Re: flexfax: hylafax and USR courrier ISDN

[hugues@expert-telecom.com]

I 'think we have solve the pb

this is our new config.cua0

CountryCode:            33
AreaCode:               04
FAXNumber:              
InternationalPrefix:    00
DialStringRules:        "etc/dialrules"
ServerTracing:          0x201
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      10
SpeakerVolume:          off
GettyArgs:              "-x 9 %l F%s"
LocalIdentifier:        ""
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           25
#
# Mise en place des delai d'attente
JobReqBusy:             180             # internvalle d'attente entre 2 busy en sec
JobNoAnswer:            180             # intervalle d'attente entre 2 no answer
JobNoCarrier:           180             # intervalle                    no carrier
JobReqOther:            180             # intervalle de temps entre 2 erreurs autres
MaxDials:               7               # nombre max de sonnerie
MaxTries:               3               # nombre d'essai
NoCarrierRetrys:        1               # pas de re-essai en cas de no carrier
PercentGoodLines:       50              # page ok a 50%
MaxConsecutiveBadLines: 100             # 100 lignes mauvaises sur 1781 est OK
Use2D:                  yes             # possibilit� d'utiliser 2D encodage + rapide!!
PageChop:               all             # possibilit� de remplacer les blanc/ vide + rapide!!
PageChopThreshold:      2               # distance min (inch) pour choper !!
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              19200           # DCE-DTE communication rate
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
ModemResultCodesCmd:    ATQ0X4          # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#


CountryCode:            33
AreaCode:               04
FAXNumber:              FAXEXPERT
InternationalPrefix:    00
DialStringRules:        "etc/dialrules"
ServerTracing:          0x201
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      10
SpeakerVolume:          off
GettyArgs:              "-x 9 %l F%s"
LocalIdentifier:        "http://www.FaxExpert.com"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           25
#
# Mise en place des delai d'attente
JobReqBusy:             180             # internvalle d'attente entre 2 busy en sec
JobNoAnswer:            180             # intervalle d'attente entre 2 no answer
JobNoCarrier:           180             # intervalle                    no carrier
JobReqOther:            180             # intervalle de temps entre 2 erreurs autres
MaxDials:               7               # nombre max de sonnerie
MaxTries:               3               # nombre d'essai
NoCarrierRetrys:        1               # pas de re-essai en cas de no carrier
PercentGoodLines:       50              # page ok a 50%
MaxConsecutiveBadLines: 100             # 100 lignes mauvaises sur 1781 est OK
Use2D:                  yes             # possibilit� d'utiliser 2D encodage + rapide!!
PageChop:               all             # possibilit� de remplacer les blanc/ vide + rapide!!
PageChopThreshold:      2               # distance min (inch) pour choper !!
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              19200           # DCE-DTE communication rate
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
ModemResultCodesCmd:    ATQ0X4          # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
> From:          David Woolley <david@djwhome.demon.co.uk>
> Subject:       Re: flexfax: hylafax and USR courrier ISDN
> To:            hugues@expert-telecom.com
> Date:          Thu, 4 Mar 1999 08:25:09 +0000 (GMT)
> Cc:            flexfax@sgi.com
> Reply-to:      flexfax@sgi.com

> > 
> > if you have other idea ?
> 
> You still need to provide session logs.
> 
Salutations
L'�quipe de FaxExpert

***********************************************
Welcome on FaxExpert's World

http://www.faxexpert.com

EuroStrateges FaxExpert
8 Chemin du Jubin
69570 DARDILLY - FRANCE
Tel : (33) (0)4 72 521 440
fax : (33) (0)4 72 521 445
question@faxexpert.com
*********************************************