Re: [hylafax-users] Faxes received with error

["Ramon F. McDougall" <rfm@xxxxxxxxxxxxxxxxxx>]

Good Evening,

I new to HylaFAX, so I can only suggest increasing the number of pages
allowed. I don't recalled the config file needed to be changed but I have
increase my to  150 pages.

Kind Regards,

Ramon

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Vágó István
Sent: Friday, December 19, 2008 5:31 AM
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Faxes received with error

Hello,

I having problem with faxes received from some fax peers. These faxes
received with the following error message. The error is only received after
the last page of these faxes. The received image otherwise looks fine. But
because the fax was not confirmed, these clients try to send them again and
again until it come over without the error (three or more times). Is there
any solution to overcome this error?

Thanks,
Istvan

Dec 17 12:52:28.86: [ 4686]: SESSION BEGIN 000009832 +362754XXXX 
Dec 17 12:52:28.86: [ 4686]: HylaFAX (tm) Version 5.2.5 
Dec 17 12:52:28.86: [ 4686]: <-- [4:ATA\r] 
Dec 17 12:52:43.58: [ 4686]: --> [4:+FCO] 
Dec 17 12:52:43.58: [ 4686]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0' 
Dec 17 12:52:43.58: [ 4686]: STATE CHANGE: ANSWERING -> RECEIVING 
Dec 17 12:52:43.58: [ 4686]: RECV FAX: begin 
Dec 17 12:52:43.85: [ 4686]: --> [27:+FTI:" 068842XXXX"] 
Dec 17 12:52:43.85: [ 4686]: REMOTE TSI "068842XXXX" 
Dec 17 12:52:43.86: [ 4686]: --> [20:+FCS:0,5,0,2,0,0,0,1] 
Dec 17 12:52:43.86: [ 4686]: REMOTE wants 14400 bit/s 
Dec 17 12:52:43.86: [ 4686]: REMOTE wants A4 page width (215 mm) 
Dec 17 12:52:43.86: [ 4686]: REMOTE wants unlimited page length 
Dec 17 12:52:43.86: [ 4686]: REMOTE wants 3.85 line/mm 
Dec 17 12:52:43.87: [ 4686]: REMOTE wants 1-D MH 
Dec 17 12:52:43.87: [ 4686]: --> [2:OK] 
Dec 17 12:52:43.87: [ 4686]: <-- [7:AT+FDR\r] 
Dec 17 12:52:49.12: [ 4686]: --> [20:+FCS:0,5,0,2,0,0,0,1] 
Dec 17 12:52:49.12: [ 4686]: REMOTE wants 14400 bit/s 
Dec 17 12:52:49.12: [ 4686]: REMOTE wants A4 page width (215 mm) 
Dec 17 12:52:49.12: [ 4686]: REMOTE wants unlimited page length 
Dec 17 12:52:49.12: [ 4686]: REMOTE wants 3.85 line/mm 
Dec 17 12:52:49.12: [ 4686]: REMOTE wants 1-D MH 
Dec 17 12:52:49.12: [ 4686]: --> [7:CONNECT] 
Dec 17 12:52:49.12: [ 4686]: RECV: begin page 
Dec 17 12:52:49.12: [ 4686]: MODEM set XON/XOFF/DRAIN: input ignored,
output generated 
Dec 17 12:52:49.12: [ 4686]: RECV: send trigger 022 
Dec 17 12:52:49.12: [ 4686]: Copy quality checking performed by modem 
Dec 17 12:52:49.14: [ 4686]: RECV/CQ: Invalid BlackTable code word, row 0,
x 143 
Dec 17 12:52:49.14: [ 4686]: RECV/CQ: Bad 1D pixel count, row 0, got 143,
expected 1728 
Dec 17 12:53:04.06: [ 4686]: RECV/CQ: Bad 1D pixel count, row 1126, got 0,
expected 1728 
Dec 17 12:53:04.06: [ 4686]: RECV/CQ: Bad 1D pixel count, row 1127, got 0,
expected 1728 
Dec 17 12:53:04.06: [ 4686]: RECV/CQ: Bad 1D pixel count, row 1128, got 0,
expected 1728 
Dec 17 12:53:04.07: [ 4686]: RECV/CQ: Bad 1D pixel count, row 1129, got 0,
expected 1728 
Dec 17 12:53:04.07: [ 4686]: RECV: 26942 bytes of data, 1130 total lines 
Dec 17 12:53:04.07: [ 4686]: RECV/CQ: Adjusting for RTC found at row 1126 
Dec 17 12:53:04.07: [ 4686]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled 
Dec 17 12:53:05.37: [ 4686]: --> [20:+FPS:2,2880,9240,2,0] 
Dec 17 12:53:05.38: [ 4686]: --> [6:+FET:2] 
Dec 17 12:53:05.38: [ 4686]: RECV recv EOP (no more pages or documents) 
Dec 17 12:53:05.38: [ 4686]: --> [2:OK] 
Dec 17 12:53:05.38: [ 4686]: RECV send RTN (retrain negative) 
Dec 17 12:53:05.38: [ 4686]: <-- [7:AT+FDR\r] 
Dec 17 12:53:08.03: [ 4686]: --> [5:ERROR] 
Dec 17 12:53:08.03: [ 4686]: REMOTE HANGUP: Unspecified Phase C error,
including too much delay between TCF and +FDR command (code 90) 
Dec 17 12:53:08.03: [ 4686]: RECV keeping unconfirmed page 
Dec 17 12:53:08.03: [ 4686]: RECV FAX (000009832): from 068842XXXX, page 1
in 0:00:21, INF, 3.85 line/mm, 1-D MH, 14400 bit/s 
Dec 17 12:53:09.03: [ 4686]: RECV FAX (000009832): recvq/fax000015752.tif
from 068842XXXX, subaddress <unspecified>, 1 pages in 0:00:25 
Dec 17 12:53:09.03: [ 4686]: RECV FAX: Unspecified Phase C error, including
too much delay between TCF and +FDR command {E250} 
Dec 17 12:53:09.03: [ 4686]: <-- [7:AT+FKS\r] 
Dec 17 12:53:09.05: [ 4686]: --> [5:ERROR] 
Dec 17 12:53:09.05: [ 4686]: MODEM Command error 
Dec 17 12:53:09.05: [ 4686]: RECV FAX (000009832): session with 068842XXXX
terminated abnormally: Unspecified Phase C error, including too much delay
between TCF and +FDR command {E250} 
Dec 17 12:53:09.05: [ 4686]: RECV FAX: bin/faxrcvd 'recvq/fax000015752.tif'
'ttyS0' '000009832' 'Unspecified Phase C error, including too much delay
between TCF and +FDR command {E250}' 
Dec 17 12:53:09.05: [ 4686]: RECV FAX: end 
Dec 17 12:53:09.05: [ 4686]: SESSION END 


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*