Re: [hylafax-users] Direct Inward Dial based routing with FaxDispatch

["Suraj Jadhav" <sunracesuraj@xxxxxxxxxxxxxx>]

Hello,

I tried with the config below and got this error...

May 23 14:02:15.38: [ 3224]: SESSION BEGIN 000000367 001xxxxxx
May 23 14:02:15.38: [ 3224]: HylaFAX (tm) Version 4.2.5
May 23 14:02:15.38: [ 3224]: SEND FAX: JOB 229 DEST 2218 COMMID 000000367 DEVICE '/dev/ttyS0' FROM 'someone <someone@xxxxxxxxxxxxxx>' USER fax
May 23 14:02:15.38: [ 3224]: <-- [9:AT+FLO=2\r]
May 23 14:02:15.51: [ 3224]: --> [2:OK]
May 23 14:02:15.51: [ 3224]: <-- [9:AT+FPP=0\r]
May 23 14:02:15.64: [ 3224]: --> [2:OK]
May 23 14:02:15.64: [ 3224]: <-- [9:AT+FBO=0\r]
May 23 14:02:15.77: [ 3224]: --> [2:OK]
May 23 14:02:15.77: [ 3224]: <-- [10:AT+FCT=30\r]
May 23 14:02:15.91: [ 3224]: --> [2:OK]
May 23 14:02:15.91: [ 3224]: <-- [15:AT+FNR=1,1,1,0\r]
May 23 14:02:16.04: [ 3224]: --> [2:OK]
May 23 14:02:16.04: [ 3224]: <-- [9:AT+FIE=0\r]
May 23 14:02:16.17: [ 3224]: --> [2:OK]
May 23 14:02:16.17: [ 3224]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
May 23 14:02:16.31: [ 3224]: --> [2:OK]
May 23 14:02:16.31: [ 3224]: DIAL 2218
May 23 14:02:16.31: [ 3224]: <-- [9:ATDT2218\r]
May 23 14:03:11.41: [ 3224]: --> [10:NO CARRIER]
May 23 14:03:11.41: [ 3224]: SEND FAILED: JOB 229 DEST 2218 ERR No carrier detected
May 23 14:03:11.41: [ 3224]: <-- [5:ATH0\r]
May 23 14:03:11.54: [ 3224]: --> [2:OK]
May 23 14:03:11.54: [ 3224]: SESSION END



On Tue, 23 May 2006 Lee Howard wrote :
>The hylafax-config man page nearly spells-out how to do DID via PBX DTMF:
>
>The special *CallID* value of "SHIELDED_DTMF" is used in conjunction with *ModemRingResponse* and *CallIDAnswerLength.* After executing *ModemRingResponse,* HylaFAX will expect DTMF data (usually DLE-shielded) for *CallIDn* until *CallIDAnswerLength* is reached. Note that if the modem is in voice mode to hear these DTMF digits, then it must be returned to fax mode in the *ModemAnswerCmd.* In order to prevent this feature from losing incoming fax calls, if fax sender CNG is detected while waiting for DTMF or if ten seconds elapse without sufficient DTMF then the remaining expected digits will be populated by whitespace, triggering fax answering.
>
>For example, the following settings will cause HylaFAX to enter voice mode and go off-hook when a RING is detected. It will then expect four DTMF digits (presumably for routing), and then it will pause for 100 ms before returning to fax mode and answering the call.
>
>  ModemRingResponse:    AT+FCLASS=8;H1
>  CallIDPattern:        SHIELDED_DTMF
>  CallIDAnswerLength:    4
>  ModemAnswerCmd:        <delay:100>AT+FCLASS=1;A
>
>
>Lee.
>
>____________________ HylaFAX(tm) Users Mailing List _______________________
>  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>

Thanks & Regards
Suraj Jadhav