Personal tools
HylaFAX The world's most advanced open source fax server

HylaFAX Status Codes

Revision as of 19:32, 12 November 2012 by David.mimms (talk | contribs) (Added HylaFAX Status Codes)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

000-049 : call failures

===================================================================

000  : Call successful 001  : Busy signal detected 002  : No carrier detected 003  : No answer from remote 004  : No local dialtone 005  : Invalid dialing command 006  : Unknown problem 007  : Carrier established, but Phase A failure 008  : Data connection established (wanted fax) 009  : Glare - RING detected 010  : Blacklisted by modem 011  : Ringback detected, no answer without CED 012  : Ring detected without successful handshake

050-099 : non Class-specific fax protocol failures

===================================================================

050  : Missing EOL after 5 seconds 051  : Procedure interrupt received, job terminated

100-199 : Class 1-specific protocol failure

===================================================================

100  : Failure to receive silence (synchronization failure). 101  : Failure to raise V.21 transmission carrier. 102  : No sender protocol (T.30 T1 timeout) 103  : RSPREC error/got DCN (sender abort) 104  : RSPREC invalid response received 105  : Failure to train modems 106  : RSPREC error/got EOT 107  : Can not continue after DIS/DTC 108  : COMREC received DCN (sender abort) 109  : No response to RNR repeated 3 times. 110  : COMREC invalid response received 111  : V.21 signal reception timeout; expected page possibly not received in full 112  : Failed to properly detect high-speed data carrier. 113  : Received invalid CTC signal in V.34-Fax. 114  : Failed to properly open V.34 primary channel. 115  : Received premature V.34 termination. 116  : Failed to properly open V.34 control channel. 117  : COMREC invalid response to repeated PPR received 118  : T.30 T2 timeout, expected signal not received 119  : COMREC invalid partial-page signal received 120  : Cannot synchronize ECM frame reception. 121  : ECM page received containing no image data. 122  : Remote has no T.4 receiver capability 123  : DTC received when expecting DIS (not supported) 124  : COMREC error in transmit Phase B/got DCN 125  : COMREC invalid command received/no DIS or DTC 126  : No receiver protocol (T.30 T1 timeout) 127  : Stop and wait failure (modem on hook) 128  : Remote fax disconnected prematurely 129  : Procedure interrupt (operator intervention) 130  : Unable to transmit page (giving up after RTN) 131  : Unable to transmit page (giving up after 3 attempts) 132  : Unable to transmit page (NAK at all possible signalling rates) 133  : Unable to transmit page (NAK with operator intervention) 134  : Fax protocol error (unknown frame received) 135  : Fax protocol error (command repeated 3 times) 136  : DIS/DTC received 3 times; DCS not recognized 137  : Failure to train remote modem at 2400 bps or minimum speed 138  : Receiver flow control exceeded timer. 139  : No response to RR repeated 3 times. 140  : COMREC invalid response received to RR. 141  : No response to CTC repeated 3 times. 142  : COMREC invalid response received to CTC. 143  : Failure to transmit clean ECM image data. 144  : No response to EOR repeated 3 times. 145  : COMREC invalid response received to EOR. 146  : COMREC invalid response received to PPS. 147  : No response to PPS repeated 3 times. 148  : Unable to establish message carrier 149  : Unspecified Transmit Phase C error 150  : No response to MPS repeated 3 tries 151  : No response to EOP repeated 3 tries 152  : No response to EOM repeated 3 tries 153  : No response to PPM repeated 3 tries 154  : Timeout waiting for Phase C carrier drop 155  : PPM received with no image data. To continue risks receipt confirmation.

200-299 : Class 2-specific protocol failure

===================================================================

200  : Unable to request polling operation (modem may not support polling) 201  : Unable to setup polling identifer (modem command failed) 202  : Unable to setup selective polling address (modem command failed) 203  : Unable to setup polling password (modem command failed) 204  : Unable to send password (modem command failed) 205  : Unable to send subaddress (modem command failed) 206  : Unable to restrict minimum transmit speed to %s (modem command failed) 207  : Unable to setup session parameters prior to call (modem command failed) 208  : Unable to set session parameters 209  : 210  : Unknown hangup code 211  : Normal and proper end of connection 212  : Ring detect without successful handshake 213  : Call aborted, from +FK or <CAN> 214  : No loop current 215  : Ringback detected, no answer (timeout) 216  : Ringback detected, no answer without CED 217  : Unspecified Phase A error 218  : No answer (T.30 T1 timeout) 219  : Unspecified Transmit Phase B error 220  : Remote cannot be polled 221  : COMREC error in transmit Phase B/got DCN 222  : COMREC invalid command received/no DIS or DTC 223  : RSPREC error/got DCN 224  : DCS sent 3 times without response 225  : DIS/DTC received 3 times; DCS not recognized 226  : Failure to train at 2400 bps or +FMINSP value 227  : RSPREC invalid response received 228  : Unspecified Transmit Phase C error 229  : Unspecified Image format error 230  : Image conversion error 231  : DTE to DCE data underflow 232  : Unrecognized Transparent data command 233  : Image error, line length wrong 234  : Image error, page length wrong 235  : Image error, wrong compression code 236  : Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command 237  : RSPREC error/got DCN 238  : No response to MPS repeated 3 times 239  : Invalid response to MPS 240  : No response to EOP repeated 3 times 241  : Invalid response to EOP 242  : No response to EOM repeated 3 times 243  : Invalid response to EOM 244  : Unable to continue after PIN or PIP 245  : Unspecified Receive Phase B error 246  : RSPREC error/got DCN 247  : COMREC error 248  : T.30 T2 timeout, expected page not received 249  : T.30 T1 timeout after EOM received 250  : Unspecified Phase C error, including too much delay between TCF and +FDR command 251  : Missing EOL after 5 seconds (section 3.2/T.4) 252  : DCE to DTE buffer overflow 253  : Bad CRC or frame (ECM or BFT modes) 254  : Unspecified Phase D error 255  : RSPREC invalid response received 256  : COMREC invalid response received 257  : Unable to continue after PIN or PIP, no PRI-Q 258  : Command or signal 10 sec. timeout 259  : Cannot send: +FMINSP > remote's +FDIS(BR) code 260  : Cannot send: remote is V.29 only, local DCE constrained to 2400 or 4800 bps 261  : Remote station cannot receive (DIS bit 10) 262  : +FK aborted or <CAN> aborted 263  : +Format conversion error in +FDT=DF,VR, WD,LN Incompatible and inconvertable data format 264  : Remote cannot receive 265  : After +FDR, DCE waited more than 30 seconds for XON from DTE after XOFF from DTE 266  : In Polling Phase B, remote cannot be polled 267-279 (currently unused) 280  : Procedure interrupt (operator intervention) 281  : Unable to transmit page (giving up after RTN) 282  : Unable to transmit page (giving up after 3 attempts) 283  : Unable to transmit page (NAK at all possible signalling rates) 284  : Unable to transmit page (NAK with operator intervention) 285  : Modem protocol error (unknown post-page response) 286  : Batching protocol error 287  : Communication failure during Phase B/C 288  : Communication failure during Phase B/C (modem protocol botch)

300-399 : Non-T.30 client or server failure

===================================================================

301  : Receive aborted due to operator intervention 302  : Problem reading document directory 303  : Internal botch; %s post-page handling string "%s" 304  : Maximum receive page count exceeded, call terminated 305  : Could not fork for local ID. 306  : Bad exit status %#o for '%s' 307  : Could not open a pipe for local ID. 308  : ANSWER: CALL REJECTED 309  : ANSWER: Call deduced as %s, but told to answer as %s; call ignored 310  : External getty use is not permitted {E310} 311  : %s: could not create 312  : "%s: can not fork: %s 313  : ERROR: Unknown status 314  : Can not open document file %s 315  : Can not set directory %u in document file %s 316  : Error reading directory %u in document file %s 317  : Too many pages in submission; max %u 318  : Unable to lock shared document file 319  : Unable to open shared document file 320  : Unable to create document file 321  : Converted document is not valid TIFF 322  : Could not reopen converted document to verify format 323  : Job contains no documents 324  : Modem does not support polling 325  : Kill time expired 326  : Invalid or corrupted job description file 327  : REJECT: Unable to convert dial string to canonical format 328  : REJECT: Requested modem %s is not registered 329  : REJECT: No work found in job file 330  : REJECT: Page width (%u) appears invalid 331  : REJECT: Job expiration time (%u) appears invalid 332  : REJECT: Time-to-send (%u) appears invalid 333  : REJECT: Too many attempts to dial 334  : REJECT: Too many attempts to transmit: %u, max %u 335  : REJECT: Too many pages in submission: %u, max %u 336  : REJECT: Modem is configured as exempt from accepting jobs 337  : Blocked by concurrent calls 338  : Delayed by time-of-day restrictions 339  : Delayed by outbound call staggering 340  : Could not fork to prepare job for transmission 341  : Could not fork to start job transmission 342  : Delayed by prior call 343  : Send program terminated abnormally; unable to exec %s 344  : Job interrupted by user 345  : Call aborted by user 346  : Can not lock modem device 347  : %s [document conversion failure output] 348  : REJECT: %s [JobControl reject notice] 350  : Permission denied (unnacceptable client TSI) 351  : Permission denied (unnacceptable client PWD) 352  : Send aborted due to operator intervention

400-499 : job/modem incompatibility

===================================================================

400  : Modem does not support negotiated signalling rate 401  : Modem does not support negotiated min scanline time 402  : Document is not in a Group 3 or Group 4 compatible format (compression %u) 403  : Document was encoded with 2DMMR, but client does not support this data format 404  : Document was encoded with 2DMMR, but modem does not support this data format 405  : Document was encoded with 2DMMR, but ECM is not being used. 406  : Document was encoded with 2DMR, but client does not support this data format 407  : Document was encoded with 2DMR, but modem does not support this data format 408  : Hyperfine resolution document is not supported by client, image resolution %g x %g lines/mm 409  : Hyperfine resolution document is not supported by modem, image resolution %g x %g lines/mm 410  : Superfine resolution document is not supported by client, image resolution %g lines/mm 411  : Superfine resolution document is not supported by modem, image resolution %g lines/mm 412  : 300x300 resolution document is not supported by client, image resolution %g lines/mm 413  : 300x300 resolution document is not supported by modem, image resolution %g lines/mm 414  : High resolution document is not supported by client, image resolution %g lines/mm 415  : High resolution document is not supported by modem, image resolution %g lines/mm 416  : Client does not support document page width, max remote page width %g pixels, image width %lu pixels 417  : Modem does not support document page width, max page width %g pixels, image width %lu pixels 418  : Client does not support document page length, max remote page length %d mm, image length %lu rows (%.2f mm) 419  : Modem does not support document page length, max page length %s mm, image length %lu rows (%.2f mm) 420  : Unable to configure modem for fax use 421  : Unable to configure modem for data use 422  : Can not setup modem

500-E599 : paging failures

===================================================================

500  : No initial ID response from paging central 501  : Login failed multiple times 502  : Protocol failure: %s from paging central 503  : Protocol failure: %s waiting for go-ahead message 504  : Message block not acknowledged by paging central after multiple tries 505  : Message block transmit failed paging central rejected it 506  : Protocol failure: paging central responded to message block transmit with forced disconnect 507  : Protocol failure: %s to message block transmit 508  : Paging central rejected content; check PIN 509  : Protocol failure: timeout waiting for transaction ACK/NAK from paging central 510  : Paging central responded with forced disconnect 511  : Job has no PIN to send to 512  : No PIN specified

600-699 : Polling failures

===================================================================

601  : remote has no document to poll

900-999  : HylaFAX errors

===================================================================

901  : Unable to open TIFF file %s for writing 902  : Unable to create temp file for received data: %s 903  : Can not set directory in document file 904  : Can not open document file 905  : Internal error: unable to open text message file 906  : Internal error: unable to read text message file 907  : polling operation not done because of internal failure 908  : Write error to file %s



Powered by MediaWiki
Attribution-ShareAlike 2.5

Project hosted by iFAX Solutions