 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Strange: gaps in output at receiver
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Strange: gaps in output at receiver
- From: Walter Hop <hylafax@xxxxxxxxxxxxxxxxxx>
- Date: Tue, 19 Feb 2008 13:50:56 +0100
Hi all,
I'm having a strange issue between our Hylafax sender, and some particular remote set...
What consistently seems to happen (for this recipient) is that several gaps from the page are left out. There are no error messages as far as I can see.
A message as the recipient received it: http://u.lfms.nl/fax_missing_lines.gif
You can see what is left out at the original message: http://u.lfms.nl/fax_original.gif
As you can see, there are three vertical regions which are not printed out at the remote site at all...
The session transcript is below this message.
Any ideas/debugging tips?
Kind regards, WH
Feb 18 17:29:06.09: [25339]: SESSION BEGIN 000003784 +xxxxxxxxxxx
Feb 18 17:29:06.09: [25339]: HylaFAX (tm) Version 5.2.1
Feb 18 17:29:06.09: [25339]: SEND FAX: JOB 1837 DEST 00xxxxxxxxxxx COMMID 000003784 DEVICE '/dev/cuad0' FROM 'fax1.intern <www@xxxxxxxxxxx>' USER www
Feb 18 17:29:06.09: [25339]: <-- [12:AT+FCLASS=1\r]
Feb 18 17:29:06.11: [25339]: --> [2:OK]
Feb 18 17:29:06.11: [25339]: DIAL 00xxxxxxxxxxx
Feb 18 17:29:06.11: [25339]: <-- [18:ATDT00xxxxxxxxxxx\r]
Feb 18 17:29:35.18: [25339]: --> [7:CONNECT]
Feb 18 17:29:36.97: [25339]: --> [2:OK]
Feb 18 17:29:36.97: [25339]: REMOTE CSI "+41 xxxxxxxxx"
Feb 18 17:29:36.97: [25339]: <-- [9:AT+FRH=3\r]
Feb 18 17:29:36.99: [25339]: --> [7:CONNECT]
Feb 18 17:29:37.24: [25339]: --> [2:OK]
Feb 18 17:29:37.24: [25339]: REMOTE best rate 9600 bit/s
Feb 18 17:29:37.24: [25339]: REMOTE max A4 page width (215 mm)
Feb 18 17:29:37.24: [25339]: REMOTE max unlimited page length
Feb 18 17:29:37.24: [25339]: REMOTE best vres 7.7 line/mm
Feb 18 17:29:37.24: [25339]: REMOTE format support: MH, MR
Feb 18 17:29:37.24: [25339]: REMOTE best 20 ms, 10 ms/scanline
Feb 18 17:29:37.24: [25339]: USE 9600 bit/s
Feb 18 17:29:37.24: [25339]: SEND file "docq/doc1838.pdf;40"
Feb 18 17:29:37.24: [25339]: USE A4 page width (215 mm)
Feb 18 17:29:37.24: [25339]: USE unlimited page length
Feb 18 17:29:37.24: [25339]: USE 3.85 line/mm
Feb 18 17:29:37.24: [25339]: USE 2-D MR
Feb 18 17:29:37.24: [25339]: USE 20 ms/scanline
Feb 18 17:29:37.24: [25339]: SEND training at v.29 9600 bit/s
Feb 18 17:29:37.24: [25339]: <-- [9:AT+FRS=7\r]
Feb 18 17:29:37.32: [25339]: --> [2:OK]
Feb 18 17:29:37.32: [25339]: <-- [9:AT+FTH=3\r]
Feb 18 17:29:38.18: [25339]: --> [7:CONNECT]
Feb 18 17:29:38.18: [25339]: <-- data [23]
Feb 18 17:29:38.19: [25339]: <-- data [2]
Feb 18 17:29:38.21: [25339]: --> [7:CONNECT]
Feb 18 17:29:38.21: [25339]: <-- data [6]
Feb 18 17:29:38.21: [25339]: <-- data [2]
Feb 18 17:29:39.32: [25339]: --> [2:OK]
Feb 18 17:29:39.32: [25339]: <-- [9:AT+FTS=7\r]
Feb 18 17:29:39.38: [25339]: --> [2:OK]
Feb 18 17:29:39.38: [25339]: <-- [10:AT+FTM=96\r]
Feb 18 17:29:39.40: [25339]: --> [7:CONNECT]
Feb 18 17:29:39.40: [25339]: <-- data [1024]
Feb 18 17:29:39.40: [25339]: <-- data [776]
Feb 18 17:29:39.40: [25339]: <-- data [2]
Feb 18 17:29:41.18: [25339]: --> [2:OK]
Feb 18 17:29:41.18: [25339]: <-- [9:AT+FRH=3\r]
Feb 18 17:29:42.89: [25339]: --> [7:CONNECT]
Feb 18 17:29:44.27: [25339]: --> [2:OK]
Feb 18 17:29:44.27: [25339]: TRAINING succeeded
Feb 18 17:29:44.27: [25339]: <-- [9:AT+FRS=7\r]
Feb 18 17:29:44.36: [25339]: --> [2:OK]
Feb 18 17:29:44.36: [25339]: <-- [10:AT+FTM=96\r]
Feb 18 17:29:44.37: [25339]: --> [7:CONNECT]
Feb 18 17:29:44.38: [25339]: SEND begin page
Feb 18 17:29:44.38: [25339]: <-- data [1028]
Feb 18 17:29:44.38: [25339]: <-- data [1024]
Feb 18 17:29:44.38: [25339]: <-- data [1025]
Feb 18 17:29:45.39: [25339]: <-- data [1031]
Feb 18 17:29:45.39: [25339]: <-- data [1029]
Feb 18 17:29:46.41: [25339]: <-- data [1027]
Feb 18 17:29:46.41: [25339]: <-- data [1028]
Feb 18 17:29:47.47: [25339]: <-- data [1030]
Feb 18 17:29:47.47: [25339]: <-- data [1028]
Feb 18 17:29:48.53: [25339]: <-- data [1030]
Feb 18 17:29:48.53: [25339]: <-- data [1029]
Feb 18 17:29:49.73: [25339]: <-- data [1032]
Feb 18 17:29:49.73: [25339]: <-- data [1029]
Feb 18 17:29:50.80: [25339]: <-- data [1029]
Feb 18 17:29:50.80: [25339]: <-- data [1029]
Feb 18 17:29:51.86: [25339]: <-- data [1024]
Feb 18 17:29:51.86: [25339]: <-- data [1027]
Feb 18 17:29:52.93: [25339]: <-- data [1028]
Feb 18 17:29:52.93: [25339]: <-- data [1029]
Feb 18 17:29:53.99: [25339]: <-- data [1029]
Feb 18 17:29:53.99: [25339]: <-- data [1030]
Feb 18 17:29:55.05: [25339]: <-- data [1027]
Feb 18 17:29:55.05: [25339]: <-- data [1032]
Feb 18 17:29:56.25: [25339]: <-- data [1029]
Feb 18 17:29:56.25: [25339]: <-- data [1036]
Feb 18 17:29:57.32: [25339]: <-- data [1029]
Feb 18 17:29:57.32: [25339]: <-- data [856]
Feb 18 17:29:58.38: [25339]: SENT 27475 bytes of data
Feb 18 17:29:58.38: [25339]: <-- data [1025]
Feb 18 17:29:58.38: [25339]: <-- data [1024]
Feb 18 17:29:59.58: [25339]: <-- data [1024]
Feb 18 17:29:59.58: [25339]: <-- data [1024]
Feb 18 17:29:59.58: [25339]: <-- data [1024]
Feb 18 17:30:00.64: [25339]: <-- data [12]
Feb 18 17:30:00.64: [25339]: SENT 5132 bytes of data
Feb 18 17:30:00.64: [25339]: SEND 2D RTC
Feb 18 17:30:00.64: [25339]: <-- data [30]
Feb 18 17:30:00.64: [25339]: <-- data [2]
Feb 18 17:30:00.64: [25339]: SEND end page
Feb 18 17:30:04.35: [25339]: --> [2:OK]
Feb 18 17:30:04.35: [25339]: <-- [9:AT+FTS=9\r]
Feb 18 17:30:04.43: [25339]: --> [2:OK]
Feb 18 17:30:04.43: [25339]: SEND send EOP (no more pages or documents)
Feb 18 17:30:04.43: [25339]: <-- [9:AT+FTH=3\r]
Feb 18 17:30:05.30: [25339]: --> [7:CONNECT]
Feb 18 17:30:05.30: [25339]: <-- data [3]
Feb 18 17:30:05.30: [25339]: <-- data [2]
Feb 18 17:30:05.62: [25339]: --> [2:OK]
Feb 18 17:30:05.62: [25339]: <-- [9:AT+FRH=3\r]
Feb 18 17:30:07.26: [25339]: --> [7:CONNECT]
Feb 18 17:30:08.67: [25339]: --> [2:OK]
Feb 18 17:30:08.67: [25339]: SEND recv MCF (message confirmation)
Feb 18 17:30:08.67: [25339]: <-- [9:AT+FRS=7\r]
Feb 18 17:30:08.67: [25339]: SEND FAX (000003784): FROM www@xxxxxxxxxxx TO 00xxxxxxxxxxx (page 1 of 1 sent in 0:00:31)
Feb 18 17:30:08.75: [25339]: --> [2:OK]
Feb 18 17:30:08.75: [25339]: SEND FAX (000003784): FROM www@xxxxxxxxxxx TO 00xxxxxxxxxxx (docq/doc1838.pdf;40 sent in 0:00:31)
Feb 18 17:30:09.70: [25339]: <-- [9:AT+FTH=3\r]
Feb 18 17:30:10.56: [25339]: --> [7:CONNECT]
Feb 18 17:30:10.56: [25339]: <-- data [3]
Feb 18 17:30:10.56: [25339]: <-- data [2]
Feb 18 17:30:10.88: [25339]: --> [2:OK]
Feb 18 17:30:11.91: [25339]: <-- [5:ATH0\r]
Feb 18 17:30:12.70: [25339]: --> [2:OK]
Feb 18 17:30:12.70: [25339]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Strange: gaps in output at receiver
- From: Lee Howard
- Re: [hylafax-users] Strange: gaps in output at receiver
- Prev by Date: Re: [hylafax-users] Hylafax 4.4.4 on SuSE 10.0 with Eicon Diva Server 4BRI 8M: How to set specific "from"-Address
- Next by Date: Re: [hylafax-users] Strange: gaps in output at receiver
- Previous by thread: [hylafax-users] sending with different msn/ddi capi4hylafax and
- Next by thread: Re: [hylafax-users] Strange: gaps in output at receiver
- Index(es):
Project hosted by iFAX Solutions