[hylafax-users] Failed to train remote m...

["Gironi Matteo" <m.gironi@xxxxxxxxxxxxxxxx>]

Hi.

 

I’m running Hylafax 4.4.4 under CentOS 5 32bit (Virtual Machine on Oracle Virtual Box), using a Modem Blaster External V.92 modem (faxaddmodem says “Rockbell”).

 

When i try to send a fax to a fax machine it always fail to, and if i run the the command “faxstat -s” it says:

 

JID  PRI  S    Owner Number    Pages Dials TTS Status

16   125  F    root 251       0:1  3:12 Failure to train remote m

 

(i guess it is remote modem or remote machine).

 

Here goes the log:

 

ago 31 17:03:05.62: [ 2687]: SESSION BEGIN 000000020 39055251
ago 31 17:03:05.62: [ 2687]: HylaFAX (tm) Version 4.4.4
ago 31 17:03:05.62: [ 2687]: SEND FAX: JOB 16 DEST 251 COMMID 000000020 DEVICE '/dev/ttyS0' FROM 'm.gironi <m.gironi@xxxxxxxxxxxxxxxx>' USER root
ago 31 17:03:05.62: [ 2687]: <-- [12:AT+FCLASS=1\r]
ago 31 17:03:05.64: [ 2687]: --> [2:OK]
ago 31 17:03:05.64: [ 2687]: DIAL 251
ago 31 17:03:05.64: [ 2687]: <-- [8:ATDT251\r]
ago 31 17:03:24.26: [ 2687]: --> [7:CONNECT]
ago 31 17:03:25.45: [ 2687]: --> [2:OK]
ago 31 17:03:25.45: [ 2687]: REMOTE best rate 14400 bit/s
ago 31 17:03:25.45: [ 2687]: REMOTE max A3 page width (303 mm)
ago 31 17:03:25.45: [ 2687]: REMOTE max unlimited page length
ago 31 17:03:25.45: [ 2687]: REMOTE best vres R16 x 15.4 line/mm
ago 31 17:03:25.45: [ 2687]: REMOTE format support: MH, MR, MMR
ago 31 17:03:25.45: [ 2687]: REMOTE supports T.30 Annex A, 256-byte ECM
ago 31 17:03:25.45: [ 2687]: REMOTE best 0 ms/scanline
ago 31 17:03:25.45: [ 2687]: USE 14400 bit/s
ago 31 17:03:25.45: [ 2687]: USE error correction mode
ago 31 17:03:25.45: [ 2687]: SEND file "docq/doc16.ps;c1"
ago 31 17:03:25.45: [ 2687]: USE A4 page width (215 mm)
ago 31 17:03:25.45: [ 2687]: USE unlimited page length
ago 31 17:03:25.45: [ 2687]: USE 7.7 line/mm
ago 31 17:03:25.45: [ 2687]: USE 2-D MMR
ago 31 17:03:25.45: [ 2687]: USE 0 ms/scanline
ago 31 17:03:25.45: [ 2687]: SEND training at v.17 14400 bit/s
ago 31 17:03:25.45: [ 2687]: <-- [9:AT+FRS=7\r]
ago 31 17:03:25.56: [ 2687]: --> [2:OK]
ago 31 17:03:25.56: [ 2687]: <-- [9:AT+FTH=3\r]
ago 31 17:03:25.60: [ 2687]: --> [7:CONNECT]
ago 31 17:03:25.60: [ 2687]: <-- data [23]
ago 31 17:03:25.60: [ 2687]: <-- data [2]
ago 31 17:03:27.38: [ 2687]: --> [7:CONNECT]
ago 31 17:03:27.38: [ 2687]: <-- data [7]
ago 31 17:03:27.38: [ 2687]: <-- data [2]
ago 31 17:03:27.83: [ 2687]: --> [2:OK]
ago 31 17:03:27.83: [ 2687]: <-- [9:AT+FTS=7\r]
ago 31 17:03:27.92: [ 2687]: --> [2:OK]
ago 31 17:03:27.92: [ 2687]: <-- [11:AT+FTM=145\r]
ago 31 17:03:27.95: [ 2687]: --> [7:CONNECT]
ago 31 17:03:27.95: [ 2687]: <-- data [1024]
ago 31 17:03:27.96: [ 2687]: <-- data [1024]
ago 31 17:03:27.97: [ 2687]: <-- data [652]
ago 31 17:03:27.98: [ 2687]: <-- data [2]
ago 31 17:03:29.65: [ 2687]: --> [2:OK]
ago 31 17:03:29.65: [ 2687]: <-- [9:AT+FRH=3\r]
ago 31 17:03:30.12: [ 2687]: --> [7:CONNECT]
ago 31 17:03:31.00: [ 2687]: --> [2:OK]
ago 31 17:03:31.00: [ 2687]: SEND training at v.17 12000 bit/s
…

…

…

ago 31 17:03:36.63: [ 2687]: SEND training at v.29 9600 bit/s
…

…

…

ago 31 17:03:41.07: [ 2687]: SEND training at v.29 7200 bit/s
…

…

…

ago 31 17:03:45.48: [ 2687]: SEND training at v.27ter 4800 bit/s
…

…

…

ago 31 17:03:50.50: [ 2687]: SEND training at v.27ter fallback mode 2400 bit/s
…

…

…

ago 31 17:03:55.78: [ 2687]: TRAINING failed
ago 31 17:03:55.78: [ 2687]: SEND: Giving up after 3 attempts to send same
page "docq/doc16.ps;c1", dirnum 0
ago 31 17:03:55.78: [ 2687]: <-- [9:AT+FRS=7\r]
ago 31 17:03:55.90: [ 2687]: --> [2:OK]
ago 31 17:03:55.90: [ 2687]: <-- [9:AT+FTH=3\r]
ago 31 17:03:55.94: [ 2687]: --> [7:CONNECT]
ago 31 17:03:55.94: [ 2687]: <-- data [3]
ago 31 17:03:55.94: [ 2687]: <-- data [2]
ago 31 17:03:57.24: [ 2687]: --> [2:OK]
ago 31 17:03:58.24: [ 2687]: <-- [5:ATH0\r]
ago 31 17:03:59.16: [ 2687]: --> [2:OK]
ago 31 17:03:59.16: [ 2687]: SESSION END

 

I also tried to change the modem configuration on ttyS0, now it looks like this:

 

[root@tecnico1 dev]# setserial -a ttyS0

ttyS0, Line 0, UART: 16550A, Port: 0x03f8, IRQ: 4

        Baud_base: 115200, close_delay: 50, divisor: 0

        closing_wait: 3000

        Flags: spd_normal skip_test auto_irq