[hylafax-devel] AT&T DataPort Express config

[Tim Rice <tim@trr.metro.net>]

Here is a new config file for the AT&T DataPort Express in class 2 mode

# $Id: att-dpexpress-2,v 1.3 2000/05/26 22:37:10 tim Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 2 command interface with
# an AT&T DataPort Express 14.4 modem. Model 3715-A1-202
# Firmware version (ati1)	FW Level 091394    Checksum 182050 V1.15.07 SA
# or newer.
#
# Hardware flow control is used by default.
#
# CONFIG: CLASS2: AT?T*PARADYNE*-ROCKWELL*144DPI*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		38400		# set rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
ModemHardFlowCmd:	AT&R0\D1\Q3	# use RTS/CTS and enable RS232 handling
ModemSoftFlowCmd:	AT&R1\D0\Q1	# use RTS/CTS and enable RS232 handling
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
ModemSetupAACmd:	AT+FAA=1	# enable adaptive-answer in Class 2
#
ModemRecvFillOrder:	MSB2LSB		# bit order of received facsimile
ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
ModemDialCmd:		ATDT%s		# T for tone dialing
#
# Chip locks the line rate and switches to xon/xoff flow
# control when receiving facsimile--we must follow suit.
#
ModemAnswerFaxBeginCmd:	"<19200><xon>"	# lock line rate & switch flow control
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv
#
# These are known to not be implemented with the above
# firmware rev.  Sending them to the modem does not harm anything,
# but generates an ERROR result that can generate questions from the
# naive--so we disable them here.
#
Class2CQQueryCmd:	AT	# +FAQ=? query for copy quality capabilities
Class2APQueryCmd:	AT	# +FAP=? not supported on this modem
Class2SPLCmd:		AT	# +FSPL= Request to Poll
Class2TBCCmd:           AT	# +FTBC= Phase C Trasmit Data Block Size
Class2PHCTOCmd:		AT	# +FPHCTO= phase C timeout parameter
Class2BugCmd:		AT	# +FBUG= HDLC frame tracing

*** hylafax/distrules.old	Sun Aug 22 21:28:54 1999
--- hylafax/distrules	Fri Jun  2 18:20:02 2000
***************
*** 185,190 ****
--- 185,191 ----
  	config/att-dataport			\
  	config/att-dataport-2			\
  	config/att-dataport-2.0			\
+ 	config/att-dpexpress-2			\
  	config/cirrus				\
  	config/class1				\
  	config/class2				\
*** hylafax/config/Makefile.in.old	Sat May 27 12:00:08 2000
--- hylafax/config/Makefile.in	Fri Jun  2 18:20:02 2000
***************
*** 50,55 ****
--- 50,56 ----
  	att-dataport-2 \
  	att-dataport-2.0 \
  	att-dataport \
+ 	att-dpexpress-2 \
  	cirrus \
  	dsi-scout+ \
  	e-tech \
*** hylafax/pkg/sproto.stub.in.old	Sun Aug 22 21:30:43 1999
--- hylafax/pkg/sproto.stub.in	Fri Jun  2 18:20:02 2000
***************
*** 141,146 ****
--- 141,147 ----
  f none @SPOOL@/config/att-dataport-2=../@SRCDIR@/config/att-dataport-2 0444 @SYSUID@ @SYSGID@
  f none @SPOOL@/config/att-dataport-2.0=../@SRCDIR@/config/att-dataport-2.0 0444 @SYSUID@ @SYSGID@
  f none @SPOOL@/config/att-dataport=../@SRCDIR@/config/att-dataport 0444 @SYSUID@ @SYSGID@
+ f none @SPOOL@/config/att-dpexpress-2=../@SRCDIR@/config/att-dpexpress-2 0444 @SYSUID@ @SYSGID@
  f none @SPOOL@/config/cirrus=../@SRCDIR@/config/cirrus 0444 @SYSUID@ @SYSGID@
  f none @SPOOL@/config/dsi-scout+=../@SRCDIR@/config/dsi-scout+ 0444 @SYSUID@ @SYSGID@
  f none @SPOOL@/config/e-tech=../@SRCDIR@/config/e-tech 0444 @SYSUID@ @SYSGID@


-- 
Tim Rice				Multitalents	(707) 874-1130
tim@trr.metro.net