[hylafax-users] Faxgetty cannot init modem, but probemodem works.

[jeff leads <jleads@xxxxxxxxx>]

I have a USR Courier V.Everything attached to a Digi
Portserver TS8, I'm running a new install of Redhat
ES4 and Hylafax 4.2.5 (installed using RPM).  I cant
seem to figure out why faxgetty can't speak to the
modem to initialize it.  I set logging to 0xfff
(output below).  I have also tried differnt ports on
the portserver with the same result.  Probemodem works
fine however (output below).  I have attached my
config.tty407 (output below).

Can some one point me in the right direction?  

Thanks a bunch

Jeff


[root@server2 etc]# ls -la /dev/tty407
crw-rw-rw-  1 uucp root 251, 7 May  6 15:01
/dev/tty407



[root@server2 ~]# probemodem tty407
Now we are going to probe the tty port.  This takes a
few seconds,
so be patient.  Note that if you do not have the modem
cabled to
the port, or the modem is turned off, this may hang
(just go and
cable up the modem or turn it on, or whatever).

Probing for best speed to talk to modem: 38400 OK.

This looks like a Class 1 and 2.0 modem.

ATI0    RESULT = "OK"   RESPONSE = "5608A"
ATI1    RESULT = "E77B" RESPONSE = "E77B"
ATI2    RESULT = "OK"   RESPONSE = "OK"
ATI3    RESULT = "OK"   RESPONSE = "USRobotics Courier
V.Everything EXT"
ATI4    RESULT = "OK"   RESPONSE = "USRobotics Courier
V.Everything Settings..."
ATI5    RESULT = "OK"   RESPONSE = "USRobotics Courier
V.Everything NVRAM Settings..."
ATI6    RESULT = "OK"   RESPONSE = "USRobotics Courier
V.Everything Link Diagnostics..."
ATI7    RESULT = "OK"   RESPONSE = "USRobotics Courier
V.Everything Configuration Profile..."
ATI8    RESULT = "ERROR"        RESPONSE = "ERROR"
ATI9    RESULT = "OK"   RESPONSE =
"(1.0USR00BA\MODEM\PNPC107\USRobotics Courier
V.Everything EXT)"




[root@server2 ~]#tail -f /var/log/messages
May  6 15:30:53 server2 FaxGetty[31028]: OPEN
/dev/tty407  HylaFAX (tm) Version 4.2.3
May  6 15:30:53 server2 FaxGetty[31028]: Purge stale
UUCP lock /var/lock/LCK..tty407
May  6 15:30:54 server2 FaxGetty[31028]: MODEM set DTR
OFF
May  6 15:30:54 server2 FaxGetty[31028]: DELAY 75 ms
May  6 15:30:55 server2 FaxGetty[31028]: MODEM set DTR
ON
May  6 15:30:55 server2 FaxGetty[31028]: DELAY 2600 ms
May  6 15:30:58 server2 FaxGetty[31028]: MODEM set
baud rate: 38400 baud, input flow RTS/CTS, output flow
RTS/CTS
May  6 15:30:58 server2 FaxGetty[31028]: DELAY 10 ms
May  6 15:30:58 server2 FaxGetty[31028]: MODEM flush
i/o
May  6 15:30:58 server2 FaxGetty[31028]: <-- [4:ATZ\r]
May  6 15:31:28 server2 FaxGetty[31028]: MODEM
TIMEOUT: reading line from modem
May  6 15:31:28 server2 FaxGetty[31028]: MODEM
<Timeout>
May  6 15:31:28 server2 FaxGetty[31028]: MODEM set DTR
OFF
May  6 15:31:28 server2 FaxGetty[31028]: DELAY 75 ms
May  6 15:31:28 server2 FaxGetty[31028]: MODEM set DTR
ON
May  6 15:31:28 server2 FaxGetty[31028]: DELAY 2600 ms
May  6 15:31:47 server2 FaxGetty[31028]: MODEM set
baud rate: 38400 baud, input flow RTS/CTS, output flow
RTS/CTS
May  6 15:31:47 server2 FaxGetty[31028]: DELAY 10 ms
May  6 15:31:47 server2 FaxGetty[31028]: MODEM flush
i/o
May  6 15:31:47 server2 FaxGetty[31028]: <-- [4:ATZ\r]
May  6 15:32:17 server2 FaxGetty[31028]: MODEM
TIMEOUT: reading line from modem



[root@server2 ~]#cat
/var/spool/hylafax/etc/config.tty407

# Configuration for using the Class 2.0 command
interface
# with a USR v.34 Courier or Sporster modem.
#
# RTS/CTS flow control is used default.
#
#
CountryCode:            1
AreaCode:               859
FAXNumber:              +1.859.544.7475
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          0xFFF
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "KRN Business FAX"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command
interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class
2.0 interface
ModemRate:              38400           # DCE-DTE
communication rate
ModemFlowControl:       rtscts          # XON/XOFF
flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem
for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem
for hardware flow control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem
for software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR
drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD
reflects carrier (or not)
ModemResultCodesCmd:    ATQ0X4          # enable
extended result codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
#ModemSetupAACmd:       AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW
MEDIUM HIGH.
# Note that we both turn the speaker on/off and set
volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add
this just
# to eliminate spurious ERROR results that confuse the
naive.
#
Class2BUGCmd:           AT+FBU=0
#
# The modem doesn't support copy quality checking,
even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we
override the query
# response so that the server will do copy quality
checking.
#
Class2CQQueryCmd:       !(0),(0)        # override
modem response
#
# Disables the reporting of bad frames by the modem. 
This
# overcomes a firmware problem in the x2 and V90
Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send
RTC itself
#
Class2SendRTC:  yes
#
# +FAP=? not supported on this modem, gives ERROR in
ServerTracing
#
Class2APQueryCmd:       none

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*