[hylafax-users] Multitech failure to train modem at 2400 bps :

["CS Linux Support Group" <cslinux@xxxxxxxxxx>]

Hi all,
      I suppose this is familiar to those using Multitech modems.I get
this error "Failure to train modem at 2400 bps".The modem I use is
Multitech 5634 ZBA .The following is the error log generated.


Thanks for all your time,
Aravindan

	Apr 16 17:53:05.70: [11261]: SESSION BEGIN 000000218 54640
Apr 16 17:53:05.70: [11261]: HylaFAX (tm) Version 5.2.2
Apr 16 17:53:05.70: [11261]: SEND FAX: JOB 113 DEST 54640 COMMID 000000218
DEVICE '/dev/ttyS0' FROM 'cslinux <cslinux@xxxxxxxxxxxx>' USER root
Apr 16 17:53:05.70: [11261]: <-- [12:AT+FCLASS=1\r]
Apr 16 17:53:05.72: [11261]: --> [2:OK]
Apr 16 17:53:06.07: [11261]: DIAL 54640
Apr 16 17:53:06.07: [11261]: <-- [10:ATDT54640\r]
Apr 16 17:53:17.94: [11261]: --> [7:CONNECT]
Apr 16 17:53:17.96: [11261]: --> [2:OK]
Apr 16 17:53:17.96: [11261]: REMOTE NSF "00 00 25 00 00 00 92 10 4D 02 00
58 00 28 00 A0 80 80 B1 60 63 93"
Apr 16 17:53:17.96: [11261]: NSF remote fax equipment: Ricoh
Apr 16 17:53:17.96: [11261]: <-- [9:AT+FRH=3\r]
Apr 16 17:53:18.38: [11261]: --> [7:CONNECT]
Apr 16 17:53:18.39: [11261]: --> [2:OK]
Apr 16 17:53:18.39: [11261]: REMOTE best rate 33600 bit/s
Apr 16 17:53:18.39: [11261]: REMOTE max A3 page width (303 mm)
Apr 16 17:53:18.39: [11261]: REMOTE max unlimited page length
Apr 16 17:53:18.39: [11261]: REMOTE best vres 200 x 200 dpi
Apr 16 17:53:18.39: [11261]: REMOTE format support: MH, MR, MMR, JBIG
Apr 16 17:53:18.39: [11261]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 16 17:53:18.39: [11261]: REMOTE best 10 ms/scanline
Apr 16 17:53:18.39: [11261]: USE 14400 bit/s
Apr 16 17:53:18.39: [11261]: USE error correction mode
Apr 16 17:53:18.39: [11261]: SEND file "docq/cover113;f0"
Apr 16 17:53:18.39: [11261]: USE A4 page width (215 mm)
Apr 16 17:53:18.39: [11261]: USE unlimited page length
Apr 16 17:53:18.39: [11261]: USE 3.85 line/mm
Apr 16 17:53:18.39: [11261]: USE 2-D MMR
Apr 16 17:53:18.39: [11261]: USE 0 ms/scanline
Apr 16 17:53:18.39: [11261]: SEND training at v.17 14400 bit/s
Apr 16 17:53:18.39: [11261]: <-- [9:AT+FRS=7\r]
Apr 16 17:53:18.54: [11261]: --> [2:OK]
Apr 16 17:53:18.54: [11261]: <-- [9:AT+FTH=3\r]
Apr 16 17:53:24.51: [11261]: --> [7:CONNECT]
Apr 16 17:53:24.51: [11261]: --> [5:ERROR]
Apr 16 17:53:24.52: [11261]: MODEM Command error
Apr 16 17:53:24.52: [11261]: Error sending T.30 prologue frames
Apr 16 17:53:24.52: [11261]: SEND training at v.17 12000 bit/s
Apr 16 17:53:24.52: [11261]: <-- [9:AT+FRS=7\r]
Apr 16 17:53:24.78: [11261]: --> [2:OK]
Apr 16 17:53:24.78: [11261]: <-- [9:AT+FTH=3\r]
Apr 16 17:53:30.75: [11261]: --> [7:CONNECT]
Apr 16 17:53:30.76: [11261]: --> [5:ERROR]
Apr 16 17:53:30.76: [11261]: MODEM Command error
Apr 16 17:53:30.76: [11261]: Error sending T.30 prologue frames
Apr 16 17:53:30.76: [11261]: SEND training at v.29 9600 bit/s
Apr 16 17:53:30.76: [11261]: <-- [9:AT+FRS=7\r]
Apr 16 17:53:31.02: [11261]: --> [2:OK]
Apr 16 17:53:31.02: [11261]: <-- [9:AT+FTH=3\r]
Apr 16 17:53:36.99: [11261]: --> [7:CONNECT]
Apr 16 17:53:36.99: [11261]: --> [5:ERROR]
Apr 16 17:53:36.99: [11261]: MODEM Command error
Apr 16 17:53:36.99: [11261]: Error sending T.30 prologue frames
Apr 16 17:53:36.99: [11261]: SEND training at v.29 7200 bit/s
Apr 16 17:53:36.99: [11261]: <-- [9:AT+FRS=7\r]
Apr 16 17:53:37.26: [11261]: --> [2:OK]
Apr 16 17:53:37.26: [11261]: <-- [9:AT+FTH=3\r]
Apr 16 17:53:43.23: [11261]: --> [7:CONNECT]
Apr 16 17:53:43.23: [11261]: --> [5:ERROR]
Apr 16 17:53:43.23: [11261]: MODEM Command error
Apr 16 17:53:43.23: [11261]: Error sending T.30 prologue frames
Apr 16 17:53:43.23: [11261]: SEND training at v.27ter 4800 bit/s
Apr 16 17:53:43.23: [11261]: <-- [9:AT+FRS=7\r]
Apr 16 17:53:43.50: [11261]: --> [2:OK]
Apr 16 17:53:43.50: [11261]: <-- [9:AT+FTH=3\r]
Apr 16 17:53:49.47: [11261]: --> [7:CONNECT]
Apr 16 17:53:49.47: [11261]: --> [5:ERROR]
Apr 16 17:53:49.47: [11261]: MODEM Command error
Apr 16 17:53:49.47: [11261]: Error sending T.30 prologue frames
Apr 16 17:53:49.47: [11261]: SEND training at v.27ter fallback mode 2400
bit/s
Apr 16 17:53:49.47: [11261]: <-- [9:AT+FRS=7\r]
Apr 16 17:53:49.74: [11261]: --> [2:OK]
Apr 16 17:53:49.74: [11261]: <-- [9:AT+FTH=3\r]
Apr 16 17:53:55.71: [11261]: --> [7:CONNECT]
Apr 16 17:53:55.71: [11261]: --> [5:ERROR]
Apr 16 17:53:55.71: [11261]: MODEM Command error
Apr 16 17:53:55.71: [11261]: Error sending T.30 prologue frames
Apr 16 17:53:55.71: [11261]: TRAINING failed
Apr 16 17:53:55.71: [11261]: <-- [9:AT+FRS=7\r]
Apr 16 17:53:55.98: [11261]: --> [2:OK]
Apr 16 17:53:55.98: [11261]: <-- [9:AT+FTH=3\r]
Apr 16 17:54:01.94: [11261]: --> [7:CONNECT]
Apr 16 17:54:01.95: [11261]: --> [5:ERROR]
Apr 16 17:54:01.95: [11261]: MODEM Command error
Apr 16 17:54:02.95: [11261]: <-- [5:ATH0\r]
Apr 16 17:54:03.30: [11261]: --> [2:OK]
Apr 16 17:54:03.30: [11261]: SESSION END


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*