Re: [hylafax-users] waiting for v.21 carrier + Failure to train modems

[Lee Howard <faxguy@xxxxxxxxxxxxxxxx>]

hbfornies@xxxxxxxxxxx wrote:
> Oct 28 09:06:23.14: [ 5791]: <-- [9:AT+FRH=3\r]
> Oct 28 09:06:23.64: [ 5791]: --> [7:CONNECT]
> Oct 28 09:06:25.28: [ 5791]: --> HDLC<25:FF C0 C2 AC 6C 9C 1C 4C AC 6C 
> EC 9C 04 04 04 04 04 04 04 04 04 04 04 A5 0D>
> Oct 28 09:06:25.28: [ 5791]: --> [2:OK]
> Oct 28 09:06:25.28: [ 5791]: REMOTE TSI "xxxxxxxxx"
> Oct 28 09:06:25.28: [ 5791]: RECV recv TSI (sender id)
> Oct 28 09:06:25.28: [ 5791]: <-- [9:AT+FRH=3\r]
> Oct 28 09:06:25.72: [ 5791]: --> [7:CONNECT]
> Oct 28 09:06:25.72: [ 5791]: --> HDLC<15:FF C8 C1 00 60 1F 23 01 01 01 
> 01 01 00 8C 11>
> Oct 28 09:06:25.76: [ 5791]: --> [2:OK]
> Oct 28 09:06:25.76: [ 5791]: REMOTE wants 9600 bit/s
> Oct 28 09:06:25.76: [ 5791]: REMOTE wants A4 page width (215 mm)
> Oct 28 09:06:25.76: [ 5791]: REMOTE wants unlimited page length
> Oct 28 09:06:25.76: [ 5791]: REMOTE wants 3.85 line/mm
> Oct 28 09:06:25.76: [ 5791]: REMOTE wants 2-D MMR
> Oct 28 09:06:25.76: [ 5791]: REMOTE wants T.30 Annex A, 256-byte ECM
> Oct 28 09:06:25.76: [ 5791]: RECV recv DCS (command signal)
> Oct 28 09:06:25.76: [ 5791]: RECV training at v.29 9600 bit/s
> Oct 28 09:06:25.76: [ 5791]: MODEM set XON/XOFF/DRAIN: input ignored, 
> output generated
> Oct 28 09:06:25.76: [ 5791]: <-- [10:AT+FRM=96\r]
> Oct 28 09:06:30.26: [ 5791]: --> [0:]
> Oct 28 09:06:30.26: [ 5791]: MODEM <Empty line>
> Oct 28 09:06:30.26: [ 5791]: MODEM TIMEOUT: receiving TCF
> Oct 28 09:06:30.26: [ 5791]: <-- data [1]
> Oct 28 09:06:30.28: [ 5791]: --> [2:OK]
> Oct 28 09:06:30.28: [ 5791]: MODEM set XON/XOFF/DRAIN: input ignored, 
> output disabled
> Oct 28 09:06:30.28: [ 5791]: <-- [9:AT+FRS=7\r]
> Oct 28 09:06:30.30: [ 5791]: --> [2:OK]
> Oct 28 09:06:30.30: [ 5791]: <-- [9:AT+FTH=3\r]
> Oct 28 09:06:30.32: [ 5791]: --> [7:CONNECT]
> Oct 28 09:06:30.32: [ 5791]: <-- HDLC<3:FF C8 22>
> Oct 28 09:06:30.32: [ 5791]: <-- data [3]
> Oct 28 09:06:30.32: [ 5791]: <-- data [2]
> Oct 28 09:06:31.40: [ 5791]: --> [2:OK]
> Oct 28 09:06:31.40: [ 5791]: TRAINING failed
> Oct 28 09:06:31.40: [ 5791]: <-- [9:AT+FRH=3\r]
> Oct 28 09:06:38.40: [ 5791]: --> [0:]
> Oct 28 09:06:38.40: [ 5791]: MODEM <Empty line>
> Oct 28 09:06:38.40: [ 5791]: MODEM TIMEOUT: waiting for v.21 carrier
> Oct 28 09:06:38.40: [ 5791]: <-- data [1]
> Oct 28 09:06:38.42: [ 5791]: --> [2:]
> Oct 28 09:06:38.42: [ 5791]: --> [2:OK]

What kind of zaptel hardware are you using?  The log seems to indicate 
that the audio is very corrupt.

Thanks,

Lee.


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*