[hylafax-users] US Robitcs External Modem Send Problems

["Bowman, Mark" <mabowman@xxxxxxxxxxxxxxxxxxxxxx>]

I have a US Robotics Faxmodem V.90 56k Standard and x2 technology compatible. . I can receive faxes on this modem just fine. When I go to send a fax, I can hear the modem initialize, and connect up to the remote machine. It then just disconnects and never sends the faxes. I have attached the modem config.cuad0 file, and one of the send file logs.

 

Any help would be appreciated.

 

Modem Config File

# $Id: class2.0,v 1.12 1996/06/24 02:58:33 sam Rel $

#

# HylaFAX Facsimile Software

#

# Copyright (c) 1990-1996 Sam Leffler

# Copyright (c) 1991-1996 Silicon Graphics, Inc.

# HylaFAX is a trademark of Silicon Graphics, Inc.

#

# Permission to use, copy, modify, distribute, and sell this software and

# its documentation for any purpose is hereby granted without fee, provided

# that (i) the above copyright notices and this permission notice appear in

# all copies of the software and related documentation, and (ii) the names of

# Sam Leffler and Silicon Graphics may not be used in any advertising or

# publicity relating to the software without the specific, prior written

# permission of Sam Leffler and Silicon Graphics.

#

# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,

# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY

# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 

#

# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR

# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,

# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,

# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF

# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE

# OF THIS SOFTWARE.

#

#

# Generic Class 2.0 modem configuration.

#

# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP

#

CountryCode:            1

AreaCode:               989

FAXNumber:              +1.###.###.####

LongDistancePrefix:     1

InternationalPrefix:    011

DialStringRules:        etc/dialrules

ServerTracing:          1

SessionTracing:         11

RecvFileMode:           0644

LogFileMode:            0600

DeviceMode:             0600

RingsBeforeAnswer:      1

SpeakerVolume:          on

GettyArgs:              "-h %l dx_%s"

LocalIdentifier:        "Name"

TagLineFont:            etc/lutRS18.pcf

TagLineFormat:          "From %%l|%c|Page %%p of %%t"

QualifyTSI:            

MaxRecvPages:           25

#

#

# Modem-related stuff: should reflect modem command interface

# and hardware connection/cabling (e.g. flow control).

#

ModemType:              Class1        # use this to supply a hint

ModemRate:              14400

ModemFlowControl:       rtscts

# ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem

ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)

#

# We normally append the "@" symbol to the dial string so that

# the modem will wait 5 seconds before attempting to connect

# and return result codes that distinguish between no carrier

# and no answer.  This makes it possible to avoid problems with

# repeatedly dialing a number that doesn't have a fax machine

# (kudos to Stuart Lynne for this trick.)

#

# NB: If you need to prefix phone numbers to get through a PBX,

#     put it in the ModemDialCmd; e.g. "DT9%s@".

#

ModemDialCmd:           ATDT%s          # T for tone dialing, @ for silence

#

# Other possible configuration stuff.  The default strings are

# shown below.  Only those that are different from the defaults

# need to be included in the configuration file.

#

ModemResetCmds:         ""              # stuff to do when modem is reset

ModemAnswerCmd:         ATA             # use this to answer phone

# ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer

# ModemNoFlowCmd:         AT&H0&I0&R1

ModemHardFlowCmd:       AT&H1&I0&R2

# ModemSoftFlowCmd:       AT&H2&I2&R1

#

# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.

# Note that we both turn the speaker on/off and set volume.

#

ModemSetVolumeCmd:      "ATL2M1"

ModemEchoOffCmd:        ATE0            # disable command echo

ModemVerboseResultsCmd: ATV1            # enable verbose command results

ModemResultCodesCmd:    ATQ0X4

# ModemOnHookCmd:         ATH0            # place phone on hook (hangup)

ModemSoftResetCmd:      ATZ             # do soft reset of modem

# ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier

# ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds

ModemRecvFillOrder:     LSB2MSB         # bit order of received facsimile

ModemSendFillOrder:     LSB2MSB         # bit order modem expects for transmit

#

# Configuration parameters for Class 2.0 modems.

#

Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0

Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)

Class2CQCmd:            ""              # commands to enable copy quality proc.

Class2AbortCmd:         AT+FKS          # abort session command

Class2CQQueryCmd:       !(0),(0)        # query for copy quality capabilities

Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities

Class2TBCCmd:           AT+FPP=0        # setup stream mode

Class2CRCmd:            AT+FCR=1        # enable capability to receive

Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter

Class2BUGCmd:           AT+FBU=0        # enable HDLC frame tracing

Class2LIDCmd:           AT+FLI          # set local identifier command

Class2DCCCmd:           AT+FCC          # set modem capabilities command

Class2DISCmd:           AT+FIS          # set session parameters command

Class2DDISCmd:          ""              # disable pre-dial DIS command hack

Class2CIGCmd:           AT+FPI          # set polling identifier command

Class2NRCmd:            AT+FNR=1,1,1,0  # setup status reporting command

Class2PIECmd:          

Class2PTSCmd:           AT+FPS          # set post-page status command

Class2SPLCmd:           AT+FSP          # set polling indicator command

# Class2NFLOCmd:          AT+FLO=0        # set no flow control command

# Class2SFLOCmd:          AT+FLO=1        # set software flow control command

Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command

 

Recevie Log File

 

Oct 23 09:06:44.36: [ 1296]: SESSION BEGIN 000000106 19899894532015

Oct 23 09:06:44.36: [ 1296]: HylaFAX (tm) Version 4.3.4

Oct 23 09:06:44.36: [ 1296]: SEND FAX: JOB 57 DEST 9894532015 COMMID 000000106 DEVICE '/dev/cuad0' FROM 'Mark Bowman <mabowman@xxxxxxxxxxx>' USER root

Oct 23 09:06:44.37: [ 1296]: <-- [12:AT+FCLASS=1\r]

Oct 23 09:06:44.51: [ 1296]: --> [2:OK]

Oct 23 09:06:44.51: [ 1296]: DIAL 9894532015

Oct 23 09:06:44.51: [ 1296]: <-- [15:ATDT9894532015\r]

Oct 23 09:06:53.73: [ 1296]: --> [7:CONNECT]

Oct 23 09:06:55.01: [ 1296]: --> [2:OK]

Oct 23 09:06:55.01: [ 1296]: REMOTE NSF "00 00 56 55 55 00 8C 90 80 96 05"

Oct 23 09:06:55.01: [ 1296]: NSF remote fax equipment: Brother MFC-3100C/MFC-8600

Oct 23 09:06:55.01: [ 1296]: <-- [9:AT+FRH=3\r]

Oct 23 09:06:55.02: [ 1296]: --> [7:CONNECT]

Oct 23 09:06:55.43: [ 1296]: --> [2:OK]

Oct 23 09:06:55.43: [ 1296]: REMOTE best rate 14400 bit/s

Oct 23 09:06:55.43: [ 1296]: REMOTE max A4 page width (215 mm)

Oct 23 09:06:55.43: [ 1296]: REMOTE max unlimited page length

Oct 23 09:06:55.43: [ 1296]: REMOTE best vres 15.4 line/mm

Oct 23 09:06:55.43: [ 1296]: REMOTE format support: MH, MR, MMR, JPEG Full-Color

Oct 23 09:06:55.43: [ 1296]: REMOTE supports T.30 Annex A, 256-byte ECM

Oct 23 09:06:55.43: [ 1296]: REMOTE best 20 ms, 10 ms/scanline

Oct 23 09:06:55.43: [ 1296]: USE 14400 bit/s

Oct 23 09:06:55.43: [ 1296]: USE error correction mode

Oct 23 09:06:55.43: [ 1296]: <-- [9:AT+FTH=3\r]

Oct 23 09:06:55.63: [ 1296]: --> [7:CONNECT]

Oct 23 09:06:55.63: [ 1296]: <-- data [3]

Oct 23 09:06:55.63: [ 1296]: <-- data [2]

Oct 23 09:06:56.80: [ 1296]: --> [2:OK]

Oct 23 09:06:56.80: [ 1296]: <-- [5:ATH0\r]

Oct 23 09:06:57.04: [ 1296]: --> [2:OK]

Oct 23 09:06:57.04: [ 1296]: SESSION END

 

Mark Bowman

I.T. Manager

Gannett Directories

989-453-2030 Ext. 126

248-416-2961 (Cell)