[hylafax-users] Hylafax never answers incoming call. Always Listening to rings.

[borgo2000@xxxxxxxx]

Hi to everybody
I have spent the last two days on the following problem without any success.
My Hylafax nevere answer to incoming call. It's always listening to rings
but never answer.


When my modem rings.....

#faxstat

Listening to rings from modem

but hylafax does't answer

The syslog trace is:

2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: DELAY 2600 ms 

2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM set DTR
ON  
2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: DELAY 75 ms  
2007-01-08 11:37:34 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM set DTR
OFF  
2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM set DTR
OFF  
2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: --> [2:OK]  
2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: <-- [5:ATH0\r]
 
2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: MODEM TIMEOUT:
reading line from modem  
2007-01-08 11:37:32 Local4.Info 192.168.0.107 FaxGetty[3017]: --> [6:RING A]
 
2007-01-08 11:37:18 Local4.Info 192.168.0.107 FaxGetty[3017]: --> [6:RING A]
 
2007-01-08 11:37:18 Local4.Info 192.168.0.107 FaxGetty[3017]: STATE CHANGE:
RUNNING -> LISTENING  

If I use the faxanswer command everything is OK, and I get my fax. 
But I'd like to use the auto-answer with faxgetty.


Some notes about my config:

1) I use CentOs 4.4 with USR 56k Professional Message modem

2) After faxsetup I get two warnings !!! 

Warning: /bin/vgetty does not exist or is not an executable program!
Warning: /bin/egetty does not exist or is not an executable program!

3) In  /etc/inittab I have:

mo:2345:respawn:/usr/sbin/faxgetty ttyS0

4) My config.ttyS0 is:

# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and XON/XOFF flow control. 
#
#
LogFacility:            local4
CountryCode:            39
AreaCode:               0721
FAXNumber:              0721.0000
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules.europe
#ServerTracing:         1
ServerTracing:          0xfff
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          medium
GettyArgs:              "-h %l dx_%s"
#GettyArgs:             "-t 20 -h %l F%s"
LocalIdentifier:        FaxServer
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              19200           # rate for DCE-DTE communication
#ModemRate:             57600
ModemFlowControl:       xonxoff         # software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or
not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow
control
Class1SFLOCmd:          ""              # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for
response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
#
# When using AT+FRS=n we see USR modems reset themselves in the middle of
sessions
# this is not good.  So, we seem to work-around that problem by not using
the
# command.  Unfortunately, this isn't an ideal thing.
#
Class1SwitchingCmd:     "<delay\0727>"




Regards and greetings from Italy

Andrea 
 --
 Email.it, the professional e-mail, gratis per te: http://www.email.it/f
 
 Sponsor:
 Ariatel Vocepiù Ricaricabile: nessun canone, nessun costo mensile, paghi
solo le telefonate e a solo 1,15 cent/min per tutti i numeri fissi d?Italia!
 Clicca qui: http://adv.email.it/cgi-bin/foclick.cgi?mid=5833&d=20070108



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*