[hylafax-users] Problems with resolution

["Moritz Winterberg" <winterberg@xxxxxxxxxx>]

Hi,

I'm trying to send a fax to myself using an EICON DIVA PRI card.
The output tells me I can send but not receive in high resolution mode:

[High resolution document is not supported by client..]

any idea how to tell the modem to use high res mode ? Do I have to set
some AT command in the modem config ?

thanks
Moritz

------ OUTPUT LOG -------
Apr 24 20:04:37.97: [20556]: SESSION BEGIN 000000007 +492213553352889
Apr 24 20:04:37.97: [20556]: HylaFAX (tm) Version 5.1.3
Apr 24 20:04:37.97: [20556]: SEND FAX: JOB 5 DEST 49221355335xxxx
COMMID 000000007 DEVICE '/dev/ttyds06' FROM 'root <root@bierfask01>'
USER root
Apr 24 20:04:37.97: [20556]: STATE CHANGE: RUNNING -> SENDING
Apr 24 20:04:37.97: [20556]: Apply DialString rules to "49221355335xxxx"
Apr 24 20:04:37.97: [20556]: --> return result "49221355335xxxx"
Apr 24 20:04:37.99: [20556]: <-- [10:AT+FBOR=0\r]
Apr 24 20:04:37.99: [20556]: --> [2:OK]
Apr 24 20:04:37.99: [20556]: <-- [13:AT+FPHCTO=30\r]
Apr 24 20:04:37.99: [20556]: --> [5:ERROR]
Apr 24 20:04:37.99: [20556]: MODEM Command error
Apr 24 20:04:37.99: [20556]: <-- [10:AT+FBUG=1\r]
Apr 24 20:04:37.99: [20556]: --> [2:OK]
Apr 24 20:04:37.99: [20556]: <-- [24:AT+FDCC=7,D,2,2,0,2,0,0\r]
Apr 24 20:04:37.99: [20556]: --> [2:OK]
Apr 24 20:04:38.01: [20556]: <-- [15:AT+IO7300090E9\r]
Apr 24 20:04:38.01: [20556]: --> [2:OK]
Apr 24 20:04:38.01: [20556]: DIAL 492213553352889
Apr 24 20:04:38.01: [20556]: <-- [20:ATDT492213553352xxx\r]
Apr 24 20:05:02.31: [20556]: --> [19:ATDT49221355335xxx]
Apr 24 20:05:02.31: [20556]: --> [5:+FCON]
Apr 24 20:05:02.31: [20556]: --> [28:+FCSI:"test       "]
Apr 24 20:05:02.31: [20556]: REMOTE CSI "test"
Apr 24 20:05:02.31: [20556]: --> [22:+FDIS: 0,8,2,2,0,2,0,0]
Apr 24 20:05:02.31: [20556]: --> [2:OK]
Apr 24 20:05:02.31: [20556]: REMOTE best rate 21600 bit/s
Apr 24 20:05:02.31: [20556]: REMOTE max A3 page width (303 mm)
Apr 24 20:05:02.31: [20556]: REMOTE max unlimited page length
Apr 24 20:05:02.31: [20556]: REMOTE best vres 3.85 line/mm
Apr 24 20:05:02.31: [20556]: REMOTE format support: MH
Apr 24 20:05:02.31: [20556]: REMOTE supports T.30 Annex C, half duplex ECM
Apr 24 20:05:02.31: [20556]: REMOTE best 0 ms/scanline
Apr 24 20:05:02.31: [20556]: USE 21600 bit/s
Apr 24 20:05:02.31: [20556]: USE error correction mode
Apr 24 20:05:02.31: [20556]: SEND file
"docq/doc.bierfask01.1177437866205387086;31"
Apr 24 20:05:02.31: [20556]: High resolution document is not supported
by client, image resolution 7.71654 lines/mm {E414}
Apr 24 20:05:03.31: [20556]: <-- [5:ATH0\r]
Apr 24 20:05:03.31: [20556]: --> [4:ATH0]
Apr 24 20:05:03.31: [20556]: --> [2:OK]
Apr 24 20:05:03.31: [20556]: MODEM set DTR OFF
Apr 24 20:05:03.31: [20556]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Apr 24 20:05:03.31: [20556]: SESSION END
------------------------------------------------------------------------------------------

--------------- INCOMING LOG ---------------------------------------------------
Apr 24 20:04:50.19: [ 6209]: SESSION BEGIN 000000008
Apr 24 20:04:50.19: [ 6209]: HylaFAX (tm) Version 5.1.3
Apr 24 20:04:50.19: [ 6209]: CallID: '5335xxx' '002115800xxxxx'
Apr 24 20:04:50.19: [ 6209]: <-- [4:ATA\r]
Apr 24 20:04:50.19: [ 6209]: --> [18:CID: 002115800xxxx]
Apr 24 20:04:50.19: [ 6209]: --> [14:DAD: 53352xxxx]
Apr 24 20:04:50.19: [ 6209]: --> [4:RING]
Apr 24 20:05:03.84: [ 6209]: --> [8:+FHNG: 1]
Apr 24 20:05:03.84: [ 6209]: REMOTE HANGUP: Ring detect without
successful handshake (code 1)
Apr 24 20:05:03.84: [ 6209]: ANSWER: Ring detected without successful
handshake {E012}
Apr 24 20:05:03.84: [ 6209]: SESSION END

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*