Re: flexfax: faxaddmodem --> elsa microlink 56k

[Stephan Bauer <stephan_bauer@gmx.de>]

Hello,

I'm now using the Elsa microlink 56K basic.
I found a config file at the Elsa homepage and
changed it a bit.
Now I can send faxes to a faxmachine without 'retrain negativ' where
I had problems before.

Hope this helps

regards

Stephan

P.S. I think Elsa is a good choise

Michael Konopatzki schrieb:
> 
> I have some problems with faxaddmodem and the elsa microlink 56k pro.
> 
> The faxaddmodem-program recognizes only a class1 modem.
> 
> What can I do to let the faxaddmodem-programm recognize a
> class2 or class 2.0 modem or better the elsa microlink 56k pro ?
> 
> Some idea ?
> 
> Thanks for your help !!
> 
> My System is:
> SuSE Linux 6.0, Kernel 2.0.36
> Hylafax v4.0pl2-37
> Elsa Microlink 56k pro, Firmware: 1.59
> 
> --
> Mediadom audiovisuelle Medien GmbH
> Merheimer Str. 151
> 50733 K�ln
> - GERMANY -
> 
> Tel.: +49 (0) 221 / 917 11 80
> Fax.: +49 (0) 221 / 917 1181
> 
> email: kuno@mediadom.de
> internet: http://www.mediadom.de
#
# Class 2.0 modem configuration for ELSA 33.6 TQV.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            49
AreaCode:		7306
FAXNumber:		+49.7306.919594
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        "etc/dialrules"
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      2
SpeakerVolume:          quiet
GettyArgs:              "-h %l %s"
LocalIdentifier:        "Kling & Bauer"
#LogFacility:            local7
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "%%l|%c|Seite %%p von %%t"
PercentGoodLines:       80
MaxConsecutiveBadLines: 20
MaxRecvPages:           50
ModemPriority:          200
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use this to supply a hint
ModemRate:              115200          # max rate for DCE-DTE communication
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:           ATDT%s
#ModemDialCmd:		"ATX0\nATDT0%s"		# no '@' 'cuz then busy not recognized
ModemDialCmd:		"ATDT0%s"		# no '@' 'cuz then busy not recognized
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:         ATX3            # stuff to do when modem is reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT&K
ModemHardFlowCmd:       AT&K3
ModemSoftFlowCmd:       AT&K1
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results
ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH             # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)
Class2CQCmd:            ""              # commands to enable copy quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command