flexfax: Problem : any idea ?

[coppelli@sun3.dsea.unipi.it (Alessandro Coppelli)]

 Hi to all.
 
  SCENARIO
  ========
  
   Linux box with USR Sportster modem/fax and latest Hylafax 
   
 PROBLEM
 =======
 
 
 
>Your facsimile job to 0,,055,367583 failed because:
>    Unspecified Transmit Phase C error; too many attempts to send
>
>    ---- Transcript of session follows ----
>
>May 21 13:12:41.90: [25709]: SESSION BEGIN 00000021 39055367583
>May 21 13:12:41.92: [25709]: SEND FAX: JOB 75 DEST 0,,055,367583 COMMID 
00000021
>May 21 13:12:41.92: [25709]: DELAY 2600 ms
>May 21 13:12:44.53: [25709]: <-- [15:ATE0V1Q0S0=0H0\r]
>May 21 13:12:44.66: [25709]: --> [2:OK]
>May 21 13:12:44.66: [25709]: <-- [21:ATS8=2S7=60&K3&D2&C1\r]
>May 21 13:12:44.80: [25709]: --> [2:OK]
>May 21 13:12:44.80: [25709]: <-- [12:AT+FCLASS=1\r]
>May 21 13:12:44.94: [25709]: --> [2:OK]
>May 21 13:12:44.94: [25709]: <-- [5:ATM0\r]
>May 21 13:12:45.08: [25709]: --> [2:OK]
>May 21 13:12:45.09: [25709]: <-- [12:AT+FCLASS=1\r]
>May 21 13:12:45.32: [25709]: --> [2:OK]
>May 21 13:12:45.33: [25709]: DIAL 0,,055,367583
>May 21 13:12:45.33: [25709]: <-- [19:ATDT0,,055,367583@\r]
>May 21 13:13:10.21: [25709]: --> [7:CONNECT]
>May 21 13:13:10.52: [25709]: --> [2:OK]
>May 21 13:13:10.52: [25709]: <-- [9:AT+FRH=3\r]
>May 21 13:13:10.54: [25709]: --> [7:CONNECT]
>May 21 13:13:10.83: [25709]: --> [2:OK]
>May 21 13:13:10.83: [25709]: REMOTE CSI "055367583"
>May 21 13:13:10.83: [25709]: <-- [9:AT+FRH=3\r]
>May 21 13:13:10.86: [25709]: --> [7:CONNECT]
>May 21 13:13:11.10: [25709]: --> [2:OK]
>May 21 13:13:11.10: [25709]: REMOTE best rate 9600 bit/s
>May 21 13:13:11.10: [25709]: REMOTE max page width 1728 pixels in 215 mm
>May 21 13:13:11.11: [25709]: REMOTE max unlimited page length 
>May 21 13:13:11.11: [25709]: REMOTE best vres 7.7 line/mm
>May 21 13:13:11.11: [25709]: REMOTE best format 1-D MR
>May 21 13:13:11.11: [25709]: REMOTE best 20 ms, 10 ms/scanline
>May 21 13:13:11.11: [25709]: USE 9600 bit/s
>May 21 13:13:11.11: [25709]: USE 20 ms, 10 ms/scanline
>May 21 13:13:11.11: [25709]: SEND file "docq/doc58.ps;01"
>May 21 13:13:11.11: [25709]: USE page width 1728 pixels in 215 mm
>May 21 13:13:11.11: [25709]: USE unlimited page length 
>May 21 13:13:11.11: [25709]: USE 7.7 line/mm
>May 21 13:13:11.11: [25709]: USE 1-D MR
>May 21 13:13:11.11: [25709]: SEND training at v.29 9600 bit/s
>May 21 13:13:11.11: [25709]: <-- [9:AT+FTH=3\r]
>May 21 13:13:11.15: [25709]: --> [7:CONNECT]
>May 21 13:13:12.65: [25709]: --> [7:CONNECT]
>May 21 13:13:13.15: [25709]: --> [2:OK]
>May 21 13:13:13.15: [25709]: DELAY 75 ms
>May 21 13:13:13.24: [25709]: <-- [10:AT+FTM=96\r]
>May 21 13:13:13.57: [25709]: --> [7:CONNECT]
>May 21 13:13:15.20: [25709]: --> [2:OK]
>May 21 13:13:15.20: [25709]: <-- [9:AT+FRH=3\r]
>May 21 13:13:16.45: [25709]: --> [7:CONNECT]
>May 21 13:13:16.60: [25709]: --> [2:OK]
>May 21 13:13:16.60: [25709]: TRAINING succeeded
>May 21 13:13:16.60: [25709]: <-- [10:AT+FTM=96\r]
>May 21 13:13:16.94: [25709]: --> [7:CONNECT]
>May 21 13:13:16.94: [25709]: SEND begin page
>May 21 13:13:31.03: [25709]: SENT 27495 bytes of data
>May 21 13:13:45.07: [25709]: SENT 27486 bytes of data
>May 21 13:13:49.40: [25709]: SENT 9463 bytes of data
>May 21 13:13:49.40: [25709]: SEND 1D RTC
>May 21 13:13:49.41: [25709]: SEND end page
>May 21 13:15:09.40: [25709]: <-- [9:AT+FTH=3\r]
>May 21 13:15:11.95: [25709]: --> [0:]
>May 21 13:15:11.96: [25709]: SEND FAILED: Unspecified Transmit Phase C error; 
too many attempts to send
>May 21 13:15:11.96: [25709]: <-- [5:ATH0\r]
>May 21 13:15:16.95: [25709]: MODEM <Timeout>
>May 21 13:15:16.97: [25709]: SESSION END
>
>    ---- Unsent job status ----


 What happaned ? Any idea ?
 
 Alessandro