[hylafax-users] hylafax-4.4.4-1rhel3 and US Robotics 56 EXT faxmodem model 5631

["Robert Becskei" <robert.becskei@xxxxxxxxxxxxxx>]

Dear List,

I'veg to CentOS 3.9
A US Robotics 56K Ext Faxmodem (model 5631) on /dev/ttyS0
I've got hylafax-4.4.4-1rhel3



I can send faxes to our internal fax machine without problems, it arives
every time.


My config for the modem looks like this :

# $Id: class1,v 1.18 2007/03/14 18:24:10 aidan Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            381
AreaCode:               24
FAXNumber:              +38124715898
LongDistancePrefix:     0
InternationalPrefix:    99
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "CaprioloBIKE d.o.o."
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
PercentGoodLines:       0
MaxConsecutiveBadLines: 0
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
#ModemRate:             19200           # rate for DCE-DTE communication
#ModemFlowControl:      xonxoff         # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
#ModemSetupDCDCmd:      AT&C1           # setup so DCD follows carrier
#GettyArgs:             "-h %l dx_%s"   # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:          ATDT%s          # T for tone dialing
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:                ""              # stuff to do when modem is
reset
#ModemAnswerCmd:                ATA             # use this to answer phone
#ModemNoFlowCmd:                AT&K            # disable flow control cmd
#ModemHardFlowCmd:      AT&K3           # hardware flow control cmd
#ModemSoftFlowCmd:      AT&K4           # software flow control cmd
#ModemNoAutoAnswerCmd:  ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:     "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:       ATE0            # disable command echo
#ModemVerboseResultsCmd:        ATV1            # enable verbose command
results
#ModemResultCodesCmd:   ATQ0            # enable result codes
#ModemOnHookCmd:                ATH0            # place phone on hook
(hangup)
#ModemSoftResetCmd:     ATZ             # do soft reset of modem
#ModemSoftResetCmdDelay:        3000    # pause after soft reset
#ModemWaitTimeCmd:      ATS7=60         # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:        ATS8=2          # comma pause time is 2
seconds
#ModemRecvFillOrder:    LSB2MSB         # bit order of received facsimile
#ModemSendFillOrder:    LSB2MSB         # bit order modem expects for
transmit
#
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before
PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before
TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before
EOP
Class1SwitchingCmd:     AT+FRS=7        # silence between HDLC recv and
trans
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF duration

The error I'm getting :

Feb 25 14:39:42.34: [ 1248]: <-- data [2]
Feb 25 14:39:43.17: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:43.17: [ 1248]: <-- data [13]
Feb 25 14:39:43.17: [ 1248]: <-- data [2]
Feb 25 14:39:43.80: [ 1248]: --> [2:OK]
Feb 25 14:39:43.80: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:44.39: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:45.81: [ 1248]: --> [2:OK]
Feb 25 14:39:45.81: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:39:45.81: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:45.86: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:46.21: [ 1248]: --> [2:OK]
Feb 25 14:39:46.21: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:39:46.21: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:46.26: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:46.32: [ 1248]: --> [5:ERROR]
Feb 25 14:39:46.32: [ 1248]: MODEM Command error
Feb 25 14:39:46.32: [ 1248]: FCS error
Feb 25 14:39:46.32: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:39:46.61: [ 1248]: --> [2:OK]
Feb 25 14:39:46.61: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:39:46.69: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:46.69: [ 1248]: <-- data [3]
Feb 25 14:39:46.69: [ 1248]: <-- data [2]
Feb 25 14:39:47.99: [ 1248]: --> [2:OK]
Feb 25 14:39:47.99: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:39:47.99: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:48.41: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:49.64: [ 1248]: --> [2:OK]
Feb 25 14:39:49.64: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:39:49.64: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:49.70: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:50.01: [ 1248]: --> [2:OK]
Feb 25 14:39:50.01: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:39:50.01: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:50.07: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:50.13: [ 1248]: --> [5:ERROR]
Feb 25 14:39:50.13: [ 1248]: MODEM Command error
Feb 25 14:39:50.13: [ 1248]: FCS error
Feb 25 14:39:50.13: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:39:50.42: [ 1248]: --> [2:OK]
Feb 25 14:39:50.42: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:39:50.50: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:50.50: [ 1248]: <-- data [3]
Feb 25 14:39:50.50: [ 1248]: <-- data [2]
Feb 25 14:39:51.80: [ 1248]: --> [2:OK]
Feb 25 14:39:51.80: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:39:51.80: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:52.21: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:53.44: [ 1248]: --> [2:OK]
Feb 25 14:39:53.44: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:39:53.44: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:53.49: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:53.82: [ 1248]: --> [2:OK]
Feb 25 14:39:53.82: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:39:53.82: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:53.87: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:53.94: [ 1248]: --> [5:ERROR]
Feb 25 14:39:53.94: [ 1248]: MODEM Command error
Feb 25 14:39:53.94: [ 1248]: FCS error
Feb 25 14:39:53.94: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:39:54.23: [ 1248]: --> [2:OK]
Feb 25 14:39:54.23: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:39:54.30: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:54.30: [ 1248]: <-- data [3]
Feb 25 14:39:54.30: [ 1248]: <-- data [2]
Feb 25 14:39:55.59: [ 1248]: --> [2:OK]
Feb 25 14:39:55.59: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:39:55.59: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:56.01: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:57.24: [ 1248]: --> [2:OK]
Feb 25 14:39:57.24: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:39:57.24: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:57.30: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:57.61: [ 1248]: --> [2:OK]
Feb 25 14:39:57.61: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:39:57.61: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:57.66: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:57.74: [ 1248]: --> [5:ERROR]
Feb 25 14:39:57.74: [ 1248]: MODEM Command error
Feb 25 14:39:57.74: [ 1248]: FCS error
Feb 25 14:39:57.74: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:39:58.03: [ 1248]: --> [2:OK]
Feb 25 14:39:58.03: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:39:58.11: [ 1248]: --> [7:CONNECT]
Feb 25 14:39:58.11: [ 1248]: <-- data [3]
Feb 25 14:39:58.11: [ 1248]: <-- data [2]
Feb 25 14:39:59.40: [ 1248]: --> [2:OK]
Feb 25 14:39:59.40: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:39:59.40: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:39:59.82: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:01.07: [ 1248]: --> [2:OK]
Feb 25 14:40:01.07: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:40:01.07: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:01.12: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:01.45: [ 1248]: --> [2:OK]
Feb 25 14:40:01.45: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:40:01.45: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:01.50: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:01.56: [ 1248]: --> [5:ERROR]
Feb 25 14:40:01.56: [ 1248]: MODEM Command error
Feb 25 14:40:01.56: [ 1248]: FCS error
Feb 25 14:40:01.56: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:40:01.85: [ 1248]: --> [2:OK]
Feb 25 14:40:01.85: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:40:01.92: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:01.92: [ 1248]: <-- data [3]
Feb 25 14:40:01.92: [ 1248]: <-- data [2]
Feb 25 14:40:03.22: [ 1248]: --> [2:OK]
Feb 25 14:40:03.22: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:40:03.22: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:03.61: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:04.89: [ 1248]: --> [2:OK]
Feb 25 14:40:04.89: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:40:04.89: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:04.95: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:05.27: [ 1248]: --> [2:OK]
Feb 25 14:40:05.27: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:40:05.27: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:05.33: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:05.38: [ 1248]: --> [5:ERROR]
Feb 25 14:40:05.38: [ 1248]: MODEM Command error
Feb 25 14:40:05.38: [ 1248]: FCS error
Feb 25 14:40:05.38: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:40:05.67: [ 1248]: --> [2:OK]
Feb 25 14:40:05.67: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:40:05.75: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:05.75: [ 1248]: <-- data [3]
Feb 25 14:40:05.75: [ 1248]: <-- data [2]
Feb 25 14:40:07.04: [ 1248]: --> [2:OK]
Feb 25 14:40:07.04: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:40:07.04: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:07.45: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:08.69: [ 1248]: --> [2:OK]
Feb 25 14:40:08.69: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:40:08.69: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:08.74: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:09.06: [ 1248]: --> [2:OK]
Feb 25 14:40:09.06: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:40:09.06: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:09.11: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:09.19: [ 1248]: --> [5:ERROR]
Feb 25 14:40:09.19: [ 1248]: MODEM Command error
Feb 25 14:40:09.19: [ 1248]: FCS error
Feb 25 14:40:09.19: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:40:09.48: [ 1248]: --> [2:OK]
Feb 25 14:40:09.48: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:40:09.56: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:09.56: [ 1248]: <-- data [3]
Feb 25 14:40:09.56: [ 1248]: <-- data [2]
Feb 25 14:40:10.85: [ 1248]: --> [2:OK]
Feb 25 14:40:10.85: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:40:10.85: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:11.23: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:12.52: [ 1248]: --> [2:OK]
Feb 25 14:40:12.52: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:40:12.52: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:12.58: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:12.90: [ 1248]: --> [2:OK]
Feb 25 14:40:12.90: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:40:12.90: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:12.95: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:13.01: [ 1248]: --> [5:ERROR]
Feb 25 14:40:13.01: [ 1248]: MODEM Command error
Feb 25 14:40:13.01: [ 1248]: FCS error
Feb 25 14:40:13.01: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:40:13.30: [ 1248]: --> [2:OK]
Feb 25 14:40:13.30: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:40:13.38: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:13.38: [ 1248]: <-- data [3]
Feb 25 14:40:13.38: [ 1248]: <-- data [2]
Feb 25 14:40:14.68: [ 1248]: --> [2:OK]
Feb 25 14:40:14.68: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:40:14.68: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:15.09: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:16.33: [ 1248]: --> [2:OK]
Feb 25 14:40:16.33: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:40:16.33: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:16.38: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:16.70: [ 1248]: --> [2:OK]
Feb 25 14:40:16.70: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:40:16.70: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:16.75: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:16.82: [ 1248]: --> [5:ERROR]
Feb 25 14:40:16.82: [ 1248]: MODEM Command error
Feb 25 14:40:16.82: [ 1248]: FCS error
Feb 25 14:40:16.82: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:40:17.11: [ 1248]: --> [2:OK]
Feb 25 14:40:17.11: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:40:17.19: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:17.19: [ 1248]: <-- data [3]
Feb 25 14:40:17.19: [ 1248]: <-- data [2]
Feb 25 14:40:18.48: [ 1248]: --> [2:OK]
Feb 25 14:40:18.48: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:40:18.48: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:18.89: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:20.13: [ 1248]: --> [2:OK]
Feb 25 14:40:20.13: [ 1248]: RECV recv NSF (non-standard facilities)
Feb 25 14:40:20.13: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:20.19: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:20.50: [ 1248]: --> [2:OK]
Feb 25 14:40:20.50: [ 1248]: RECV recv DIS (identification signal)
Feb 25 14:40:20.50: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:20.55: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:20.62: [ 1248]: --> [5:ERROR]
Feb 25 14:40:20.62: [ 1248]: MODEM Command error
Feb 25 14:40:20.62: [ 1248]: FCS error
Feb 25 14:40:20.62: [ 1248]: <-- [10:AT+FRS=21\r]
Feb 25 14:40:20.90: [ 1248]: --> [2:OK]
Feb 25 14:40:20.90: [ 1248]: <-- [9:AT+FTH=3\r]
Feb 25 14:40:20.98: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:20.98: [ 1248]: <-- data [3]
Feb 25 14:40:20.98: [ 1248]: <-- data [2]
Feb 25 14:40:22.27: [ 1248]: --> [2:OK]
Feb 25 14:40:22.27: [ 1248]: RECV send CRP (command repeat)
Feb 25 14:40:22.27: [ 1248]: <-- [9:AT+FRH=3\r]
Feb 25 14:40:22.74: [ 1248]: --> [7:CONNECT]
Feb 25 14:40:23.69: [ 1248]: --> [2:OK]
Feb 25 14:40:23.69: [ 1248]: RECV recv DCN (disconnect)
Feb 25 14:40:23.69: [ 1248]: RECV FAX: RSPREC error/got DCN (sender abort)
Feb 25 14:40:23.69: [ 1248]: RECV FAX: end
Feb 25 14:40:23.69: [ 1248]: RSPREC error/got DCN (sender abort)
Feb 25 14:40:23.69: [ 1248]: SESSION END

Can someone please help me fix this problem ?

Sincerely
Robert B