!!!!!!! (with log)
- Prev by Date: +23.456.7890@faxmenow.com
- Next by Date: ELSA MikroLink[tm] Office or US-Robotics & Hylafax
- Prev by thread: Re: Missing EOL after 5 seconds. PLEASE HELP !!!!!!!! (with log)
- Next by thread: Re: Re: Missing EOL after 5 seconds. PLEASE HELP !!!!!!!! (with log)
- Index(es):
Project hosted by iFAX Solutions