[hylafax-users] some difficulties to send fax

[Olivier Saulnier <steganux@xxxxxxxxxxxx>]

Hello,

I have configured a Hylafax server, and use and MultitechModem mt5656.
Hylafax detect it as a class1 modem.

When i send faxes, the log message is ok:
mai 09 14:45:41.10: [30188]: SESSION BEGIN 00000009 3348051
mai 09 14:45:41.10: [30188]: HylaFAX (tm) Version 4.1.5
mai 09 14:45:41.10: [30188]: SEND FAX: JOB 7 DEST 8051 COMMID 00000009 
DEVICE '/
dev/cua0'
mai 09 14:45:41.10: [30188]: DELAY 75 ms
mai 09 14:45:41.18: [30188]: DELAY 2600 ms
mai 09 14:45:43.78: [30188]: DELAY 10 ms
mai 09 14:45:43.79: [30188]: <-- [4:ATZ\r]
mai 09 14:45:44.23: [30188]: --> [2:OK]
mai 09 14:45:44.23: [30188]: DELAY 3000 ms
mai 09 14:45:47.23: [30188]: <-- [5:ATE0\r]
mai 09 14:45:47.28: [30188]: --> [4:ATE0]
mai 09 14:45:47.28: [30188]: --> [2:OK]
mai 09 14:45:47.28: [30188]: <-- [5:ATV1\r]
mai 09 14:45:47.33: [30188]: --> [2:OK]
mai 09 14:45:47.33: [30188]: <-- [5:ATQ0\r]
mai 09 14:45:47.38: [30188]: --> [2:OK]
mai 09 14:45:47.38: [30188]: <-- [7:ATS0=0\r]
mai 09 14:45:47.45: [30188]: --> [2:OK]
mai 09 14:45:47.45: [30188]: <-- [7:ATS8=2\r]
mai 09 14:45:47.52: [30188]: --> [2:OK]
mai 09 14:45:47.52: [30188]: <-- [8:ATS7=60\r]
mai 09 14:45:47.59: [30188]: --> [2:OK]
mai 09 14:45:47.59: [30188]: <-- [12:AT+FCLASS=1\r]
mai 09 14:45:47.64: [30188]: --> [2:OK]
mai 09 14:45:47.64: [30188]: <-- [5:ATM0\r]
mai 09 14:45:47.69: [30188]: --> [2:OK]
mai 09 14:45:47.69: [30188]: <-- [12:AT+FCLASS=1\r]
mai 09 14:45:47.84: [30188]: --> [2:OK]
mai 09 14:45:47.84: [30188]: DIAL 8051
mai 09 14:45:47.84: [30188]: <-- [9:ATDT8051\r]
mai 09 14:46:05.40: [30188]: --> [7:CONNECT]
mai 09 14:46:06.88: [30188]: --> [2:OK]
mai 09 14:46:06.88: [30188]: REMOTE NSF "59 01 02 20 20 20 20 20 20 20 
20 20 20
20 20 20 20 20 20 20 20 20 20 C4 00 16 BA"
mai 09 14:46:06.88: [30188]: NSF remote fax equipment: unknown
mai 09 14:46:06.88: [30188]: NSF possible remote station ID: "
?"
mai 09 14:46:06.88: [30188]: <-- [9:AT+FRH=3\r]
mai 09 14:46:06.95: [30188]: --> [7:CONNECT]
mai 09 14:46:07.58: [30188]: --> [2:OK]
mai 09 14:46:07.58: [30188]: REMOTE CSI ""
mai 09 14:46:07.58: [30188]: <-- [9:AT+FRH=3\r]
mai 09 14:46:07.65: [30188]: --> [7:CONNECT]
mai 09 14:46:07.84: [30188]: --> [2:OK]
mai 09 14:46:07.84: [30188]: REMOTE best rate 14400 bit/s
mai 09 14:46:07.84: [30188]: REMOTE max page width 1728 pixels in 215 mm
mai 09 14:46:07.84: [30188]: REMOTE max unlimited page length
mai 09 14:46:07.84: [30188]: REMOTE best vres 7.7 line/mm
mai 09 14:46:07.84: [30188]: REMOTE best format 2-D MMR
mai 09 14:46:07.84: [30188]: REMOTE supports T.30 Annex A, ECM
mai 09 14:46:07.84: [30188]: REMOTE best 5 ms/scanline
mai 09 14:46:07.84: [30188]: USE 14400 bit/s
mai 09 14:46:07.84: [30188]: USE 5 ms/scanline
mai 09 14:46:07.84: [30188]: <-- [9:AT+FTH=3\r]
mai 09 14:46:07.93: [30188]: --> [7:CONNECT]
mai 09 14:46:07.93: [30188]: <-- data [3]
mai 09 14:46:07.93: [30188]: <-- data [2]
mai 09 14:46:09.23: [30188]: --> [2:OK]
mai 09 14:46:09.23: [30188]: <-- [5:ATH0\r]
mai 09 14:46:10.23: [30188]: --> [2:OK]
mai 09 14:46:10.23: [30188]: SESSION END


But no fax is received at the other side. Only the fax answer, and write 
a message on screen: error receipt. I try with to differents faxs.

My fax configuration file is the following:
*CountryCode: 33
AreaCode: 4
FAXNumber: 0470028057
LongDistancePrefix: 00
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "STEGANUX"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25

ModemType: Class1 # use this to supply a hint

Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendMsgDelay: 75 # 75ms delay after training
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration

I have no problem at reception of fax.
Do you have any idea??

Best regards,
*

--
Olivier Saulnier
STEGANUX
35 Quai Louis Blanc
03100 Montluçon
T: 04.70.02.80.55
F: 04.70.02.80.57
http://www.steganux.com


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*