HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] Problem when sending faxes, not when receiving



Hello I have a problem when i send faxes with hylafax, when i send it in console with sendfax -vv -d xxxxxxxxx /etc/passwd everithing its ok. I have a PBX but doesnt work if it put in a single line. HereĀ“s my logs:


Jan 20 17:36:52.08: [ 6025]: SESSION BEGIN 000000666 34988988530506
Jan 20 17:36:52.10: [ 6025]: HylaFAX (tm) Version 4.3.1
Jan 20 17:36:52.10: [ 6025]: SEND FAX: JOB 166 DEST 988530506 COMMID 000000666 DEVICE '/dev/ttyS0' FROM '<xxxxx@xxxxxxxxx>' USER xxxx
Jan 20 17:36:52.10: [ 6025]: <-- [12:AT+FCLASS=1\r]
Jan 20 17:36:52.21: [ 6025]: --> [2:OK]
Jan 20 17:36:52.26: [ 6025]: DIAL xxxxxxxxx
Jan 20 17:36:52.26: [ 6025]: <-- [14:ATDTxxxxxxxxx\r]
Jan 20 17:37:09.35: [ 6025]: --> [7:CONNECT]
Jan 20 17:37:10.58: [ 6025]: --> [2:OK]
Jan 20 17:37:10.58: [ 6025]: REMOTE NSF "AD 00 36 20 00 00 00 00"
Jan 20 17:37:10.58: [ 6025]: NSF remote fax equipment: HP
Jan 20 17:37:10.58: [ 6025]: <-- [9:AT+FRH=3\r]
Jan 20 17:37:10.60: [ 6025]: --> [7:CONNECT]
Jan 20 17:37:11.29: [ 6025]: --> [2:OK]
Jan 20 17:37:11.29: [ 6025]: REMOTE CSI "xxxxxxxxx"
Jan 20 17:37:11.29: [ 6025]: <-- [9:AT+FRH=3\r]
Jan 20 17:37:11.31: [ 6025]: --> [7:CONNECT]
Jan 20 17:37:11.74: [ 6025]: --> [2:OK]
Jan 20 17:37:11.74: [ 6025]: REMOTE best rate 14400 bit/s
Jan 20 17:37:11.74: [ 6025]: REMOTE max A4 page width (215 mm)
Jan 20 17:37:11.74: [ 6025]: REMOTE max unlimited page length
Jan 20 17:37:11.74: [ 6025]: REMOTE best vres 300 x 300 dpi
Jan 20 17:37:11.74: [ 6025]: REMOTE format support: MH, MR, MMR, JPEG Full-Color
Jan 20 17:37:11.74: [ 6025]: REMOTE supports T.30 Annex A, 256-byte ECM
Jan 20 17:37:11.74: [ 6025]: REMOTE best 0 ms/scanline
Jan 20 17:37:11.74: [ 6025]: USE 14400 bit/s
Jan 20 17:37:11.74: [ 6025]: USE error correction mode
Jan 20 17:37:11.74: [ 6025]: <-- [9:AT+FTH=3\r]
Jan 20 17:37:11.79: [ 6025]: --> [7:CONNECT]
Jan 20 17:37:11.79: [ 6025]: <-- data [3]
Jan 20 17:37:11.79: [ 6025]: <-- data [2]
Jan 20 17:37:13.11: [ 6025]: --> [2:OK]
Jan 20 17:37:13.11: [ 6025]: <-- [5:ATH0\r]
Jan 20 17:37:13.54: [ 6025]: --> [10:NO CARRIER]
Jan 20 17:37:13.54: [ 6025]: MODEM No carrier
Jan 20 17:37:13.54: [ 6025]: SESSION END

My config file:

S0
# $Id: topic,v 1.4 2003/07/25 16:23:26 lhoward Exp $
#
# prototype config for Topic modems and other similarly broken firmwares
#

#
CountryCode:            34
AreaCode:               xxx
FAXNumber:              xxxxxx
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "XXXXXXXX S.L."
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#

ModemType:              Class1          # use this to supply a hint

# as of v1.20, +FTS is not supported, which will cause "Stop and wait"
# failures unless we use software pauses instead...

Class1PPMWaitCmd:       "<delay\0727>"  # \072 == :  to avoid awk problem
Class1TCFWaitCmd:       "<delay\0727>"
Class1EOPWaitCmd:       "<delay\0729>"
Class1SwitchingCmd:     "<delay\0727>"  # assumption: +FRS not supported

I dont know how to do can you help me?.


Project hosted by iFAX Solutions