 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Hylafax Loopback failing (w/ IAXModem and asterisk)
- To: hylafax-users@xxxxxxxxxxxxxxxxxxxxx
- Subject: [hylafax-users] Hylafax Loopback failing (w/ IAXModem and asterisk)
- From: James Lamanna <jlamanna@xxxxxxxxx>
- Cc: hylafax-users@xxxxxxxxxxx
- Date: Sat, 7 Feb 2009 03:15:06 -0800
Hi,
I'm using sendfax to run a loopback test through my asterisk box back
to Hylafax, however it seems as though I cannot receive the fax.
The call never leaves the asterisk box, but just dials another
IAXModem directly.
Any ideas?
Thanks.
Here's the receive side Hylafax log:
Feb 07 11:07:22.89: [ 1964]: HylaFAX (tm) Version 5.2.8
Feb 07 11:07:23.07: [ 1964]: <-- [4:ATA\r]
Feb 07 11:07:26.80: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:26.80: [ 1964]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyIAX1'
Feb 07 11:07:26.80: [ 1964]: RECV FAX: begin
Feb 07 11:07:26.80: [ 1964]: <-- data [32]
Feb 07 11:07:26.80: [ 1964]: <-- data [2]
Feb 07 11:07:27.76: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:27.76: [ 1964]: <-- data [23]
Feb 07 11:07:27.76: [ 1964]: <-- data [2]
Feb 07 11:07:28.49: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:28.49: [ 1964]: <-- data [13]
Feb 07 11:07:28.49: [ 1964]: <-- data [2]
Feb 07 11:07:29.07: [ 1964]: --> [2:OK]
Feb 07 11:07:29.07: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:29.33: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:30.75: [ 1964]: --> [2:OK]
Feb 07 11:07:30.75: [ 1964]: RECV recv TSI (sender id)
Feb 07 11:07:30.76: [ 1964]: REMOTE TSI "NothingSetup"
Feb 07 11:07:30.76: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:31.09: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:31.14: [ 1964]: --> [2:OK]
Feb 07 11:07:31.14: [ 1964]: RECV recv DCS (command signal)
Feb 07 11:07:31.14: [ 1964]: REMOTE wants 9600 bit/s
Feb 07 11:07:31.14: [ 1964]: REMOTE wants A4 page width (215 mm)
Feb 07 11:07:31.14: [ 1964]: REMOTE wants unlimited page length
Feb 07 11:07:31.14: [ 1964]: REMOTE wants 3.85 line/mm
Feb 07 11:07:31.14: [ 1964]: REMOTE wants 2-D MMR
Feb 07 11:07:31.14: [ 1964]: REMOTE wants T.30 Annex A, 256-byte ECM
Feb 07 11:07:31.14: [ 1964]: RECV training at v.29 9600 bit/s
Feb 07 11:07:31.14: [ 1964]: <-- [10:AT+FRM=96\r]
Feb 07 11:07:35.65: [ 1964]: --> [0:]
Feb 07 11:07:35.65: [ 1964]: MODEM <Empty line>
Feb 07 11:07:35.65: [ 1964]: <-- data [1]
Feb 07 11:07:35.86: [ 1964]: --> [2:OK]
Feb 07 11:07:35.86: [ 1964]: <-- [9:AT+FRS=7\r]
Feb 07 11:07:35.86: [ 1964]: --> [2:OK]
Feb 07 11:07:35.86: [ 1964]: <-- [9:AT+FRS=7\r]
Feb 07 11:07:36.19: [ 1964]: --> [2:OK]
Feb 07 11:07:36.19: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:07:36.31: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:36.31: [ 1964]: <-- data [3]
Feb 07 11:07:36.32: [ 1964]: <-- data [2]
Feb 07 11:07:37.25: [ 1964]: --> [2:OK]
Feb 07 11:07:37.25: [ 1964]: TRAINING failed
Feb 07 11:07:37.26: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:37.52: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:37.55: [ 1964]: --> [5:ERROR]
Feb 07 11:07:37.55: [ 1964]: MODEM Command error
Feb 07 11:07:37.55: [ 1964]: FCS error
Feb 07 11:07:37.55: [ 1964]: <-- [10:AT+FRS=21\r]
Feb 07 11:07:42.08: [ 1964]: --> [2:OK]
Feb 07 11:07:42.08: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:07:42.10: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:42.10: [ 1964]: <-- data [3]
Feb 07 11:07:42.10: [ 1964]: <-- data [2]
Feb 07 11:07:43.17: [ 1964]: --> [2:OK]
Feb 07 11:07:43.17: [ 1964]: RECV send CRP (command repeat)
Feb 07 11:07:43.18: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:43.57: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:44.53: [ 1964]: --> [2:OK]
Feb 07 11:07:44.53: [ 1964]: RECV recv CRP (command repeat)
Feb 07 11:07:44.53: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:07:44.55: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:44.55: [ 1964]: <-- data [32]
Feb 07 11:07:44.56: [ 1964]: <-- data [2]
Feb 07 11:07:46.33: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:46.33: [ 1964]: <-- data [23]
Feb 07 11:07:46.34: [ 1964]: <-- data [2]
Feb 07 11:07:47.07: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:47.07: [ 1964]: <-- data [13]
Feb 07 11:07:47.07: [ 1964]: <-- data [2]
Feb 07 11:07:47.65: [ 1964]: --> [2:OK]
Feb 07 11:07:47.65: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:47.91: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:47.65: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:47.91: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:49.33: [ 1964]: --> [2:OK]
Feb 07 11:07:49.33: [ 1964]: RECV recv TSI (sender id)
Feb 07 11:07:49.34: [ 1964]: REMOTE TSI "NothingSetup"
Feb 07 11:07:49.34: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:49.67: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:49.71: [ 1964]: --> [2:OK]
Feb 07 11:07:49.71: [ 1964]: RECV recv DCS (command signal)
Feb 07 11:07:49.71: [ 1964]: REMOTE wants 7200 bit/s
Feb 07 11:07:49.72: [ 1964]: REMOTE wants A4 page width (215 mm)
Feb 07 11:07:49.72: [ 1964]: REMOTE wants unlimited page length
Feb 07 11:07:49.72: [ 1964]: REMOTE wants 3.85 line/mm
Feb 07 11:07:49.72: [ 1964]: REMOTE wants 2-D MMR
Feb 07 11:07:49.72: [ 1964]: REMOTE wants T.30 Annex A, 256-byte ECM
Feb 07 11:07:49.72: [ 1964]: RECV training at v.29 7200 bit/s
Feb 07 11:07:49.72: [ 1964]: <-- [10:AT+FRM=72\r]
Feb 07 11:07:54.22: [ 1964]: --> [0:]
Feb 07 11:07:54.22: [ 1964]: MODEM <Empty line>
Feb 07 11:07:54.22: [ 1964]: <-- data [1]
Feb 07 11:07:54.43: [ 1964]: MODEM <Timeout>
Feb 07 11:07:54.77: [ 1964]: <-- [9:AT+FRS=7\r]
Feb 07 11:07:54.77: [ 1964]: --> [2:OK]
Feb 07 11:07:54.78: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:07:54.78: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:54.78: [ 1964]: <-- data [3]
Feb 07 11:07:54.78: [ 1964]: <-- data [2]
Feb 07 11:07:54.86: [ 1964]: --> [2:OK]
Feb 07 11:07:54.86: [ 1964]: TRAINING failed
Feb 07 11:07:54.86: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:56.99: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:57.02: [ 1964]: --> [5:ERROR]
Feb 07 11:07:57.02: [ 1964]: MODEM Command error
Feb 07 11:07:57.02: [ 1964]: FCS error
Feb 07 11:07:57.02: [ 1964]: <-- [10:AT+FRS=21\r]
Feb 07 11:07:57.63: [ 1964]: --> [2:OK]
Feb 07 11:07:57.63: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:07:57.65: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:57.66: [ 1964]: <-- data [3]
Feb 07 11:07:57.65: [ 1964]: --> [7:CONNECT]
Feb 07 11:07:57.66: [ 1964]: <-- data [3]
Feb 07 11:07:57.66: [ 1964]: <-- data [2]
Feb 07 11:07:58.73: [ 1964]: --> [2:OK]
Feb 07 11:07:58.73: [ 1964]: RECV send CRP (command repeat)
Feb 07 11:07:58.73: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:07:58.99: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:00.41: [ 1964]: --> [2:OK]
Feb 07 11:08:00.41: [ 1964]: RECV recv TSI (sender id)
Feb 07 11:08:00.42: [ 1964]: REMOTE TSI "NothingSetup"
Feb 07 11:08:00.42: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:08:00.75: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:00.79: [ 1964]: --> [2:OK]
Feb 07 11:08:00.79: [ 1964]: RECV recv DCS (command signal)
Feb 07 11:08:00.79: [ 1964]: REMOTE wants 4800 bit/s
Feb 07 11:08:00.80: [ 1964]: REMOTE wants A4 page width (215 mm)
Feb 07 11:08:00.80: [ 1964]: REMOTE wants unlimited page length
Feb 07 11:08:00.80: [ 1964]: REMOTE wants 3.85 line/mm
Feb 07 11:08:00.80: [ 1964]: REMOTE wants 2-D MMR
Feb 07 11:08:00.80: [ 1964]: REMOTE wants T.30 Annex A, 256-byte ECM
Feb 07 11:08:00.80: [ 1964]: RECV training at v.27ter 4800 bit/s
Feb 07 11:08:00.80: [ 1964]: <-- [10:AT+FRM=48\r]
Feb 07 11:08:05.30: [ 1964]: --> [0:]
Feb 07 11:08:05.30: [ 1964]: MODEM <Empty line>
Feb 07 11:08:05.30: [ 1964]: <-- data [1]
Feb 07 11:08:05.51: [ 1964]: MODEM <Timeout>
Feb 07 11:08:07.01: [ 1964]: <-- [9:AT+FRS=7\r]
Feb 07 11:08:07.01: [ 1964]: --> [2:OK]
Feb 07 11:08:07.01: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:08:07.05: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:07.05: [ 1964]: <-- data [3]
Feb 07 11:08:07.05: [ 1964]: <-- data [2]
Feb 07 11:08:07.28: [ 1964]: --> [2:OK]
Feb 07 11:08:07.28: [ 1964]: TRAINING failed
Feb 07 11:08:07.28: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:08:10.49: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:10.52: [ 1964]: --> [10:NO CARRIER]
Feb 07 11:08:10.52: [ 1964]: MODEM No carrier
Feb 07 11:08:10.52: [ 1964]: <-- [10:AT+FRS=21\r]
Feb 07 11:08:10.68: [ 1964]: --> [2:OK]
Feb 07 11:08:10.68: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:08:10.70: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:10.70: [ 1964]: <-- data [3]
Feb 07 11:08:10.70: [ 1964]: <-- data [2]
Feb 07 11:08:11.76: [ 1964]: --> [2:OK]
Feb 07 11:08:11.76: [ 1964]: RECV send CRP (command repeat)
Feb 07 11:08:11.76: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:08:12.02: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:13.44: [ 1964]: --> [2:OK]
Feb 07 11:08:13.44: [ 1964]: RECV recv TSI (sender id)
Feb 07 11:08:13.44: [ 1964]: REMOTE TSI "NothingSetup"
Feb 07 11:08:13.44: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:08:13.78: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:13.82: [ 1964]: --> [2:OK]
Feb 07 11:08:13.82: [ 1964]: RECV recv DCS (command signal)
Feb 07 11:08:13.82: [ 1964]: REMOTE wants 2400 bit/s
Feb 07 11:08:13.82: [ 1964]: REMOTE wants A4 page width (215 mm)
Feb 07 11:08:13.82: [ 1964]: REMOTE wants unlimited page length
Feb 07 11:08:13.82: [ 1964]: REMOTE wants 3.85 line/mm
Feb 07 11:08:13.82: [ 1964]: REMOTE wants 2-D MMR
Feb 07 11:08:13.82: [ 1964]: REMOTE wants T.30 Annex A, 256-byte ECM
Feb 07 11:08:13.82: [ 1964]: RECV training at v.27ter fallback mode 2400 bit/s
Feb 07 11:08:13.82: [ 1964]: <-- [10:AT+FRM=24\r]
Feb 07 11:08:18.32: [ 1964]: --> [0:]
Feb 07 11:08:18.32: [ 1964]: MODEM <Empty line>
Feb 07 11:08:18.32: [ 1964]: <-- data [1]
Feb 07 11:08:18.53: [ 1964]: MODEM <Timeout>
Feb 07 11:08:21.81: [ 1964]: <-- [9:AT+FRS=7\r]
Feb 07 11:08:21.81: [ 1964]: --> [2:OK]
Feb 07 11:08:21.81: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:08:21.82: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:21.82: [ 1964]: <-- data [3]
Feb 07 11:08:21.82: [ 1964]: <-- data [2]
Feb 07 11:08:22.19: [ 1964]: --> [2:OK]
Feb 07 11:08:22.19: [ 1964]: TRAINING failed
Feb 07 11:08:22.19: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:08:22.42: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:23.00: [ 1964]: --> [5:ERROR]
Feb 07 11:08:23.00: [ 1964]: MODEM Command error
Feb 07 11:08:23.00: [ 1964]: FCS error
Feb 07 11:08:23.00: [ 1964]: <-- [10:AT+FRS=21\r]
Feb 07 11:08:23.69: [ 1964]: --> [2:OK]
Feb 07 11:08:23.69: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:08:23.71: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:23.71: [ 1964]: <-- data [3]
Feb 07 11:08:23.71: [ 1964]: <-- data [2]
Feb 07 11:08:23.91: [ 1964]: --> [2:OK]
Feb 07 11:08:23.91: [ 1964]: RECV send CRP (command repeat)
Feb 07 11:08:23.91: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:08:24.99: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:25.50: [ 1964]: --> [10:NO CARRIER]
Feb 07 11:08:25.50: [ 1964]: MODEM No carrier
Feb 07 11:08:25.50: [ 1964]: <-- [10:AT+FRS=21\r]
Feb 07 11:08:25.75: [ 1964]: --> [2:OK]
Feb 07 11:08:25.75: [ 1964]: <-- [9:AT+FTH=3\r]
Feb 07 11:08:25.76: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:25.76: [ 1964]: <-- data [3]
Feb 07 11:08:25.76: [ 1964]: <-- data [2]
Feb 07 11:08:26.84: [ 1964]: --> [2:OK]
Feb 07 11:08:26.84: [ 1964]: RECV send CRP (command repeat)
Feb 07 11:08:26.84: [ 1964]: <-- [9:AT+FRH=3\r]
Feb 07 11:08:27.10: [ 1964]: --> [7:CONNECT]
Feb 07 11:08:28.06: [ 1964]: --> [2:OK]
Feb 07 11:08:28.06: [ 1964]: RECV recv DCN (disconnect)
Feb 07 11:08:28.06: [ 1964]: RECV FAX: RSPREC error/got DCN (sender
abort) {E103}
Feb 07 11:08:28.06: [ 1964]: RECV FAX: end
Feb 07 11:08:28.06: [ 1964]: RSPREC error/got DCN (sender abort) {E103}
Feb 07 11:08:28.06: [ 1964]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Hylafax Loopback failing (w/ IAXModem and asterisk)
- From: James Lamanna
- Re: [hylafax-users] Hylafax Loopback failing (w/ IAXModem and asterisk)
- Prev by Date: [hylafax-users] not able to send fax from my hylafax server
- Next by Date: [hylafax-users] What do I need to have faxes routed to my email?
- Previous by thread: [hylafax-users] not able to send fax from my hylafax server
- Next by thread: Re: [hylafax-users] Hylafax Loopback failing (w/ IAXModem and asterisk)
- Index(es):
Project hosted by iFAX Solutions