Re: [hylafax-users] Problem to send faxes

[snORky <snorky@xxxxxxxxxxxxx>]

> Alle 19:13, venerdì 20 giugno 2008, snORky ha scritto:
> Hi All
>
> I have a problem with hylafax-4.4.4 on Slackware GNU/Linux 11.0 kernel
> 2.6.21.3
>
> I cannot send certain fax.
>
> I attach the log:
> ----------------------------------------------------
>
> Your job to ********** failed because:
>
> No response to EOP repeated 3 tries; Giving up after 3 attempts to send
> same page
>
>
>     ---- Transcript of session follows ----
>
> Jun 19 19:01:43.61: [ 3933]: SESSION BEGIN 000004828 1**************
> Jun 19 19:01:43.61: [ 3933]: HylaFAX (tm) Version 4.4.4
> Jun 19 19:01:43.61: [ 3933]: SEND FAX: JOB 1349 DEST ********** COMMID
> 000004828 DEVICE '/dev/ttyS0' FROM '***** <*****@*********.lan>' USER *****
> Jun 19 19:01:43.61: [ 3933]: <-- [12:AT+FCLASS=1\r]
> Jun 19 19:01:43.72: [ 3933]: --> [2:OK]
> Jun 19 19:01:43.72: [ 3933]: DIAL *********
> Jun 19 19:01:43.72: [ 3933]: <-- [15:ATDT**********\r]
> Jun 19 19:02:27.33: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:28.78: [ 3933]: --> [2:OK]
> Jun 19 19:02:28.78: [ 3933]: REMOTE NSF "50 80 00 26 00 00 02 00 00 00 00
> 00 00 00 00 00 00 00 00 FF"
> Jun 19 19:02:28.78: [ 3933]: NSF remote fax equipment: unknown
> Jun 19 19:02:28.78: [ 3933]: <-- [9:AT+FRH=3\r]
> Jun 19 19:02:28.80: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:29.48: [ 3933]: --> [2:OK]
> Jun 19 19:02:29.48: [ 3933]: REMOTE CSI ""
> Jun 19 19:02:29.48: [ 3933]: <-- [9:AT+FRH=3\r]
> Jun 19 19:02:29.50: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:29.84: [ 3933]: --> [2:OK]
> Jun 19 19:02:29.84: [ 3933]: REMOTE best rate 9600 bit/s
> Jun 19 19:02:29.84: [ 3933]: REMOTE max A4 page width (215 mm)
> Jun 19 19:02:29.84: [ 3933]: REMOTE max unlimited page length
> Jun 19 19:02:29.84: [ 3933]: REMOTE best vres 7.7 line/mm
> Jun 19 19:02:29.84: [ 3933]: REMOTE format support: MH, MR
> Jun 19 19:02:29.84: [ 3933]: REMOTE best 20 ms, 10 ms/scanline
> Jun 19 19:02:29.84: [ 3933]: USE 9600 bit/s
> Jun 19 19:02:29.84: [ 3933]: SEND file "docq/doc1357.ps;41"
> Jun 19 19:02:29.84: [ 3933]: USE A4 page width (215 mm)
> Jun 19 19:02:29.84: [ 3933]: USE unlimited page length
> Jun 19 19:02:29.84: [ 3933]: USE 7.7 line/mm
> Jun 19 19:02:29.84: [ 3933]: USE 2-D MR
> Jun 19 19:02:29.84: [ 3933]: USE 10 ms/scanline
> Jun 19 19:02:29.84: [ 3933]: SEND training at v.29 9600 bit/s
> Jun 19 19:02:29.84: [ 3933]: DELAY 70 ms
> Jun 19 19:02:29.91: [ 3933]: <-- [9:AT+FTH=3\r]
> Jun 19 19:02:29.96: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:29.96: [ 3933]: <-- data [23]
> Jun 19 19:02:29.96: [ 3933]: <-- data [2]
> Jun 19 19:02:29.98: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:29.98: [ 3933]: <-- data [6]
> Jun 19 19:02:29.98: [ 3933]: <-- data [2]
> Jun 19 19:02:32.15: [ 3933]: --> [2:OK]
> Jun 19 19:02:32.15: [ 3933]: DELAY 70 ms
> Jun 19 19:02:32.22: [ 3933]: <-- [10:AT+FTM=96\r]
> Jun 19 19:02:32.74: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:32.74: [ 3933]: <-- data [1024]
> Jun 19 19:02:32.74: [ 3933]: <-- data [776]
> Jun 19 19:02:32.74: [ 3933]: <-- data [2]
> Jun 19 19:02:34.29: [ 3933]: --> [2:OK]
> Jun 19 19:02:34.29: [ 3933]: <-- [9:AT+FRH=3\r]
> Jun 19 19:02:34.79: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:35.96: [ 3933]: --> [2:OK]
> Jun 19 19:02:35.96: [ 3933]: TRAINING succeeded
> Jun 19 19:02:35.96: [ 3933]: DELAY 70 ms
> Jun 19 19:02:36.03: [ 3933]: <-- [10:AT+FTM=96\r]
> Jun 19 19:02:36.62: [ 3933]: --> [7:CONNECT]
> Jun 19 19:02:36.62: [ 3933]: SEND begin page
> Jun 19 19:02:36.62: [ 3933]: <-- data [1025]
> Jun 19 19:02:36.62: [ 3933]: <-- data [1027]
> Jun 19 19:02:36.62: [ 3933]: <-- data [1032]
> Jun 19 19:02:36.62: [ 3933]: <-- data [1033]
> Jun 19 19:02:38.61: [ 3933]: <-- data [1038]
> Jun 19 19:02:38.61: [ 3933]: <-- data [1031]
> Jun 19 19:02:38.61: [ 3933]: <-- data [1036]
> Jun 19 19:02:38.61: [ 3933]: <-- data [1032]
> Jun 19 19:02:40.61: [ 3933]: <-- data [1033]
> Jun 19 19:02:40.61: [ 3933]: <-- data [1030]
> Jun 19 19:02:40.61: [ 3933]: <-- data [1035]
> Jun 19 19:02:40.61: [ 3933]: <-- data [1029]
> Jun 19 19:02:42.60: [ 3933]: <-- data [1033]
> Jun 19 19:02:42.60: [ 3933]: <-- data [1038]
> Jun 19 19:02:42.61: [ 3933]: <-- data [1026]
> Jun 19 19:02:42.61: [ 3933]: <-- data [1029]
> Jun 19 19:02:44.60: [ 3933]: <-- data [1027]
> Jun 19 19:02:44.60: [ 3933]: <-- data [1033]
> Jun 19 19:02:44.60: [ 3933]: <-- data [1025]
> Jun 19 19:02:46.60: [ 3933]: <-- data [1025]
> Jun 19 19:02:46.60: [ 3933]: <-- data [1029]
> Jun 19 19:02:46.60: [ 3933]: <-- data [1038]
> Jun 19 19:02:46.60: [ 3933]: <-- data [1030]
> Jun 19 19:02:48.59: [ 3933]: <-- data [1029]
> Jun 19 19:02:48.59: [ 3933]: <-- data [1025]
> Jun 19 19:02:48.59: [ 3933]: <-- data [1030]
> Jun 19 19:02:48.59: [ 3933]: <-- data [871]
> Jun 19 19:02:50.59: [ 3933]: SENT 27490 bytes of data
> Jun 19 19:02:50.59: [ 3933]: <-- data [1027]
> Jun 19 19:02:50.59: [ 3933]: <-- data [1025]
> Jun 19 19:02:50.59: [ 3933]: <-- data [1033]
> Jun 19 19:02:50.59: [ 3933]: <-- data [1029]
> Jun 19 19:02:52.59: [ 3933]: <-- data [1027]
> Jun 19 19:02:52.59: [ 3933]: <-- data [1029]
> Jun 19 19:02:52.59: [ 3933]: <-- data [1027]
> Jun 19 19:02:54.58: [ 3933]: <-- data [1027]
> Jun 19 19:02:54.58: [ 3933]: <-- data [1033]
> Jun 19 19:02:54.58: [ 3933]: <-- data [1028]
> Jun 19 19:02:54.58: [ 3933]: <-- data [1030]
> Jun 19 19:02:56.57: [ 3933]: <-- data [1025]
> Jun 19 19:02:56.57: [ 3933]: <-- data [1029]
> Jun 19 19:02:56.57: [ 3933]: <-- data [1024]
> Jun 19 19:02:56.57: [ 3933]: <-- data [1024]
> Jun 19 19:02:58.57: [ 3933]: <-- data [1024]
> Jun 19 19:02:58.57: [ 3933]: <-- data [1024]
> Jun 19 19:02:58.57: [ 3933]: <-- data [1024]
> Jun 19 19:02:58.57: [ 3933]: <-- data [1024]
> Jun 19 19:03:00.56: [ 3933]: <-- data [1024]
> Jun 19 19:03:00.56: [ 3933]: <-- data [1031]
> Jun 19 19:03:00.56: [ 3933]: <-- data [1029]
> Jun 19 19:03:02.56: [ 3933]: <-- data [1037]
> Jun 19 19:03:02.56: [ 3933]: <-- data [1031]
> Jun 19 19:03:02.56: [ 3933]: <-- data [1036]
> Jun 19 19:03:02.56: [ 3933]: <-- data [1024]
> Jun 19 19:03:04.55: [ 3933]: <-- data [875]
> Jun 19 19:03:04.55: [ 3933]: SENT 27497 bytes of data
> Jun 19 19:03:04.55: [ 3933]: <-- data [1032]
> Jun 19 19:03:04.55: [ 3933]: <-- data [1024]
> Jun 19 19:03:04.56: [ 3933]: <-- data [1027]
> Jun 19 19:03:06.55: [ 3933]: <-- data [161]
> Jun 19 19:03:06.55: [ 3933]: SENT 3233 bytes of data
> Jun 19 19:03:06.55: [ 3933]: SEND 2D RTC
> Jun 19 19:03:06.55: [ 3933]: <-- data [30]
> Jun 19 19:03:06.55: [ 3933]: <-- data [2]
> Jun 19 19:03:06.55: [ 3933]: SEND end page
> Jun 19 19:03:25.42: [ 3933]: --> [2:OK]
> Jun 19 19:03:25.42: [ 3933]: DELAY 90 ms
> Jun 19 19:03:25.51: [ 3933]: SEND send EOP (no more pages or documents)
> Jun 19 19:03:25.51: [ 3933]: <-- [9:AT+FTH=3\r]
> Jun 19 19:03:25.56: [ 3933]: --> [7:CONNECT]
> Jun 19 19:03:25.56: [ 3933]: <-- data [3]
> Jun 19 19:03:25.56: [ 3933]: <-- data [2]
> Jun 19 19:03:26.89: [ 3933]: --> [2:OK]
> Jun 19 19:03:26.89: [ 3933]: <-- [9:AT+FRH=3\r]
> Jun 19 19:03:30.00: [ 3933]: --> [0:]
> Jun 19 19:03:30.00: [ 3933]: MODEM <Empty line>
> Jun 19 19:03:30.00: [ 3933]: <-- data [1]
> Jun 19 19:03:30.20: [ 3933]: MODEM <Timeout>
> Jun 19 19:03:30.20: [ 3933]: SEND send EOP (no more pages or documents)
> Jun 19 19:03:30.20: [ 3933]: <-- [9:AT+FTH=3\r]
> Jun 19 19:03:30.25: [ 3933]: --> [7:CONNECT]
> Jun 19 19:03:30.25: [ 3933]: <-- data [3]
> Jun 19 19:03:30.25: [ 3933]: <-- data [2]
> Jun 19 19:03:31.57: [ 3933]: --> [2:OK]
> Jun 19 19:03:31.57: [ 3933]: <-- [9:AT+FRH=3\r]
> Jun 19 19:03:34.67: [ 3933]: --> [0:]
> Jun 19 19:03:34.67: [ 3933]: MODEM <Empty line>
> Jun 19 19:03:34.67: [ 3933]: <-- data [1]
> Jun 19 19:03:34.87: [ 3933]: MODEM <Timeout>
> Jun 19 19:03:34.87: [ 3933]: SEND send EOP (no more pages or documents)
> Jun 19 19:03:34.87: [ 3933]: <-- [9:AT+FTH=3\r]
> Jun 19 19:03:34.92: [ 3933]: --> [7:CONNECT]
> Jun 19 19:03:34.92: [ 3933]: <-- data [3]
> Jun 19 19:03:34.92: [ 3933]: <-- data [2]
> Jun 19 19:03:36.24: [ 3933]: --> [2:OK]
> Jun 19 19:03:36.24: [ 3933]: <-- [9:AT+FRH=3\r]
> Jun 19 19:03:39.34: [ 3933]: --> [0:]
> Jun 19 19:03:39.34: [ 3933]: MODEM <Empty line>
> Jun 19 19:03:39.34: [ 3933]: <-- data [1]
> Jun 19 19:03:39.54: [ 3933]: MODEM <Timeout>
> Jun 19 19:03:39.54: [ 3933]: No response to EOP repeated 3 tries
> Jun 19 19:03:39.54: [ 3933]: SEND: Giving up after 3 attempts to send same
> page "docq/doc1357.ps;41", dirnum 0
> Jun 19 19:03:39.54: [ 3933]: DELAY 70 ms
> Jun 19 19:03:39.62: [ 3933]: <-- [9:AT+FTH=3\r]
> Jun 19 19:03:39.66: [ 3933]: --> [7:CONNECT]
> Jun 19 19:03:39.66: [ 3933]: <-- data [3]
> Jun 19 19:03:39.66: [ 3933]: <-- data [2]
> Jun 19 19:03:40.98: [ 3933]: --> [2:OK]
> Jun 19 19:03:41.98: [ 3933]: <-- [5:ATH0\r]
> Jun 19 19:03:42.08: [ 3933]: --> [10:NO CARRIER]
> Jun 19 19:03:42.08: [ 3933]: MODEM No carrier
> Jun 19 19:03:42.08: [ 3933]: SESSION END
>
>
> ------- Unsent job status -------
>       Destination: **********
>             JobID: 1349
>           GroupID: 1349
>            Sender: *****
>          Mailaddr: *****@*****.lan
>            CommID: 000004828
>             Modem: any
>    Submitted From: *************
>        Page Width: 209  (mm)
>       Page Length: 296 (mm)
>        Resolution: 196 (lpi)
>            Status: No response to EOP repeated 3 tries; Giving up after 3
> attempts to send same page
>           Dialogs: 3
>             Dials: 0
>             Calls: 3
>             Pages: 0
>          TotPages: 1
>          Attempts: 3
>            Dirnum:
>
> ----------------------------------------------------
>
>
> This is the config.ttyS0 file
> ----------------------------------------------------
>
> # $Id: topic,v 1.4 2003/07/25 16:23:26 lhoward Exp $
> #
> # prototype config for Topic modems and other similarly broken firmwares
> #
>
> #
> CountryCode:            1
> AreaCode:               ****
> FAXNumber:              +*************
> LongDistancePrefix:     1
> InternationalPrefix:    011
> DialStringRules:        etc/dialrules
> ServerTracing:          1
> SessionTracing:         11
> RecvFileMode:           0600
> LogFileMode:            0600
> DeviceMode:             0600
> RingsBeforeAnswer:      2
> SpeakerVolume:          medium
> GettyArgs:              "-h %l dx_%s"
> LocalIdentifier:        "******************"
> TagLineFont:            etc/lutRS18.pcf
> TagLineFormat:          "From %%l|%c|Page %%P of %%T"
> MaxRecvPages:           25
> #
>
> ModemType:              Class1          # use this to supply a hint
>
> # as of v1.20, +FTS is not supported, which will cause "Stop and wait"
> # failures unless we use software pauses instead...
>
> Class1PPMWaitCmd:       "<delay\0727>"  # \072 == :  to avoid awk problem
> Class1TCFWaitCmd:       "<delay\0727>"
> Class1EOPWaitCmd:       "<delay\0729>"
> Class1SwitchingCmd:     "<delay\0727>"  # assumption: +FRS not supported
>
> ----------------------------------------------------

I added this line to config.ttyS0

RTNHandlingMethod:      giveup
or
RTNHandlingMethod:      ignore

but i don't send any facsimile

help me, please...

-- 
snORky
Para todos todo,
Nada para nosotros.


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*