flexfax: Unspecified Transmit Phase B error

["Mike Pelley" <mike@pelley.com>]

Hello - I've seen this error in the archives quite a few times and tried a
few of the solutions offered with no success.  I am using NetBSD 1.3.2/i386
and Hylafax 4.0 pl 2, with a Cardinal Connecta 56K D/F Model 3440.

Currently, I can receive faxes with no problems but I cannot send faxes.  My
log file is attached at the end of this message, and my SessionTracing is
set to 15.  It appears that there is some garbage near the fatal disconnect,
although perhaps that's a byproduct of the hangup.  I tried changing rtscts
to xonxoff with no luck (log file is very similar).  Also, I tried the line:

Class2DDISCmd:          AT+FDIS         # enable workaround for broken +FDIS

in my config file but then the log dies with:

Sep 14 16:57:54.24: [ 1355]: <-- [24:AT+FDIS=0,5,0,2,0,0,0,0\r]
Sep 14 16:57:54.47: [ 1355]: --> [5:ERROR]

Any help is greatly appreciated - I'm a bit stuck now  ;o)

Thanks!  Mike.


Current Log File:

Sep 14 17:02:57.17: [ 1435]: SESSION BEGIN 00000065 8372938
Sep 14 17:02:57.17: [ 1435]: SEND FAX: JOB 9 DEST 8372938 COMMID 00000065
Sep 14 17:02:57.17: [ 1435]: MODEM set DTR OFF
Sep 14 17:02:57.17: [ 1435]: DELAY 2600 ms
Sep 14 17:02:59.77: [ 1435]: MODEM set DTR ON
Sep 14 17:02:59.77: [ 1435]: MODEM set baud rate: 38400 baud, input flow
RTS/CTS, output flow RTS/CTS
Sep 14 17:02:59.77: [ 1435]: MODEM flush i/o
Sep 14 17:02:59.77: [ 1435]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 14 17:02:59.90: [ 1435]: --> [2:OK]
Sep 14 17:02:59.90: [ 1435]: <-- [27:ATS8=2S7=60&H1&I0&R2&D3&C1\r]
Sep 14 17:03:00.03: [ 1435]: --> [2:OK]
Sep 14 17:03:00.03: [ 1435]: <-- [14:AT+FCLASS=2.0\r]
Sep 14 17:03:00.16: [ 1435]: --> [2:OK]
Sep 14 17:03:00.16: [ 1435]: <-- [9:AT+FLO=2\r]
Sep 14 17:03:00.29: [ 1435]: --> [2:OK]
Sep 14 17:03:00.29: [ 1435]: <-- [9:AT+FPP=0\r]
Sep 14 17:03:00.42: [ 1435]: --> [2:OK]
Sep 14 17:03:00.42: [ 1435]: <-- [9:AT+FBO=0\r]
Sep 14 17:03:00.55: [ 1435]: --> [2:OK]
Sep 14 17:03:00.55: [ 1435]: <-- [10:AT+FCT=30\r]
Sep 14 17:03:00.68: [ 1435]: --> [2:OK]
Sep 14 17:03:00.68: [ 1435]: <-- [15:AT+FNR=1,1,1,1\r]
Sep 14 17:03:00.81: [ 1435]: --> [2:OK]
Sep 14 17:03:00.81: [ 1435]: <-- [9:AT+FIE=0\r]
Sep 14 17:03:00.94: [ 1435]: --> [2:OK]
Sep 14 17:03:00.94: [ 1435]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Sep 14 17:03:01.08: [ 1435]: --> [2:OK]
Sep 14 17:03:01.08: [ 1435]: <-- [7:ATL0M1\r]
Sep 14 17:03:01.20: [ 1435]: --> [2:OK]
Sep 14 17:03:01.20: [ 1435]: MODEM input buffering enabled
Sep 14 17:03:01.22: [ 1435]: <-- [14:AT+FCLASS=2.0\r]
Sep 14 17:03:01.45: [ 1435]: --> [2:OK]
Sep 14 17:03:01.45: [ 1435]: <-- [9:AT+FLO=2\r]
Sep 14 17:03:01.68: [ 1435]: --> [2:OK]
Sep 14 17:03:01.68: [ 1435]: <-- [9:AT+FPP=0\r]
Sep 14 17:03:01.91: [ 1435]: --> [2:OK]
Sep 14 17:03:01.91: [ 1435]: <-- [9:AT+FBO=0\r]
Sep 14 17:03:02.13: [ 1435]: --> [2:OK]
Sep 14 17:03:02.13: [ 1435]: <-- [10:AT+FCT=30\r]
Sep 14 17:03:02.35: [ 1435]: --> [2:OK]
Sep 14 17:03:02.35: [ 1435]: <-- [15:AT+FNR=1,1,1,1\r]
Sep 14 17:03:02.58: [ 1435]: --> [2:OK]
Sep 14 17:03:02.58: [ 1435]: <-- [9:AT+FIE=0\r]
Sep 14 17:03:02.80: [ 1435]: --> [2:OK]
Sep 14 17:03:02.80: [ 1435]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Sep 14 17:03:03.03: [ 1435]: --> [2:OK]
Sep 14 17:03:03.03: [ 1435]: <-- [10:AT+FLI=""\r]
Sep 14 17:03:03.26: [ 1435]: --> [2:OK]
Sep 14 17:03:03.28: [ 1435]: DIAL 7283756
Sep 14 17:03:03.28: [ 1435]: <-- [13:ATDT8372938@\r]
Sep 14 17:03:27.42: [ 1435]: --> [4:+FCO]
Sep 14 17:03:30.54: [ 1435]: --> [39:+FNF:ESC+FCI:"
6138372938"^T+FIS:]
Sep 14 17:03:30.54: [ 1435]: REMOTE NSF "ESC+FCI:"
6138372938"^T+FIS:"
Sep 14 17:03:30.54: [ 1435]: --> [17:,5,0,2,1,0,0,4<A0>lV]
Sep 14 17:03:30.89: [ 1435]: --> [8:<A0>lV<A0>lVQQ]
Sep 14 17:03:31.19: [ 1435]: -->
[79:QQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQE<BB><9A><A5><C7><CC>S
D<AB>
r<E2>5'B^Wv<C6><E1>B^D<94><A7>G|^^<93><97>/~]
Sep 14 17:03:31.19: [ 1435]: -->
[54:G<85>^W#<F3>^G<CF>T<F1><BD><FA><E3><C4>J^B^DS%Lv<96><B6>5<85><BC><8F>g<9
5>B
<EF><82><FF>|^B<D2><FF><FF><FF> <FF>SCnd   ^D^A<FF>^B <<FF>]
Sep 14 17:03:31.30: [ 1435]: --> [1: ]
Sep 14 17:03:31.30: [ 1435]: REMOTE HANGUP: Unspecified Transmit Phase B
error (code 20)
Sep 14 17:03:31.30: [ 1435]: SEND FAILED: Unspecified Transmit Phase B error
Sep 14 17:03:31.30: [ 1435]: <-- [5:ATH0\r]
Sep 14 17:03:31.30: [ 1435]: --> [2:OK]
Sep 14 17:03:31.30: [ 1435]: MODEM set DTR OFF
Sep 14 17:03:31.31: [ 1435]: SESSION END