flexfax: Phase B Error - Code 20

[Olaf Jaeger <ojaeger@ul.psi.de>]

Hi,

Im using Hylafax 4.0pl1 on a Linux 2.0.29 kernel with a "Creatix SG2834
turbo" modem (it has a Rockwell chipset).

The output below shows the log when trying to fax a mail coming through
the faxmail interface. The mail contained an attached postscript file
with type "postscipt" and encoding "MIME postscript".
.
Im using Pegasus mail (32-bit) with windows NT 4.0 workstation. The ps
file was generated by MS WinWord with an Apple Laserwriter driver.
The resulting ps file produced by faxmail looks ok and could be printed
on a
postscript printer. The printout contains the attached text only, no
mail header.

During fax operation the modem seems to get too large lines, so ist
refused further processing. When I strip off the faxmail generated
postscript frame an try to fax the bare ps attachment everything works
fine.

--------- (from hylafax log...) ---------

Sep 10 15:00:57.44: [ 1780]: SESSION BEGIN 00000277 4930xxxxxxxx
Sep 10 15:00:57.47: [ 1780]: SEND FAX: JOB 190 DEST xxxxxxxx COMMID
00000277
Sep 10 15:00:57.47: [ 1780]: DELAY 2600 ms
Sep 10 15:01:00.08: [ 1780]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 10 15:01:00.10: [ 1780]: --> [2:OK]
Sep 10 15:01:00.10: [ 1780]: <-- [21:ATS8=2S7=60&K3&D3&C1\r]
Sep 10 15:01:00.12: [ 1780]: --> [2:OK]
Sep 10 15:01:00.12: [ 1780]: <-- [12:AT+FCLASS=2\r]
Sep 10 15:01:00.13: [ 1780]: --> [2:OK]
Sep 10 15:01:00.13: [ 1780]: <-- [10:AT+FTBC=0\r]
Sep 10 15:01:00.14: [ 1780]: --> [2:OK]
Sep 10 15:01:00.14: [ 1780]: <-- [10:AT+FBOR=0\r]
Sep 10 15:01:00.15: [ 1780]: --> [2:OK]
Sep 10 15:01:00.15: [ 1780]: <-- [13:AT+FPHCTO=30\r]
Sep 10 15:01:00.16: [ 1780]: --> [2:OK]
Sep 10 15:01:00.16: [ 1780]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Sep 10 15:01:00.18: [ 1780]: --> [2:OK]
Sep 10 15:01:00.18: [ 1780]: <-- [5:ATM0\r]
Sep 10 15:01:00.19: [ 1780]: --> [2:OK]
Sep 10 15:01:00.31: [ 1780]: <-- [12:AT+FCLASS=2\r]
Sep 10 15:01:00.43: [ 1780]: --> [2:OK]
Sep 10 15:01:00.43: [ 1780]: <-- [10:AT+FTBC=0\r]
Sep 10 15:01:00.54: [ 1780]: --> [2:OK]
Sep 10 15:01:00.54: [ 1780]: <-- [10:AT+FBOR=0\r]
Sep 10 15:01:00.65: [ 1780]: --> [2:OK]
Sep 10 15:01:00.65: [ 1780]: <-- [13:AT+FPHCTO=30\r]
Sep 10 15:01:00.76: [ 1780]: --> [2:OK]
Sep 10 15:01:00.76: [ 1780]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Sep 10 15:01:00.88: [ 1780]: --> [2:OK]
Sep 10 15:01:00.88: [ 1780]: <-- [31:AT+FLID="xxxxxxxxxxxxxxxxx"\r]
Sep 10 15:01:01.00: [ 1780]: --> [2:OK]
Sep 10 15:01:01.06: [ 1780]: DIAL xxxxxxxx
Sep 10 15:01:01.06: [ 1780]: <-- [17:ATX3DT0Wxxxxxxxx\r]
Sep 10 15:01:14.18: [ 1780]: --> [5:+FCON]
Sep 10 15:01:16.95: [ 1780]: --> [29:+FCSI: "   +49 30  xxxx xxxx"]
Sep 10 15:01:17.00: [ 1780]: REMOTE CSI "+49 30  xxxx xxxx"
Sep 10 15:01:17.35: [ 1780]: --> [22:+FDIS: 1,3,0,2,1,0,0,4]
Sep 10 15:01:17.35: [ 1780]: --> [2:OK]
Sep 10 15:01:17.35: [ 1780]: REMOTE best rate 9600 bit/s
Sep 10 15:01:17.35: [ 1780]: REMOTE max page width 1728 pixels in 215 mm

Sep 10 15:01:17.35: [ 1780]: REMOTE max unlimited page length
Sep 10 15:01:17.35: [ 1780]: REMOTE best vres 7.7 line/mm
Sep 10 15:01:17.35: [ 1780]: REMOTE best format 2-D MR
Sep 10 15:01:17.35: [ 1780]: REMOTE best 20 ms, 10 ms/scanline
Sep 10 15:01:17.35: [ 1780]: USE 9600 bit/s
Sep 10 15:01:17.35: [ 1780]: USE 20 ms, 10 ms/scanline
Sep 10 15:01:17.36: [ 1780]: SEND file "docq/doc190.ps;30"
Sep 10 15:01:17.59: [ 1780]: Modem does not support document page width,

max page width 2432 pixels, image width 1686 pixels
Sep 10 15:01:17.59: [ 1780]: <-- [5:ATH0\r]
Sep 10 15:01:17.85: [ 1780]: --> [9:+FHNG: 20]
Sep 10 15:01:17.85: [ 1780]: REMOTE HANGUP: Unspecified Transmit Phase B
error (code 20)
Sep 10 15:01:18.43: [ 1780]: --> [2:OK]
Sep 10 15:01:18.43: [ 1780]: SESSION END

-------- (end of log) ------------------

I already set "Use2D : No" and "PageChop : No" in etc/config which
solves some former problems but unfortunaly not this one.

Any ideas what could be wrong ?


Thanks for help.
(Please answer by mail, because I didnt subscribe to the maillist.)


Olaf