USR Sport 33.6

[Roman Pavlik <Roman.Pavlik@www.cz>]

Hi,

we are using hylafax 4.0pl1 on IRIX 6.2. We use US Robotics Sport 33.6
It's connected to ttym2 (the file /var/spool/fax/etc/config.ttym2 is
attached).

I've troble when sending fax. The outgoing fax is OK, notify OK,
but "I don't know who" do not restart /usr/local/sbin/faxgetty ttym2
so the faxmodem do not detected TR and are not able to receive fax.

when I kill faxgetty it's "respawn" and everything looks OK.

line in inittab:
t2:23:respawn:/usr/local/sbin/faxgetty ttym2

the file /var/spool/fax/etc/config.ttym2 (we us it as Class 1 modem):
CountryCode:            42      
AreaCode:               5
FAXNumber:              +42.5.41245982
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          low
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "SkyNet, s.r.o."
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
#QualifyTSI:            etc/tsi
MaxRecvPages:           25
ModemType:              Class1          # use class 1 interface
ModemRate:              38400           # DCE-DTE communication rate
ModemFlowControl:       xonxoff         # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow
control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)ModemResultCodesCmd:    ATQ0X3          # enable extended result
codes
#ModemDialCmd:           ATDP%s@
ModemDialCmd:           ATDP%s
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1TCFResponseDelay: 75              # 75ms delay between recv TCF &
responseClass1SendPPMDelay:     75              # 75ms delay before
sending PPM
Class1SendTCFDelay:     75              # 75ms delay between sending DCS
& TCF
Class1TrainingRecovery: 1500            # 1.5sec delay after training
failure
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident
frames
Class1TCFMaxNonZero:    10              # max 10% of data may be
non-zero
Class1TCFMinRun:        1000 



Thank you very much for help........


Roman Pavlik       e-mail:Roman.Pavlik@www.cz
                   http://www.cz
SkyNet, s.r.o.    
Kabatnikova 5      tel: +42 5 41 24 59 79 
602 00 Brno        fax: +42 5 41 24 59 82
Czech Republic