[hylafax-users] ERROR COMREC

[RAMSUS23 <federico23@xxxxxxxxx>]

Hello I have an error when I receive a fax: COMREC receive invalid command ... how can I fix it?

the modem is configured so ttyS1:



#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and XON/XOFF flow control.
#
#
CountryCode:            8
AreaCode:               0039
FAXNumber:              0112274406
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0666
LogFileMode:            0666
DeviceMode:             0666
RingsBeforeAnswer:      3
SpeakerVolume:          low
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Anest Europe"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
MaxConsecutiveBadLine:  0
PercentGoodLines:       0
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              9600            # rate for DCE-DTE communication
ModemFlowControl:       xonxoff         # software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX returns a multi-line result
#
ModemDialCmd:           ATX3DT%s
ModemReadyState:        D
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow control
Class1SFLOCmd:          ""              # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for response
Class1TCFMaxNonZero:    70
Class1TCFMinRun:        1000
Class1RecvAbortOK:      200
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
#
# When using AT+FRS=n we see USR modems reset themselves in the middle of sessions
# this is not good.  So, we seem to work-around that problem by not using the
# command.  Unfortunately, this isn't an ideal thing.
#
Class1SwitchingCmd:     "<delay\0727>"