Re: flexfax: Need to know what this error means

[Jonathan Terry <jterry@iquest.net>]

I was only sending a single page, but I will try sending 2 or 3 and see what
happens.
My modem is a USR Sportster 33.6.  It is detected by Hylafax as a Class 2.0
modem.  I am connecting to an HP Office Jet 300 that our company receives most
of our faxes on.  I believe the phone line I am using is good becuase I use it
for other purposes as well and I don't have any troubles.  At least not yet. :)
Other faxes always come in ok.  My version of hylafax is hylafax-4.0pl2-3rh5 for
RedHat Linux 5.1.  I had used another RPM of it that didn't work at all so I
removed it and tried this one and it appears to work much better.  What is DCN
by the way?

Here is the trace I have:

Oct 16 16:47:47.89: [  499]: SESSION BEGIN 00000007 131795765044
Oct 16 16:47:47.90: [  499]: SEND FAX: JOB 5 DEST 95765044 COMMID 00000007
Oct 16 16:47:47.90: [  499]: DELAY 2600 ms
Oct 16 16:47:50.51: [  499]: <-- [15:ATE0V1Q0S0=0H0\r]
Oct 16 16:47:50.66: [  499]: --> [2:OK]
Oct 16 16:47:50.66: [  499]: <-- [12:ATS8=2S7=60\r]
Oct 16 16:47:50.80: [  499]: --> [2:OK]
Oct 16 16:47:50.80: [  499]: <-- [14:AT+FCLASS=2.0\r]
Oct 16 16:47:50.95: [  499]: --> [2:OK]
Oct 16 16:47:50.95: [  499]: <-- [9:AT+FLO=2\r]
Oct 16 16:47:51.09: [  499]: --> [2:OK]
Oct 16 16:47:51.09: [  499]: <-- [9:AT+FPP=0\r]
Oct 16 16:47:51.23: [  499]: --> [2:OK]
Oct 16 16:47:51.23: [  499]: <-- [9:AT+FBO=0\r]
Oct 16 16:47:51.37: [  499]: --> [2:OK]
Oct 16 16:47:51.37: [  499]: <-- [10:AT+FCT=30\r]
Oct 16 16:47:51.51: [  499]: --> [2:OK]
Oct 16 16:47:51.51: [  499]: <-- [15:AT+FNR=1,1,1,1\r]
Oct 16 16:47:51.66: [  499]: --> [2:OK]
Oct 16 16:47:51.66: [  499]: <-- [9:AT+FIE=0\r]
Oct 16 16:47:51.80: [  499]: --> [2:OK]
Oct 16 16:47:51.80: [  499]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 16 16:47:51.95: [  499]: --> [2:OK]
Oct 16 16:47:51.95: [  499]: <-- [7:ATL0M1\r]
Oct 16 16:47:52.09: [  499]: --> [2:OK]
Oct 16 16:47:52.09: [  499]: <-- [14:AT+FCLASS=2.0\r]
Oct 16 16:47:52.34: [  499]: --> [2:OK]
Oct 16 16:47:52.34: [  499]: <-- [9:AT+FLO=2\r]
Oct 16 16:47:52.58: [  499]: --> [2:OK]
Oct 16 16:47:52.58: [  499]: <-- [9:AT+FPP=0\r]
Oct 16 16:47:52.82: [  499]: --> [2:OK]
Oct 16 16:47:52.82: [  499]: <-- [9:AT+FBO=0\r]
Oct 16 16:47:53.06: [  499]: --> [2:OK]
Oct 16 16:47:53.06: [  499]: <-- [10:AT+FCT=30\r]
Oct 16 16:47:53.30: [  499]: --> [2:OK]
Oct 16 16:47:53.30: [  499]: <-- [15:AT+FNR=1,1,1,1\r]
Oct 16 16:47:53.55: [  499]: --> [2:OK]
Oct 16 16:47:53.55: [  499]: <-- [9:AT+FIE=0\r]
Oct 16 16:47:53.79: [  499]: --> [2:OK]
Oct 16 16:47:53.79: [  499]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 16 16:47:54.04: [  499]: --> [2:OK]
Oct 16 16:47:54.04: [  499]: <-- [22:AT+FLI="NothingSetup"\r]
Oct 16 16:47:54.29: [  499]: --> [2:OK]
Oct 16 16:47:54.30: [  499]: DIAL 95765044
Oct 16 16:47:54.31: [  499]: <-- [13:ATDT95765044\r]
Oct 16 16:48:05.46: [  499]: --> [4:+FCO]
Oct 16 16:48:08.08: [  499]: --> [12:+FNF:�6@��
�]
Oct 16 16:48:08.08: [  499]: REMOTE NSF "�6@��
�"
Oct 16 16:48:08.08: [  499]: --> [27:+FCI:"        317 576 5044"]
Oct 16 16:48:08.08: [  499]: REMOTE CSI "317 576 5044"
Oct 16 16:48:08.08: [  499]: --> [20:+FIS:1,3,0,2,1,0,0,4]
Oct 16 16:48:08.08: [  499]: --> [2:OK]
Oct 16 16:48:08.08: [  499]: REMOTE best rate 9600 bit/s
Oct 16 16:48:08.09: [  499]: REMOTE max page width 1728 pixels in 215 mm
Oct 16 16:48:08.09: [  499]: REMOTE max unlimited page length 
Oct 16 16:48:08.09: [  499]: REMOTE best vres 7.7 line/mm
Oct 16 16:48:08.09: [  499]: REMOTE best format 2-D MR
Oct 16 16:48:08.09: [  499]: REMOTE best 20 ms, 10 ms/scanline
Oct 16 16:48:08.09: [  499]: USE 9600 bit/s
Oct 16 16:48:08.09: [  499]: USE 20 ms, 10 ms/scanline
Oct 16 16:48:08.09: [  499]: SEND file "docq/doc5.ps;00"
Oct 16 16:48:08.10: [  499]: USE page width 1728 pixels in 215 mm
Oct 16 16:48:08.10: [  499]: USE unlimited page length 
Oct 16 16:48:08.10: [  499]: USE 3.85 line/mm
Oct 16 16:48:08.10: [  499]: USE 1-D MR
Oct 16 16:48:08.11: [  499]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Oct 16 16:48:08.36: [  499]: --> [2:OK]
Oct 16 16:48:08.36: [  499]: <-- [7:AT+FDT\r]
Oct 16 16:48:08.64: [  499]: --> [20:+FCS:0,3,0,2,0,0,0,4]
Oct 16 16:48:14.35: [  499]: --> [7:CONNECT]
Oct 16 16:48:14.35: [  499]: SEND begin page
Oct 16 16:48:14.37: [  499]: <-- data [1026]
Oct 16 16:48:14.38: [  499]: <-- data [1036]
Oct 16 16:48:14.38: [  499]: <-- data [1027]
Oct 16 16:48:14.38: [  499]: <-- data [1024]
Oct 16 16:48:16.37: [  499]: <-- data [1031]
Oct 16 16:48:16.37: [  499]: <-- data [1027]
Oct 16 16:48:16.38: [  499]: <-- data [1028]
Oct 16 16:48:16.38: [  499]: <-- data [1024]
Oct 16 16:48:18.43: [  499]: <-- data [1026]
Oct 16 16:48:21.86: [  499]: <-- data [1024]
Oct 16 16:48:23.68: [  499]: <-- data [1027]
Oct 16 16:48:23.69: [  499]: <-- data [1030]
Oct 16 16:48:25.66: [  499]: <-- data [1030]
Oct 16 16:48:25.67: [  499]: <-- data [1025]
Oct 16 16:48:28.43: [  499]: <-- data [1026]
Oct 16 16:48:28.43: [  499]: <-- data [1027]
Oct 16 16:48:30.80: [  499]: <-- data [1027]
Oct 16 16:48:30.80: [  499]: <-- data [1026]
Oct 16 16:48:32.34: [  499]: <-- data [1030]
Oct 16 16:48:34.09: [  499]: <-- data [1027]
Oct 16 16:48:34.10: [  499]: <-- data [1033]
Oct 16 16:48:36.24: [  499]: <-- data [1029]
Oct 16 16:48:38.11: [  499]: <-- data [1030]
Oct 16 16:48:38.12: [  499]: <-- data [730]
Oct 16 16:48:38.12: [  499]: SENT 24281 bytes of data
Oct 16 16:48:38.12: [  499]: SEND 1D RTC
Oct 16 16:48:38.12: [  499]: <-- data [9]
Oct 16 16:48:38.12: [  499]: SEND end page
Oct 16 16:48:38.12: [  499]: SEND send EOP (no more pages or documents)
Oct 16 16:48:38.12: [  499]: <-- data [2]
Oct 16 16:48:53.72: [  499]: --> [7:+FHS:51]
Oct 16 16:48:53.72: [  499]: REMOTE HANGUP: RSPREC error/got DCN (code 51)
Oct 16 16:48:53.72: [  499]: <-- [5:ATH0\r]
Oct 16 16:48:53.84: [  499]: --> [2:OK]
Oct 16 16:48:53.84: [  499]: SESSION END




On Sat, 17 Oct 1998, you wrote:
>> 
>> After successfully transmitting about 70 percent of a document the remote
>> fax hangs and returns the following error.
>
>It would be significant to know if it stops between pages - the following
>would imply it would.
>
>> RSPREC error/got DCN
>
>Your unspecified Class 1 modem reported that the unspecified remote
>modem/machine had prematurely disconnected whilst training the high
>speed part of the modem in preparation for receiving the page you
>were sending.
>
>It is unlikely that there is a problem with your unspecified version of
>Hylafax or your unspecified operating system and more likely that the
>modem, remote machine, or phone line are unreliable.  However, if it
>was, the unsupplied protocol trace would be needed to diagnose it.
>
>> I have looked for this in the documentation but I don't see it.
>
>DCN will be documented in the IEE spec for Class 1 fax modems.  Documentation
>used here was the source code comments, after grepping for the error message.