5:ERROR, [64:^S^Q^S^Q^S^Q

["Roman Pavlik" <rpav@www.cz>]

Hi,

I ask you for help with "5:ERROR" mesage. I try to reconfig our modem to be
a Class 2.0, and in log file appears:

Mar 25 12:36:56.54: [ 1178]: <-- data [1034]
Mar 25 12:36:57.48: [ 1178]: <-- data [326]
Mar 25 12:36:58.91: [ 1178]: SENT 26950 bytes of data
Mar 25 12:36:58.91: [ 1178]: <-- data [2]
Mar 25 12:37:00.36: [ 1178]: SEND end page
Mar 25 12:37:12.35: [ 1178]: -->
[64:^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q]
Mar 25 12:37:12.35: [ 1178]: --> [2:OK]
Mar 25 12:37:12.35: [ 1178]: SEND send MPS (more pages, same document)
Mar 25 12:37:12.35: [ 1178]: <-- [9:AT+FET=0\r]
Mar 25 12:37:15.60: [ 1178]: --> [7:+FPTS:2]
Mar 25 12:37:15.60: [ 1178]: --> [2:OK]
Mar 25 12:37:15.60: [ 1178]: SEND recv RTN (retrain negative)
Mar 25 12:37:15.60: [ 1178]: <-- [7:AT+FDT\r]


The "^S^Q" line look like a try of xonxoff mesage, isn't it? I configure
ttyf2 on my SGI IRIX 6.2, the /var/spool/fax/etc/config:

CountryCode:            420
AreaCode:               5
FAXNumber:              +420.5.41245982
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          low
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "SkyNet, s.r.o."
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
NoCarrierRetrys:        3
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 2 interface
ModemRate:              38400           # 38.4 works fine
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&H0           # disable flow control
ModemHardFlowCmd:       AT&H3           # hardware flow control
ModemSoftFlowCmd:       AT&H4           # software flow control
ModemSetupDTRCmd:       AT&D2           # DTR off causes modem to hang up
ModemSetupDCDCmd:       AT&C1           # DCD tracks carrier
ModemSetupAACmd:        AT+FAA=1        # enable in current class
#
ModemSendFillOrder:     LSB2MSB         # as expected
ModemRecvFillOrder:     MSB2LSB         # opposite of what makes sense
Class2RecvDataTrigger:  "\022"          # a la 2388-B
#
# Additional reset commands:
#
# &B1     DTE-DCE rate is fixed at DTE setting
# &N0     Auto-negotiate highest possible DCE-DCE link rate
# &S0     DSR always on
# *F0     Deny remote configuration
# S18=2   Receive at 38400
# S38.3=1 DCD on/off sequence follows UNIX standard; also
#         fix receiving baud rate at S18 value
# S39=0   (avoid Class 2 compatibility hacks)
#
ModemResetCmds:         AT&B1&N0&S0*F0S18=2S38.3=1S39=0
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# Unfortunately, ZyXEL's don't seem to detect a busy signal when
# the @ symbol is used to terminate the dialing string.  Instead
# calls to a busy line come back with a NO CARRIER status which
# causes us to toss the job.  Consequently we fall back to the
# normal method and raise the number of retries on a no carrier
# status.  ZyXEL claims that this behaviour is not a bug, but
# rather that we are requesting ``an enhancement'' (never mind
# that their manual says that it should work).
#
ModemDialCmd:           ATDP%s          # no '@' 'cuz then busy not recognized
NoCarrierRetrys:        3               # retry 3 times on no carrier
#
ModemSetVolumeCmd:      "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
#
# Caller ID configuration setup.
#
#QualifyCID:            etc/cid         # CID access control list file
#CIDNumber:             "CALLER NUMBER: " # pattern string for phone number
info#CIDName:               "CALLER NAME: " # pattern string for identity info
#
PagerSetupCmds:         AT&K0&N15       # use V.22 at 1200 bps (PageNet)
#
# Rev 6.1x firmware have a bug in the ECM support so
# explicitly disable it's use.  To re-enable its use just
# comment out the following line.
#
Class2DCCQueryCmd:      "!(0,1),(0-5),(0-4),(0-2),(0,1),(0),(0),(0-7)"


Thank you for your help.



-- 
Roman Pavlik       e-mail:Roman.Pavlik@www.cz
                   http://www.cz
SkyNet, s.r.o.     TIS Authorized Security Partner
Kabatnikova 5      tel: +420 5 41 24 59 79 
602 00 Brno        fax: +420 5 41 24 59 82
Czech Republic