 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: Is there a solution to the "No response to MPS or EOP" problem?
- To: "Swoboda, Stefan (S.P.)" <sswoboda@ford.com>
- Subject: Re: flexfax: Is there a solution to the "No response to MPS or EOP" problem?
- From: Joaqu�n Arza Laurenz <jarza@unav.es>
- CC: "'flexfax@sgi.com'" <flexfax@sgi.com>
- Date: Mon, 10 May 1999 16:23:46 +0200
I have the same problem with my 3Com US Robotics 56K Voice Faxmodem. I tried every configuration I found on the list, and none of them were a solution. My server is working with only an old Rockwell card working at 28.800. The worst problem is that I can't buy any of the recomended modems in the list "www.hylafax.org/modems.php". If the 3Com modem is not working, perhaps it shouldn't be in the list. Good luck, Joaquin. "Swoboda, Stefan (S.P.)" wrote: > Hi there, > > I cannot offer a solution but I share the frustration of Phil since I can > reproduce this > exact problem with my setup: > > Hylafax 4.0pl2 binary distribution included in SuSE Linux 6.0 (Kernel > 2.0.36) > 3Com US Robotics 56K Voice Faxmodem > > This problem occurs reproducibly on certain analog fax machines. Even more > frustrating > is the fact that I did a cross check with the efax package. That worked ok > !!! > > So either this is a Hylafax bug or a driver problem. In either case it is > sure that it can be > done since efax can do it. My config.ttyS0 is basically based on the USR20 > template from > the config dirctory of the distribution with a small modification to get > across my PBX. > > Any help or comment is greatly appreciated. > > **************************************************************************** > ************ > Two examples of affected fax machines: > > Siemens FAX 940 > T Fax 382L > > **************************************************************************** > ************* > Transcript of failing fax transmissions: > > Facsimile transmitted since 04/29/99 23:25: > > Sender Pages Time Pg/min Errs TypRate TypData > stefan.swoboda@iteam.de 9 10:06 0.9 5 14400 1-D MR > --------------------------------------------------------------------- > Total 9 10:06 0.9 5 > > Facsimile transmitted since last week: > > Sender Pages Time Pg/min Errs TypRate TypData > root@silverwolf.iteam.de 8 2:54 2.8 0 9600 1-D MR > stefan.swoboda@iteam.de 12 10:53 1.1 5 14400 1-D MR > ---------------------------------------------------------------------- > Total 20 13:47 1.5 5 > > Facsimile received since 04/29/99 23:25: > > Sender Pages Time Pg/min Errs TypRate TypData > +49 2236 604 820 3 1:04 2.8 0 14400 1-D MR > ----------------------------------------------------------- > Total 3 1:04 2.8 0 > > Facsimile received since last week: > > Sender Pages Time Pg/min Errs TypRate TypData > +49 211 43 50 653 6 1:37 3.7 0 14400 1-D MR > +49 2236 604 820 3 1:04 2.8 0 14400 1-D MR > ------------------------------------------------------------ > Total 9 2:41 3.4 0 > > Report failed calls and associated session logs: > > To: stefan.swoboda@i Date: 04/30/99 20:25 > Error: Communication failure during Phase B/C > > ---- Transcript of session follows ---- > > Apr 30 20:25:09.51: [ 1392]: SESSION BEGIN 00000021 492236604820 > Apr 30 20:25:09.52: [ 1392]: SEND FAX: JOB 15 DEST 02236604820 COMMID > 00000021 > Apr 30 20:25:09.52: [ 1392]: MODEM set DTR OFF > Apr 30 20:25:09.52: [ 1392]: DELAY 2600 ms > Apr 30 20:25:12.12: [ 1392]: MODEM set DTR ON > Apr 30 20:25:12.12: [ 1392]: MODEM set baud rate: 19200 baud, input flow > RTS/CTS, output flow RTS/CTS > Apr 30 20:25:12.12: [ 1392]: MODEM flush i/o > Apr 30 20:25:12.12: [ 1392]: <-- [17:ATE0V1Q0X3S0=0H0\r] > Apr 30 20:25:12.27: [ 1392]: --> [2:OK] > Apr 30 20:25:12.27: [ 1392]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r] > Apr 30 20:25:12.42: [ 1392]: --> [2:OK] > Apr 30 20:25:12.42: [ 1392]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 20:25:12.56: [ 1392]: --> [2:OK] > Apr 30 20:25:12.56: [ 1392]: <-- [9:AT+FLO=2\r] > Apr 30 20:25:12.70: [ 1392]: --> [2:OK] > Apr 30 20:25:12.70: [ 1392]: <-- [9:AT+FPP=0\r] > Apr 30 20:25:12.84: [ 1392]: --> [2:OK] > Apr 30 20:25:12.84: [ 1392]: <-- [9:AT+FBO=0\r] > Apr 30 20:25:12.98: [ 1392]: --> [2:OK] > Apr 30 20:25:12.98: [ 1392]: <-- [10:AT+FCT=30\r] > Apr 30 20:25:13.12: [ 1392]: --> [2:OK] > Apr 30 20:25:13.12: [ 1392]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 20:25:13.26: [ 1392]: --> [2:OK] > Apr 30 20:25:13.26: [ 1392]: <-- [9:AT+FIE=0\r] > Apr 30 20:25:13.40: [ 1392]: --> [2:OK] > Apr 30 20:25:13.40: [ 1392]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 20:25:13.55: [ 1392]: --> [2:OK] > Apr 30 20:25:13.55: [ 1392]: <-- [5:ATM0\r] > Apr 30 20:25:13.69: [ 1392]: --> [2:OK] > Apr 30 20:25:13.69: [ 1392]: MODEM input buffering enabled > Apr 30 20:25:13.69: [ 1392]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 20:25:13.93: [ 1392]: --> [2:OK] > Apr 30 20:25:13.93: [ 1392]: <-- [9:AT+FLO=2\r] > Apr 30 20:25:14.17: [ 1392]: --> [2:OK] > Apr 30 20:25:14.17: [ 1392]: <-- [9:AT+FPP=0\r] > Apr 30 20:25:14.41: [ 1392]: --> [2:OK] > Apr 30 20:25:14.41: [ 1392]: <-- [9:AT+FBO=0\r] > Apr 30 20:25:14.65: [ 1392]: --> [2:OK] > Apr 30 20:25:14.65: [ 1392]: <-- [10:AT+FCT=30\r] > Apr 30 20:25:14.89: [ 1392]: --> [2:OK] > Apr 30 20:25:14.89: [ 1392]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 20:25:15.13: [ 1392]: --> [2:OK] > Apr 30 20:25:15.13: [ 1392]: <-- [9:AT+FIE=0\r] > Apr 30 20:25:15.37: [ 1392]: --> [2:OK] > Apr 30 20:25:15.37: [ 1392]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 20:25:15.62: [ 1392]: --> [2:OK] > Apr 30 20:25:15.62: [ 1392]: <-- [28:AT+FLI="HylaFax@silverwolf"\r] > Apr 30 20:25:15.87: [ 1392]: --> [2:OK] > Apr 30 20:25:15.87: [ 1392]: DIAL 02236604820 > Apr 30 20:25:15.87: [ 1392]: <-- [17:ATDT002236604820\r] > Apr 30 20:25:27.82: [ 1392]: --> [4:+FCO] > Apr 30 20:25:30.52: [ 1392]: --> [19:+FNF:y^V^� ^S^P^E^V^����^�^A] > Apr 30 20:25:30.52: [ 1392]: REMOTE NSF "y^V^� ^S^P^E^V^����^�^A" > Apr 30 20:25:30.52: [ 1392]: --> [27:+FCI:" +49 2236 604 820"] > Apr 30 20:25:30.52: [ 1392]: REMOTE CSI "+49 2236 604 820" > Apr 30 20:25:30.52: [ 1392]: --> [20:+FIS:1,5,0,2,1,0,0,4] > Apr 30 20:25:30.52: [ 1392]: --> [2:OK] > Apr 30 20:25:30.52: [ 1392]: REMOTE best rate 14400 bit/s > Apr 30 20:25:30.52: [ 1392]: REMOTE max page width 1728 pixels in 215 mm > Apr 30 20:25:30.52: [ 1392]: REMOTE max unlimited page length > Apr 30 20:25:30.52: [ 1392]: REMOTE best vres 7.7 line/mm > Apr 30 20:25:30.52: [ 1392]: REMOTE best format 2-D MR > Apr 30 20:25:30.52: [ 1392]: REMOTE best 20 ms, 10 ms/scanline > Apr 30 20:25:30.52: [ 1392]: USE 14400 bit/s > Apr 30 20:25:30.52: [ 1392]: USE 20 ms, 10 ms/scanline > Apr 30 20:25:30.52: [ 1392]: SEND file "docq/doc25.ps;00" > Apr 30 20:25:30.52: [ 1392]: USE page width 1728 pixels in 215 mm > Apr 30 20:25:30.52: [ 1392]: USE unlimited page length > Apr 30 20:25:30.52: [ 1392]: USE 3.85 line/mm > Apr 30 20:25:30.52: [ 1392]: USE 1-D MR > Apr 30 20:25:30.52: [ 1392]: <-- [23:AT+FIS=0,5,0,2,0,0,0,4\r] > Apr 30 20:25:30.77: [ 1392]: --> [2:OK] > Apr 30 20:25:30.77: [ 1392]: <-- [7:AT+FDT\r] > Apr 30 20:25:31.05: [ 1392]: --> [20:+FCS:0,5,0,2,0,0,0,4] > Apr 30 20:25:38.02: [ 1392]: --> [7:CONNECT] > Apr 30 20:25:38.02: [ 1392]: SEND begin page > Apr 30 20:25:57.96: [ 1392]: SENT 24433 bytes of data > D 1D RTC > Apr 30 20:25:57.96: [ 1392]: SEND end page > Apr 30 20:25:57.96: [ 1392]: SEND send MPS (more pages, same document) > Apr 30 20:26:14.11: [ 1392]: --> [5:ERROR] > Apr 30 20:26:14.11: [ 1392]: SEND recv RTN (retrain negative) > Apr 30 20:26:14.11: [ 1392]: <-- [7:AT+FDT\r] > Apr 30 20:26:14.24: [ 1392]: --> [2:OK] > Apr 30 20:29:14.24: [ 1392]: MODEM TIMEOUT: reading line from modem > Apr 30 20:29:14.24: [ 1392]: MODEM <Timeout> > Apr 30 20:29:14.24: [ 1392]: <-- [7:AT+FKS\r] > Apr 30 20:29:14.48: [ 1392]: --> [2:OK] > Apr 30 20:29:14.48: [ 1392]: <-- [5:ATH0\r] > Apr 30 20:29:14.72: [ 1392]: --> [2:OK] > Apr 30 20:29:14.72: [ 1392]: MODEM set DTR OFF > Apr 30 20:29:14.72: [ 1392]: SESSION END > > To: stefan.swoboda@i Date: 04/30/99 21:17 > Error: No response to MPS repeated 3 times > > ---- Transcript of session follows ---- > > Apr 30 21:17:11.24: [ 1921]: SESSION BEGIN 00000029 492236604820 > Apr 30 21:17:11.24: [ 1921]: SEND FAX: JOB 21 DEST 02236604820 COMMID > 00000029 > Apr 30 21:17:11.24: [ 1921]: MODEM set DTR OFF > Apr 30 21:17:11.24: [ 1921]: DELAY 2600 ms > Apr 30 21:17:13.84: [ 1921]: MODEM set DTR ON > Apr 30 21:17:13.84: [ 1921]: MODEM set baud rate: 19200 baud, input flow > RTS/CTS, output flow RTS/CTS > Apr 30 21:17:13.84: [ 1921]: MODEM flush i/o > Apr 30 21:17:13.84: [ 1921]: <-- [17:ATE0V1Q0X3S0=0H0\r] > Apr 30 21:17:13.99: [ 1921]: --> [2:OK] > Apr 30 21:17:13.99: [ 1921]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r] > Apr 30 21:17:14.14: [ 1921]: --> [2:OK] > Apr 30 21:17:14.14: [ 1921]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 21:17:14.28: [ 1921]: --> [2:OK] > Apr 30 21:17:14.28: [ 1921]: <-- [9:AT+FLO=2\r] > Apr 30 21:17:14.42: [ 1921]: --> [2:OK] > Apr 30 21:17:14.42: [ 1921]: <-- [9:AT+FPP=0\r] > Apr 30 21:17:14.56: [ 1921]: --> [2:OK] > Apr 30 21:17:14.56: [ 1921]: <-- [9:AT+FBO=0\r] > Apr 30 21:17:14.70: [ 1921]: --> [2:OK] > Apr 30 21:17:14.70: [ 1921]: <-- [10:AT+FCT=30\r] > Apr 30 21:17:14.84: [ 1921]: --> [2:OK] > Apr 30 21:17:14.84: [ 1921]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 21:17:14.98: [ 1921]: --> [2:OK] > Apr 30 21:17:14.98: [ 1921]: <-- [9:AT+FIE=0\r] > Apr 30 21:17:15.12: [ 1921]: --> [2:OK] > Apr 30 21:17:15.12: [ 1921]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 21:17:15.27: [ 1921]: --> [2:OK] > Apr 30 21:17:15.27: [ 1921]: <-- [5:ATM0\r] > Apr 30 21:17:15.41: [ 1921]: --> [2:OK] > Apr 30 21:17:15.41: [ 1921]: MODEM input buffering enabled > Apr 30 21:17:15.41: [ 1921]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 21:17:15.65: [ 1921]: --> [2:OK] > Apr 30 21:17:15.65: [ 1921]: <-- [9:AT+FLO=2\r] > Apr 30 21:17:15.89: [ 1921]: --> [2:OK] > Apr 30 21:17:15.89: [ 1921]: <-- [9:AT+FPP=0\r] > Apr 30 21:17:16.13: [ 1921]: --> [2:OK] > Apr 30 21:17:16.13: [ 1921]: <-- [9:AT+FBO=0\r] > Apr 30 21:17:16.37: [ 1921]: --> [2:OK] > Apr 30 21:17:16.37: [ 1921]: <-- [10:AT+FCT=30\r] > Apr 30 21:17:16.61: [ 1921]: --> [2:OK] > Apr 30 21:17:16.61: [ 1921]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 21:17:16.85: [ 1921]: --> [2:OK] > Apr 30 21:17:16.85: [ 1921]: <-- [9:AT+FIE=0\r] > Apr 30 21:17:17.09: [ 1921]: --> [2:OK] > Apr 30 21:17:17.09: [ 1921]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 21:17:17.34: [ 1921]: --> [2:OK] > Apr 30 21:17:17.34: [ 1921]: <-- [28:AT+FLI="HylaFax@silverwolf"\r] > Apr 30 21:17:17.59: [ 1921]: --> [2:OK] > Apr 30 21:17:17.59: [ 1921]: DIAL 02236604820 > Apr 30 21:17:17.59: [ 1921]: <-- [17:ATDT002236604820\r] > Apr 30 21:17:29.59: [ 1921]: --> [4:+FCO] > Apr 30 21:17:32.28: [ 1921]: --> [19:+FNF:y^V^� ^S^P^E^V^����^�^A] > Apr 30 21:17:32.28: [ 1921]: REMOTE NSF "y^V^� ^S^P^E^V^����^�^A" > Apr 30 21:17:32.28: [ 1921]: --> [27:+FCI:" +49 2236 604 820"] > Apr 30 21:17:32.28: [ 1921]: REMOTE CSI "+49 2236 604 820" > Apr 30 21:17:32.28: [ 1921]: --> [20:+FIS:1,5,0,2,1,0,0,4] > Apr 30 21:17:32.28: [ 1921]: --> [2:OK] > Apr 30 21:17:32.28: [ 1921]: REMOTE best rate 14400 bit/s > Apr 30 21:17:32.28: [ 1921]: REMOTE max page width 1728 pixels in 215 mm > Apr 30 21:17:32.28: [ 1921]: REMOTE max unlimited page length > Apr 30 21:17:32.28: [ 1921]: REMOTE best vres 7.7 line/mm > Apr 30 21:17:32.28: [ 1921]: REMOTE best format 2-D MR > Apr 30 21:17:32.28: [ 1921]: REMOTE best 20 ms, 10 ms/scanline > Apr 30 21:17:32.28: [ 1921]: USE 14400 bit/s > Apr 30 21:17:32.28: [ 1921]: USE 20 ms, 10 ms/scanline > Apr 30 21:17:32.28: [ 1921]: SEND file "docq/doc37.ps;00" > Apr 30 21:17:32.28: [ 1921]: USE page width 1728 pixels in 215 mm > Apr 30 21:17:32.28: [ 1921]: USE unlimited page length > Apr 30 21:17:32.28: [ 1921]: USE 3.85 line/mm > Apr 30 21:17:32.28: [ 1921]: USE 1-D MR > Apr 30 21:17:32.28: [ 1921]: <-- [23:AT+FIS=0,5,0,2,0,0,0,4\r] > Apr 30 21:17:32.53: [ 1921]: --> [2:OK] > Apr 30 21:17:32.53: [ 1921]: <-- [7:AT+FDT\r] > Apr 30 21:17:32.81: [ 1921]: --> [20:+FCS:0,5,0,2,0,0,0,4] > Apr 30 21:17:39.78: [ 1921]: --> [7:CONNECT] > Apr 30 21:17:39.78: [ 1921]: SEND begin page > Apr 30 21:17:59.72: [ 1921]: SENT 24431 bytes of data > D RTC > Apr 30 21:17:59.72: [ 1921]: SEND end page > Apr 30 21:17:59.72: [ 1921]: SEND send MPS (more pages, same document) > Apr 30 21:18:21.10: [ 1921]: --> [7:+FHS:52] > Apr 30 21:18:21.10: [ 1921]: REMOTE HANGUP: No response to MPS repeated 3 > times (code 52) > Apr 30 21:18:21.10: [ 1921]: <-- [5:ATH0\r] > Apr 30 21:18:21.22: [ 1921]: --> [2:OK] > Apr 30 21:18:21.22: [ 1921]: MODEM set DTR OFF > Apr 30 21:18:21.22: [ 1921]: SESSION END > > To: stefan.swoboda@i Date: 04/30/99 21:22 > Error: No response to MPS repeated 3 times > > ---- Transcript of session follows ---- > > Apr 30 21:22:08.97: [ 2007]: SESSION BEGIN 00000031 49211452776 > Apr 30 21:22:08.98: [ 2007]: SEND FAX: JOB 23 DEST 452776 COMMID 00000031 > Apr 30 21:22:08.98: [ 2007]: MODEM set DTR OFF > Apr 30 21:22:08.98: [ 2007]: DELAY 2600 ms > Apr 30 21:22:11.58: [ 2007]: MODEM set DTR ON > Apr 30 21:22:11.58: [ 2007]: MODEM set baud rate: 19200 baud, input flow > RTS/CTS, output flow RTS/CTS > Apr 30 21:22:11.58: [ 2007]: MODEM flush i/o > Apr 30 21:22:11.58: [ 2007]: <-- [17:ATE0V1Q0X3S0=0H0\r] > Apr 30 21:22:11.73: [ 2007]: --> [2:OK] > Apr 30 21:22:11.73: [ 2007]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r] > Apr 30 21:22:11.88: [ 2007]: --> [2:OK] > Apr 30 21:22:11.88: [ 2007]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 21:22:12.02: [ 2007]: --> [2:OK] > Apr 30 21:22:12.02: [ 2007]: <-- [9:AT+FLO=2\r] > Apr 30 21:22:12.16: [ 2007]: --> [2:OK] > Apr 30 21:22:12.16: [ 2007]: <-- [9:AT+FPP=0\r] > Apr 30 21:22:12.30: [ 2007]: --> [2:OK] > Apr 30 21:22:12.30: [ 2007]: <-- [9:AT+FBO=0\r] > Apr 30 21:22:12.44: [ 2007]: --> [2:OK] > Apr 30 21:22:12.44: [ 2007]: <-- [10:AT+FCT=30\r] > Apr 30 21:22:12.58: [ 2007]: --> [2:OK] > Apr 30 21:22:12.58: [ 2007]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 21:22:12.72: [ 2007]: --> [2:OK] > Apr 30 21:22:12.72: [ 2007]: <-- [9:AT+FIE=0\r] > Apr 30 21:22:12.86: [ 2007]: --> [2:OK] > Apr 30 21:22:12.86: [ 2007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 21:22:13.01: [ 2007]: --> [2:OK] > Apr 30 21:22:13.01: [ 2007]: <-- [5:ATM0\r] > Apr 30 21:22:13.15: [ 2007]: --> [2:OK] > Apr 30 21:22:13.15: [ 2007]: MODEM input buffering enabled > Apr 30 21:22:13.15: [ 2007]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 21:22:13.39: [ 2007]: --> [2:OK] > Apr 30 21:22:13.39: [ 2007]: <-- [9:AT+FLO=2\r] > Apr 30 21:22:13.63: [ 2007]: --> [2:OK] > Apr 30 21:22:13.63: [ 2007]: <-- [9:AT+FPP=0\r] > Apr 30 21:22:13.87: [ 2007]: --> [2:OK] > Apr 30 21:22:13.87: [ 2007]: <-- [9:AT+FBO=0\r] > Apr 30 21:22:14.11: [ 2007]: --> [2:OK] > Apr 30 21:22:14.11: [ 2007]: <-- [10:AT+FCT=30\r] > Apr 30 21:22:14.35: [ 2007]: --> [2:OK] > Apr 30 21:22:14.35: [ 2007]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 21:22:14.59: [ 2007]: --> [2:OK] > Apr 30 21:22:14.59: [ 2007]: <-- [9:AT+FIE=0\r] > Apr 30 21:22:14.83: [ 2007]: --> [2:OK] > Apr 30 21:22:14.83: [ 2007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 21:22:15.08: [ 2007]: --> [2:OK] > Apr 30 21:22:15.08: [ 2007]: <-- [28:AT+FLI="HylaFax@silverwolf"\r] > Apr 30 21:22:15.33: [ 2007]: --> [2:OK] > Apr 30 21:22:15.33: [ 2007]: DIAL 452776 > Apr 30 21:22:15.33: [ 2007]: <-- [12:ATDT0452776\r] > Apr 30 21:22:27.68: [ 2007]: --> [4:+FCO] > Apr 30 21:22:30.65: [ 2007]: --> [24:+FNF: > ^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P] > Apr 30 21:22:30.65: [ 2007]: REMOTE NSF " > ^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P" > Apr 30 21:22:30.65: [ 2007]: --> [27:+FCI:" +49 211 452776"] > Apr 30 21:22:30.65: [ 2007]: REMOTE CSI "+49 211 452776" > Apr 30 21:22:30.65: [ 2007]: --> [20:+FIS:1,3,0,2,0,0,0,4] > Apr 30 21:22:30.65: [ 2007]: --> [2:OK] > Apr 30 21:22:30.65: [ 2007]: REMOTE best rate 9600 bit/s > Apr 30 21:22:30.65: [ 2007]: REMOTE max page width 1728 pixels in 215 mm > Apr 30 21:22:30.65: [ 2007]: REMOTE max unlimited page length > Apr 30 21:22:30.65: [ 2007]: REMOTE best vres 7.7 line/mm > Apr 30 21:22:30.65: [ 2007]: REMOTE best format 1-D MR > Apr 30 21:22:30.65: [ 2007]: REMOTE best 20 ms, 10 ms/scanline > Apr 30 21:22:30.65: [ 2007]: USE 9600 bit/s > Apr 30 21:22:30.65: [ 2007]: USE 20 ms, 10 ms/scanline > Apr 30 21:22:30.65: [ 2007]: SEND file "docq/doc41.ps;00" > Apr 30 21:22:30.65: [ 2007]: USE page width 1728 pixels in 215 mm > Apr 30 21:22:30.65: [ 2007]: USE unlimited page length > Apr 30 21:22:30.65: [ 2007]: USE 3.85 line/mm > Apr 30 21:22:30.65: [ 2007]: USE 1-D MR > Apr 30 21:22:30.65: [ 2007]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r] > Apr 30 21:22:30.90: [ 2007]: --> [2:OK] > Apr 30 21:22:30.90: [ 2007]: <-- [7:AT+FDT\r] > Apr 30 21:22:31.18: [ 2007]: --> [20:+FCS:0,3,0,2,0,0,0,4] > Apr 30 21:22:37.07: [ 2007]: --> [7:CONNECT] > Apr 30 21:22:37.07: [ 2007]: SEND begin page > Apr 30 21:23:01.19: [ 2007]: SENT 24432 bytes of data > Apr 30 21:23:01.19: [ 2007]: SEND 1D RTC > 30 21:23:01.19: [ 2007]: SEND end page > Apr 30 21:23:01.19: [ 2007]: SEND send MPS (more pages, same document) > Apr 30 21:23:23.42: [ 2007]: --> [7:+FHS:52] > Apr 30 21:23:23.42: [ 2007]: REMOTE HANGUP: No response to MPS repeated 3 > times (code 52) > Apr 30 21:23:23.42: [ 2007]: <-- [5:ATH0\r] > Apr 30 21:23:23.55: [ 2007]: --> [2:OK] > Apr 30 21:23:23.55: [ 2007]: MODEM set DTR OFF > Apr 30 21:23:23.55: [ 2007]: SESSION END > > To: stefan.swoboda@i Date: 04/30/99 23:05 > Error: No response to MPS repeated 3 times > > ---- Transcript of session follows ---- > > Apr 30 23:05:07.99: [ 2269]: SESSION BEGIN 00000033 49211452776 > Apr 30 23:05:08.00: [ 2269]: SEND FAX: JOB 24 DEST 452776 COMMID 00000033 > Apr 30 23:05:08.00: [ 2269]: MODEM set DTR OFF > Apr 30 23:05:08.00: [ 2269]: DELAY 2600 ms > Apr 30 23:05:10.60: [ 2269]: MODEM set DTR ON > Apr 30 23:05:10.60: [ 2269]: MODEM set baud rate: 19200 baud, input flow > RTS/CTS, output flow RTS/CTS > Apr 30 23:05:10.60: [ 2269]: MODEM flush i/o > Apr 30 23:05:10.60: [ 2269]: <-- [17:ATE0V1Q0X3S0=0H0\r] > Apr 30 23:05:10.75: [ 2269]: --> [2:OK] > Apr 30 23:05:10.75: [ 2269]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r] > Apr 30 23:05:10.90: [ 2269]: --> [2:OK] > Apr 30 23:05:10.90: [ 2269]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 23:05:11.04: [ 2269]: --> [2:OK] > Apr 30 23:05:11.04: [ 2269]: <-- [9:AT+FLO=2\r] > Apr 30 23:05:11.18: [ 2269]: --> [2:OK] > Apr 30 23:05:11.18: [ 2269]: <-- [9:AT+FPP=0\r] > Apr 30 23:05:11.32: [ 2269]: --> [2:OK] > Apr 30 23:05:11.32: [ 2269]: <-- [9:AT+FBO=0\r] > Apr 30 23:05:11.46: [ 2269]: --> [2:OK] > Apr 30 23:05:11.46: [ 2269]: <-- [10:AT+FCT=30\r] > Apr 30 23:05:11.60: [ 2269]: --> [2:OK] > Apr 30 23:05:11.60: [ 2269]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 23:05:11.74: [ 2269]: --> [2:OK] > Apr 30 23:05:11.74: [ 2269]: <-- [9:AT+FIE=0\r] > Apr 30 23:05:11.88: [ 2269]: --> [2:OK] > Apr 30 23:05:11.88: [ 2269]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 23:05:12.03: [ 2269]: --> [2:OK] > Apr 30 23:05:12.03: [ 2269]: <-- [5:ATM0\r] > Apr 30 23:05:12.17: [ 2269]: --> [2:OK] > Apr 30 23:05:12.17: [ 2269]: MODEM input buffering enabled > Apr 30 23:05:12.17: [ 2269]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 23:05:12.41: [ 2269]: --> [2:OK] > Apr 30 23:05:12.41: [ 2269]: <-- [9:AT+FLO=2\r] > Apr 30 23:05:12.65: [ 2269]: --> [2:OK] > Apr 30 23:05:12.65: [ 2269]: <-- [9:AT+FPP=0\r] > Apr 30 23:05:12.89: [ 2269]: --> [2:OK] > Apr 30 23:05:12.89: [ 2269]: <-- [9:AT+FBO=0\r] > Apr 30 23:05:13.13: [ 2269]: --> [2:OK] > Apr 30 23:05:13.13: [ 2269]: <-- [10:AT+FCT=30\r] > Apr 30 23:05:13.37: [ 2269]: --> [2:OK] > Apr 30 23:05:13.37: [ 2269]: <-- [15:AT+FNR=1,1,1,1\r] > Apr 30 23:05:13.61: [ 2269]: --> [2:OK] > Apr 30 23:05:13.61: [ 2269]: <-- [9:AT+FIE=0\r] > Apr 30 23:05:13.85: [ 2269]: --> [2:OK] > Apr 30 23:05:13.85: [ 2269]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 23:05:14.10: [ 2269]: --> [2:OK] > Apr 30 23:05:14.10: [ 2269]: <-- [28:AT+FLI="HylaFax@silverwolf"\r] > Apr 30 23:05:14.35: [ 2269]: --> [2:OK] > Apr 30 23:05:14.35: [ 2269]: DIAL 452776 > Apr 30 23:05:14.35: [ 2269]: <-- [12:ATDT0452776\r] > Apr 30 23:05:26.67: [ 2269]: --> [4:+FCO] > Apr 30 23:05:29.63: [ 2269]: --> [24:+FNF: > ^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P] > Apr 30 23:05:29.63: [ 2269]: REMOTE NSF " > ^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P" > Apr 30 23:05:29.63: [ 2269]: --> [27:+FCI:" +49 211 452776"] > Apr 30 23:05:29.63: [ 2269]: REMOTE CSI "+49 211 452776" > Apr 30 23:05:29.63: [ 2269]: --> [20:+FIS:1,3,0,2,0,0,0,4] > Apr 30 23:05:29.63: [ 2269]: --> [2:OK] > Apr 30 23:05:29.63: [ 2269]: REMOTE best rate 9600 bit/s > Apr 30 23:05:29.63: [ 2269]: REMOTE max page width 1728 pixels in 215 mm > Apr 30 23:05:29.63: [ 2269]: REMOTE max unlimited page length > Apr 30 23:05:29.63: [ 2269]: REMOTE best vres 7.7 line/mm > Apr 30 23:05:29.63: [ 2269]: REMOTE best format 1-D MR > Apr 30 23:05:29.63: [ 2269]: REMOTE best 20 ms, 10 ms/scanline > Apr 30 23:05:29.63: [ 2269]: USE 9600 bit/s > Apr 30 23:05:29.63: [ 2269]: USE 20 ms, 10 ms/scanline > Apr 30 23:05:29.63: [ 2269]: SEND file "docq/doc43.ps;00" > Apr 30 23:05:29.63: [ 2269]: USE page width 1728 pixels in 215 mm > Apr 30 23:05:29.63: [ 2269]: USE unlimited page length > Apr 30 23:05:29.63: [ 2269]: USE 3.85 line/mm > Apr 30 23:05:29.63: [ 2269]: USE 1-D MR > Apr 30 23:05:29.63: [ 2269]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r] > Apr 30 23:05:29.88: [ 2269]: --> [2:OK] > Apr 30 23:05:29.88: [ 2269]: <-- [7:AT+FDT\r] > Apr 30 23:05:30.16: [ 2269]: --> [20:+FCS:0,3,0,2,0,0,0,4] > Apr 30 23:05:35.73: [ 2269]: --> [20:+FCS:0,2,0,2,0,0,0,4] > Apr 30 23:05:41.64: [ 2269]: --> [7:CONNECT] > Apr 30 23:05:41.64: [ 2269]: SEND begin page > bytes of data > Apr 30 23:06:10.15: [ 2269]: SEND 1D RTC > Apr 30 23:06:10.15: [ 2269]: SEND end page > Apr 30 23:06:10.15: [ 2269]: SEND send MPS (more pages, same document) > Apr 30 23:06:33.43: [ 2269]: --> [7:+FHS:52] > Apr 30 23:06:33.43: [ 2269]: REMOTE HANGUP: No response to MPS repeated 3 > times (code 52) > Apr 30 23:06:33.43: [ 2269]: <-- [5:ATH0\r] > Apr 30 23:06:33.55: [ 2269]: --> [2:OK] > Apr 30 23:06:33.55: [ 2269]: MODEM set DTR OFF > Apr 30 23:06:33.55: [ 2269]: SESSION END > > To: stefan.swoboda@i Date: 04/30/99 23:14 > Error: No response to MPS repeated 3 times > > ---- Transcript of session follows ---- > > Apr 30 23:14:03.58: [ 2629]: SESSION BEGIN 00000034 49211452776 > Apr 30 23:14:03.58: [ 2629]: SEND FAX: JOB 25 DEST 452776 COMMID 00000034 > Apr 30 23:14:03.58: [ 2629]: MODEM set DTR OFF > Apr 30 23:14:03.58: [ 2629]: DELAY 2600 ms > Apr 30 23:14:06.18: [ 2629]: MODEM set DTR ON > Apr 30 23:14:06.18: [ 2629]: MODEM set baud rate: 19200 baud, input flow > RTS/CTS, output flow RTS/CTS > Apr 30 23:14:06.18: [ 2629]: MODEM flush i/o > Apr 30 23:14:06.18: [ 2629]: <-- [17:ATE0V1Q0X3S0=0H0\r] > Apr 30 23:14:06.33: [ 2629]: --> [2:OK] > Apr 30 23:14:06.33: [ 2629]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r] > Apr 30 23:14:06.48: [ 2629]: --> [2:OK] > Apr 30 23:14:06.48: [ 2629]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 23:14:06.62: [ 2629]: --> [2:OK] > Apr 30 23:14:06.62: [ 2629]: <-- [9:AT+FLO=2\r] > Apr 30 23:14:06.76: [ 2629]: --> [2:OK] > Apr 30 23:14:06.76: [ 2629]: <-- [9:AT+FPP=0\r] > Apr 30 23:14:06.90: [ 2629]: --> [2:OK] > Apr 30 23:14:06.90: [ 2629]: <-- [9:AT+FBO=0\r] > Apr 30 23:14:07.04: [ 2629]: --> [2:OK] > Apr 30 23:14:07.04: [ 2629]: <-- [10:AT+FCT=30\r] > Apr 30 23:14:07.18: [ 2629]: --> [2:OK] > Apr 30 23:14:07.18: [ 2629]: <-- [15:AT+FNR=1,1,1,0\r] > Apr 30 23:14:07.32: [ 2629]: --> [2:OK] > Apr 30 23:14:07.32: [ 2629]: <-- [9:AT+FIE=0\r] > Apr 30 23:14:07.46: [ 2629]: --> [2:OK] > Apr 30 23:14:07.46: [ 2629]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 23:14:07.61: [ 2629]: --> [2:OK] > Apr 30 23:14:07.61: [ 2629]: <-- [5:ATM0\r] > Apr 30 23:14:07.75: [ 2629]: --> [2:OK] > Apr 30 23:14:07.75: [ 2629]: MODEM input buffering enabled > Apr 30 23:14:07.75: [ 2629]: <-- [14:AT+FCLASS=2.0\r] > Apr 30 23:14:07.99: [ 2629]: --> [2:OK] > Apr 30 23:14:07.99: [ 2629]: <-- [9:AT+FLO=2\r] > Apr 30 23:14:08.23: [ 2629]: --> [2:OK] > Apr 30 23:14:08.23: [ 2629]: <-- [9:AT+FPP=0\r] > Apr 30 23:14:08.47: [ 2629]: --> [2:OK] > Apr 30 23:14:08.47: [ 2629]: <-- [9:AT+FBO=0\r] > Apr 30 23:14:08.71: [ 2629]: --> [2:OK] > Apr 30 23:14:08.71: [ 2629]: <-- [10:AT+FCT=30\r] > Apr 30 23:14:08.95: [ 2629]: --> [2:OK] > Apr 30 23:14:08.95: [ 2629]: <-- [15:AT+FNR=1,1,1,0\r] > Apr 30 23:14:09.19: [ 2629]: --> [2:OK] > Apr 30 23:14:09.19: [ 2629]: <-- [9:AT+FIE=0\r] > Apr 30 23:14:09.43: [ 2629]: --> [2:OK] > Apr 30 23:14:09.43: [ 2629]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] > Apr 30 23:14:09.68: [ 2629]: --> [2:OK] > Apr 30 23:14:09.68: [ 2629]: <-- [28:AT+FLI="HylaFax@silverwolf"\r] > Apr 30 23:14:09.93: [ 2629]: --> [2:OK] > Apr 30 23:14:09.93: [ 2629]: DIAL 452776 > Apr 30 23:14:09.93: [ 2629]: <-- [12:ATDT0452776\r] > Apr 30 23:14:22.30: [ 2629]: --> [4:+FCO] > Apr 30 23:14:25.25: [ 2629]: --> [27:+FCI:" +49 211 452776"] > Apr 30 23:14:25.25: [ 2629]: REMOTE CSI "+49 211 452776" > Apr 30 23:14:25.25: [ 2629]: --> [20:+FIS:1,3,0,2,0,0,0,4] > Apr 30 23:14:25.25: [ 2629]: --> [2:OK] > Apr 30 23:14:25.25: [ 2629]: REMOTE best rate 9600 bit/s > Apr 30 23:14:25.25: [ 2629]: REMOTE max page width 1728 pixels in 215 mm > Apr 30 23:14:25.25: [ 2629]: REMOTE max unlimited page length > Apr 30 23:14:25.25: [ 2629]: REMOTE best vres 7.7 line/mm > Apr 30 23:14:25.25: [ 2629]: REMOTE best format 1-D MR > Apr 30 23:14:25.25: [ 2629]: REMOTE best 20 ms, 10 ms/scanline > Apr 30 23:14:25.25: [ 2629]: USE 9600 bit/s > Apr 30 23:14:25.25: [ 2629]: USE 20 ms, 10 ms/scanline > Apr 30 23:14:25.25: [ 2629]: SEND file "docq/doc45.ps;00" > Apr 30 23:14:25.25: [ 2629]: USE page width 1728 pixels in 215 mm > Apr 30 23:14:25.25: [ 2629]: USE unlimited page length > Apr 30 23:14:25.25: [ 2629]: USE 3.85 line/mm > Apr 30 23:14:25.25: [ 2629]: USE 1-D MR > Apr 30 23:14:25.25: [ 2629]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r] > Apr 30 23:14:25.50: [ 2629]: --> [2:OK] > Apr 30 23:14:25.50: [ 2629]: <-- [7:AT+FDT\r] > Apr 30 23:14:25.78: [ 2629]: --> [20:+FCS:0,3,0,2,0,0,0,4] > Apr 30 23:14:31.69: [ 2629]: --> [7:CONNECT] > Apr 30 23:14:31.69: [ 2629]: SEND begin page > Apr 30 23:14:55.81: [ 2629]: SENT 24438 bytes of data > Apr 30 23:14:55.81: [ 2629]: SEND 1D RTC > Apr 30 23:14:55.81: [ 2629]: SEND end page > Apr 30 23:14:55.81: [ 2629]: SEND send MPS (more pages, same document) > .05: [ 2629]: --> [7:+FHS:52] > Apr 30 23:15:18.05: [ 2629]: REMOTE HANGUP: No response to MPS repeated 3 > times (code 52) > Apr 30 23:15:18.05: [ 2629]: <-- [5:ATH0\r] > Apr 30 23:15:18.18: [ 2629]: --> [2:OK] > Apr 30 23:15:18.18: [ 2629]: MODEM set DTR OFF > Apr 30 23:15:18.18: [ 2629]: SESSION END > > Nothing to purge in info directory. > > Truncate merged session logs older than 30 days: > > Nothing to purge in receive queue. > > Nothing to purge in the tmp directory. > > Destinations being rejected (added since 04/29/99 23:25): > > Regards, > Stefan Swoboda > System Engineer > sswoboda@ford.com > Ford Motor Company > Tel.: +49 221 9034806 > International Local Design & Implementation > Fax: +49 221 9033017 > > > -----Original Message----- > > From: Philip Rhoades [SMTP:philr@mail.austasia.net] > > Sent: 09 May 1999 03:26 > > To: flexfax@sgi.com > > Subject: flexfax: Is there a solution to the "No response to MPS or > > EOP" problem? > > > > Hi all, > > > > I have looked at the archives but I can't find a solution to the problem I > > get sending to some fax machines ie: > > > > "Your facsimile job to 08-8232-2924 failed because: > > No response to MPS or EOP repeated 3 tries; Giving up after 3 attempts > > to send same page" > > > > I have tried a 3Com US Robotics 56K Voice Faxmodem and a Netcomm 56K > > Roadster with the same result. > > > > I seem to be getting this result about 25% of the time from various fax > > machines - some are new, some older. > > > > I will have to go back to paper faxing (which drives me crazy!) if I can't > > rely on a computer method. > > > > Thanks, > > > > Phil. > > > > Philip Rhoades > > > > Pricom Pty Limited (ACN 003 252 275) > > GPO Box 3411 > > Sydney NSW 2001 > > Australia > > Mobile: +61:0411-185-652 > > Fax: +61:2:9959-4909 > > E-mail: philr@mail.austasia.net > > > >
- Follow-Ups:
- Re: Is there a solution to the "No response to MPS or EOP"
- From: David Woolley <david@djwhome.demon.co.uk>
- Re: Is there a solution to the "No response to MPS or EOP"
- Prev by Date: DTMF routing using Hylafax.
- Next by Date: problem building libtiff DSO on AIX
- Prev by thread: RE: Is there a solution to the "No response to MPS or EOP" problem?
- Next by thread: Re: Is there a solution to the "No response to MPS or EOP"
- Index(es):
Project hosted by iFAX Solutions