[hylafax-users] failed fax

["Rosario Pingaro" <rpingar@xxxxxxxx>]

I have hylfax on the same machine of asterisk conencted by IAXMODEMS,

 

I have a prticulr destination fax that is failing.

 

Any help to understand the logs??

Thanks

 

 

 

 

  
     Unspecified Transmit Phase C error ; Giving up after 3 attempts to send
same page

    ---- Segue trascrizione della sessione ----




--------------------------------------------------------------------------------


> feb 05 17:11:21.52: [ 1935]: SESSION BEGIN 000001014 56906454238473
> feb 05 17:11:21.52: [ 1935]: HylaFAX (tm) Version 5.2.7
> feb 05 17:11:21.52: [ 1935]: SEND FAX: JOB 493 DEST 56906454238473 COMMID
> 000001014 DEVICE '/dev/ttyIAX18' FROM xxxxxxxxxxxxxx'
> USER mail
> feb 05 17:11:21.52: [ 1935]: STATE CHANGE: RUNNING -> SENDING
> feb 05 17:11:21.52: [ 1935]: <-- [12:AT+FCLASS=1\r]
> feb 05 17:11:21.52: [ 1935]: --> [2:OK]
> feb 05 17:11:21.52: [ 1935]: MODEM set XON/XOFF/FLUSH: input ignored,
> output disabled
> feb 05 17:11:21.60: [ 1935]: 1-D encoding outperforms 2-D by 38%. Prefer
> MH format.
> feb 05 17:11:21.60: [ 1935]: DIAL 56906454238473
> feb 05 17:11:21.60: [ 1935]: <-- [19:ATDT56906454238473\r]
> feb 05 17:11:50.75: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:51.65: [ 1935]: --> [4:12 00 10 03]
> feb 05 17:11:51.65: [ 1935]: --> [5:ERROR]
> feb 05 17:11:51.65: [ 1935]: MODEM Command error
> feb 05 17:11:51.65: [ 1935]: FCS error
> feb 05 17:11:51.65: [ 1935]: <-- [10:AT+FRS=21\r]
> feb 05 17:11:51.99: [ 1935]: --> [2:OK]
> feb 05 17:11:51.99: [ 1935]: <-- [9:AT+FTH=3\r]
> feb 05 17:11:52.01: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:52.01: [ 1935]: <-- HDLC<3:FF C8 D8>
> feb 05 17:11:53.09: [ 1935]: --> [2:OK]
> feb 05 17:11:53.09: [ 1935]: SEND send CRP (command repeat)
> feb 05 17:11:53.09: [ 1935]: <-- [9:AT+FRH=3\r]
> feb 05 17:11:54.47: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:56.03: [ 1935]: --> HDLC<20:FF C0 04 AD 00 51 5A 00 00 00 00
> 00 00 00 00 00 00 00 8D C8>
> feb 05 17:11:56.03: [ 1935]: --> [2:OK]
> feb 05 17:11:56.03: [ 1935]: REMOTE NSF "B5 00 8A 5A 00 00 00 00 00 00 00
> 00 00 00 00"
> feb 05 17:11:56.03: [ 1935]: NSF remote fax equipment: Telogy Networks
> feb 05 17:11:56.03: [ 1935]: <-- [9:AT+FRH=3\r]
> feb 05 17:11:56.81: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:56.81: [ 1935]: --> HDLC<25:FF C0 02 EC 2C 1C CC 4C 2C AC 2C
> 6C 0C 04 9C CC D4 04 04 04 04 04 04 5F F6>
> feb 05 17:11:56.81: [ 1935]: --> [2:OK]
> feb 05 17:11:56.81: [ 1935]: REMOTE CSI "+39 0645423847"
> feb 05 17:11:56.81: [ 1935]: <-- [9:AT+FRH=3\r]
> feb 05 17:11:57.19: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:57.19: [ 1935]: --> HDLC<11:FF C8 01 00 73 15 01 01 C8 CE A9>
> feb 05 17:11:57.23: [ 1935]: --> [2:OK]
> feb 05 17:11:57.23: [ 1935]: REMOTE best rate 9600 bit/s
> feb 05 17:11:57.23: [ 1935]: REMOTE max A4 page width (215 mm)
> feb 05 17:11:57.23: [ 1935]: REMOTE max unlimited page length
> feb 05 17:11:57.23: [ 1935]: REMOTE best vres 300 x 300 dpi
> feb 05 17:11:57.23: [ 1935]: REMOTE format support: MH, MR
> feb 05 17:11:57.23: [ 1935]: REMOTE best 10 ms/scanline
> feb 05 17:11:57.23: [ 1935]: USE 9600 bit/s
> feb 05 17:11:57.23: [ 1935]: SEND file "docq/doc686.tif;f0"
> feb 05 17:11:57.23: [ 1935]: USE A4 page width (215 mm)
> feb 05 17:11:57.23: [ 1935]: USE unlimited page length
> feb 05 17:11:57.23: [ 1935]: USE 3.85 line/mm
> feb 05 17:11:57.23: [ 1935]: USE 1-D MH
> feb 05 17:11:57.23: [ 1935]: USE 10 ms/scanline
> feb 05 17:11:57.23: [ 1935]: SEND training at v.29 9600 bit/s
> feb 05 17:11:57.23: [ 1935]: <-- [9:AT+FRS=7\r]
> feb 05 17:11:57.29: [ 1935]: --> [2:OK]
> feb 05 17:11:57.29: [ 1935]: <-- [9:AT+FTH=3\r]
> feb 05 17:11:57.31: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:57.31: [ 1935]: <-- HDLC<23:FF C0 C2 5E 76 A6 E6 4E A6 6E 76
> F6 C2 04 4E A6 6E 4E A6 CE 1E 86 62>
> feb 05 17:11:58.85: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:58.85: [ 1935]: <-- HDLC<6:FF C8 C1 00 60 14>
> feb 05 17:11:59.21: [ 1935]: --> [2:OK]
> feb 05 17:11:59.21: [ 1935]: <-- [9:AT+FTS=7\r]
> feb 05 17:11:59.31: [ 1935]: --> [2:OK]
> feb 05 17:11:59.31: [ 1935]: MODEM set XON/XOFF/FLUSH: input interpreted,
> output disabled
> feb 05 17:11:59.31: [ 1935]: <-- [10:AT+FTM=96\r]
> feb 05 17:11:59.33: [ 1935]: --> [7:CONNECT]
> feb 05 17:11:59.33: [ 1935]: DELAY 400 ms
> feb 05 17:12:01.27: [ 1935]: --> [2:OK]
> feb 05 17:12:01.27: [ 1935]: MODEM set XON/XOFF/DRAIN: input ignored,
> output disabled
> feb 05 17:12:01.27: [ 1935]: <-- [9:AT+FRH=3\r]
> feb 05 17:12:02.73: [ 1935]: --> [7:CONNECT]
> feb 05 17:12:03.89: [ 1935]: --> HDLC<5:FF C8 22 67 DD>
> feb 05 17:12:03.93: [ 1935]: --> [2:OK]
> feb 05 17:12:03.93: [ 1935]: SEND training at v.29 7200 bit/s
> feb 05 17:12:03.93: [ 1935]: <-- [9:AT+FRS=7\r]
> feb 05 17:12:04.01: [ 1935]: --> [2:OK]
> feb 05 17:12:04.01: [ 1935]: <-- [9:AT+FTH=3\r]
> feb 05 17:12:04.03: [ 1935]: --> [7:CONNECT]
> feb 05 17:12:04.03: [ 1935]: <-- HDLC<23:FF C0 C2 5E 76 A6 E6 4E A6 6E 76
> F6 C2 04 4E A6 6E 4E A6 CE 1E 86 62>
> feb 05 17:12:05.57: [ 1935]: --> [7:CONNECT]
> feb 05 17:12:05.57: [ 1935]: <-- HDLC<6:FF C8 C1 00 70 14>
> feb 05 17:12:05.93: [ 1935]: --> [2:OK]
> feb 05 17:12:05.93: [ 1935]: <-- [9:AT+FTS=7\r]
> feb 05 17:12:06.03: [ 1935]: --> [2:OK]
> feb 05 17:12:06.03: [ 1935]: MODEM set XON/XOFF/FLUSH: input interpreted,
> output disabled
> feb 05 17:12:06.03: [ 1935]: <-- [10:AT+FTM=72\r]
> feb 05 17:12:06.05: [ 1935]: --> [7:CONNECT]
> feb 05 17:12:06.05: [ 1935]: DELAY 400 ms
> feb 05 17:12:07.99: [ 1935]: --> [2:OK]
> feb 05 17:12:07.99: [ 1935]: MODEM set XON/XOFF/DRAIN: input ignored,
> output disabled
> feb 05 17:12:07.99: [ 1935]: <-- [9:AT+FRH=3\r]
> feb 05 17:12:09.51: [ 1935]: --> [7:CONNECT]
> feb 05 17:12:10.67: [ 1935]: --> HDLC<5:FF C8 21 57 BE>
> feb 05 17:12:10.71: [ 1935]: --> [2:OK]
> feb 05 17:12:10.71: [ 1935]: TRAINING succeeded
> feb 05 17:12:10.71: [ 1935]: <-- [9:AT+FRS=7\r]
> feb 05 17:12:10.77: [ 1935]: --> [2:OK]
> feb 05 17:12:10.77: [ 1935]: <-- [10:AT+FTM=72\r]
> feb 05 17:12:10.79: [ 1935]: --> [7:CONNECT]
> feb 05 17:12:10.79: [ 1935]: DELAY 400 ms
> feb 05 17:12:11.19: [ 1935]: MODEM set XON/XOFF/FLUSH: input interpreted,
> output disabled
> feb 05 17:12:11.19: [ 1935]: SEND begin page
> feb 05 17:12:11.25: [ 1935]: Reading MMR-compressed image file
> feb 05 17:12:18.11: [ 1935]: SENT 9481 bytes of data
> feb 05 17:12:28.39: [ 1935]: SENT 9598 bytes of data
> feb 05 17:12:37.55: [ 1935]: SENT 9652 bytes of data
> feb 05 17:12:51.29: [ 1935]: SENT 9585 bytes of data
> feb 05 17:12:59.31: [ 1935]: SENT 9633 bytes of data
> feb 05 17:13:08.47: [ 1935]: SENT 9613 bytes of data
> feb 05 17:13:19.93: [ 1935]: SENT 9619 bytes of data
> feb 05 17:13:31.33: [ 1935]: SENT 9538 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 9628 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 9592 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 9513 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 9605 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 9594 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 9653 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 9660 bytes of data
> feb 05 17:13:36.21: [ 1935]: SENT 7257 bytes of data
> feb 05 17:13:36.21: [ 1935]: SEND 1D RTC
> feb 05 17:13:36.21: [ 1935]: SEND end page
> feb 05 17:13:36.21: [ 1935]: --> [10:NO CARRIER]
> feb 05 17:13:36.21: [ 1935]: MODEM flush i/o
> feb 05 17:13:36.21: [ 1935]: MODEM set XON/XOFF/DRAIN: input ignored,
> output disabled
> feb 05 17:13:36.21: [ 1935]: Unspecified Transmit Phase C error {E149}
> feb 05 17:13:36.21: [ 1935]: SEND: Unspecified Transmit Phase C error
> {E149}; Giving up after 3 attempts to send same page "docq/doc686.tif;f0",
> dirnum 0
> feb 05 17:13:36.21: [ 1935]: <-- [9:AT+FRS=7\r]
> feb 05 17:14:06.21: [ 1935]: MODEM TIMEOUT: reading line from modem
> feb 05 17:14:06.21: [ 1935]: MODEM <Timeout>
> feb 05 17:14:06.21: [ 1935]: Failure to receive silence (synchronization
> failure). {E100}
> feb 05 17:14:06.42: [ 1935]: MODEM TIMEOUT: reading line from modem
> feb 05 17:14:06.42: [ 1935]: MODEM <Timeout>
> feb 05 17:14:06.42: [ 1935]: <-- [9:AT+FTH=3\r]
> feb 05 17:14:13.97: [ 1935]: --> [0:]
> feb 05 17:14:13.97: [ 1935]: MODEM TIMEOUT: sending HDLC frame
> feb 05 17:14:13.97: [ 1935]: MODEM input buffering enabled
> feb 05 17:14:14.97: [ 1935]: <-- [5:ATH0\r]
> feb 05 17:14:19.97: [ 1935]: MODEM TIMEOUT: reading line from modem
> feb 05 17:14:19.97: [ 1935]: MODEM <Timeout>
> feb 05 17:14:19.97: [ 1935]: MODEM set DTR OFF
> feb 05 17:14:19.97: [ 1935]: MODEM set baud rate: 0 baud (flow control
> unchanged)
> feb 05 17:14:19.97: [ 1935]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
> 5)
> feb 05 17:14:19.97: [ 1935]: SESSION END
>