[hylafax-users] agere mars lt modem configuration

[Riccardo Magliocchetti <riccardo.magliocchetti@xxxxxxxxx>]

Hi,

i've just bought two agere linmodems from ebay, don't ask why it wasn't 
on purpose. I've installed the martian drivers and i've configured them 
with the default configuration of a class 1 modem. The only test i can 
do actually is to try to send to a busy fax line and seems to work, see 
log below. Is that ok or some tweaking is needed? Then is possible to 
add a default template for these "LT V.92 Data+Fax Modem Version 8.30"?

FaxSend[5666]: MODEM set DTR OFF
FaxSend[5666]: MODEM set baud rate: 0 baud (flow control unchanged)
FaxSend[5666]: DELAY 75 ms
FaxSend[5666]: MODEM set DTR ON
FaxSend[5666]: DELAY 2600 ms
FaxSend[5666]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, 
output flow XON/XOFF
FaxSend[5666]: DELAY 10 ms
FaxSend[5666]: MODEM flush i/o
FaxSend[5666]: <-- [4:ATZ\r]
martian: info: session: Started Fri Jun 20 11:42:28 2008
FaxSend[5666]: --> [3:ATZ]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: DELAY 3000 ms
FaxSend[5666]: MODEM flush i/o
FaxSend[5666]: <-- [7:ATS0=0\r]
FaxSend[5666]: --> [6:ATS0=0]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: <-- [5:ATE0\r]
FaxSend[5666]: --> [4:ATE0]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: <-- [5:ATV1\r]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: <-- [5:ATQ0\r]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: <-- [7:ATS8=2\r]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: <-- [8:ATS7=60\r]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: <-- [12:AT+FCLASS=?\r]
FaxSend[5666]: --> [3:0,1]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: MODEM Supports "Data"
FaxSend[5666]: MODEM Supports "Class 1"
FaxSend[5666]: <-- [12:AT+FCLASS=1\r]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: <-- [5:ATI3\r]
FaxSend[5666]: --> [35:LT V.92 Data+Fax Modem Version 8.30]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: MODEM: Mfr LT V.92 Data+Fax Modem Version 8.30
FaxSend[5666]: <-- [5:ATI0\r]
FaxSend[5666]: --> [35:LT V.92 Data+Fax Modem Version 8.30]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: MODEM: Model LT V.92 Data+Fax Modem Version 8.30
FaxSend[5666]: <-- [9:AT+FTM=?\r]
FaxSend[5666]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: MODEM Supports 3.85 line/mm
FaxSend[5666]: MODEM Supports 7.7 line/mm
FaxSend[5666]: MODEM Supports 15.4 line/mm
FaxSend[5666]: MODEM Supports R16 x 15.4 line/mm
FaxSend[5666]: MODEM Supports 200 x 100 dpi
FaxSend[5666]: MODEM Supports 200 x 200 dpi
FaxSend[5666]: MODEM Supports 200 x 400 dpi
FaxSend[5666]: MODEM Supports 300 x 300 dpi
FaxSend[5666]: MODEM Supports 2400 bit/s
FaxSend[5666]: MODEM Supports 4800 bit/s
FaxSend[5666]: MODEM Supports 7200 bit/s
FaxSend[5666]: MODEM Supports 9600 bit/s
FaxSend[5666]: MODEM Supports 12000 bit/s
FaxSend[5666]: MODEM Supports 14400 bit/s
FaxSend[5666]: MODEM Supports A4 page width (215 mm)
FaxSend[5666]: MODEM Supports B4 page width (255 mm)
FaxSend[5666]: MODEM Supports A3 page width (303 mm)
FaxSend[5666]: MODEM Supports A4 page length (297 mm)
FaxSend[5666]: MODEM Supports B4 page length (364 mm)
FaxSend[5666]: MODEM Supports unlimited page length
FaxSend[5666]: MODEM Supports 1-D MH
FaxSend[5666]: MODEM Supports 2-D MR
FaxSend[5666]: MODEM Supports 2-D MMR
FaxSend[5666]: MODEM Supports no ECM
FaxSend[5666]: MODEM Supports T.30 Annex A, 64-byte ECM
FaxSend[5666]: MODEM Supports T.30 Annex A, 256-byte ECM
FaxSend[5666]: MODEM Supports 0 ms/scanline
FaxSend[5666]: MODEM Supports 5 ms/scanline
FaxSend[5666]: MODEM Supports 10 ms, 5 ms/scanline
FaxSend[5666]: MODEM Supports 10 ms/scanline
FaxSend[5666]: MODEM Supports 20 ms, 10 ms/scanline
FaxSend[5666]: MODEM Supports 20 ms/scanline
FaxSend[5666]: MODEM Supports 40 ms, 20 ms/scanline
FaxSend[5666]: MODEM Supports 40 ms/scanline
FaxSend[5666]: <-- [9:AT+FRM=?\r]
FaxSend[5666]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: MODEM LT V.92 DATA+FAX MODEM VERSION 8.30 LT V.92 
Data+Fax Modem Version 8.30/
FaxSend[5666]: <-- [5:ATM0\r]
FaxSend[5666]: --> [2:OK]
FaxSend[5666]: STATE CHANGE: BASE -> RUNNING (timeout 30)

Relevant part from config file:

Class1Cmd:        AT+FCLASS=1
Class1PPMWaitCmd:    AT+FTS=7
Class1TCFWaitCmd:    AT+FTS=7
Class1EOPWaitCmd:    AT+FTS=9
Class1SwitchingCmd:    AT+FRS=7
Class1RecvAbortOK:    200
Class1FrameOverhead:    4
Class1RecvIdentTimer:    40000
Class1TCFMaxNonZero:    10
Class1TCFMinRun:    1000

thanks,
riccardo


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*