[hylafax-users] Unable to send and recieve faxes :(

[Richard Tresidder <rtresidd@xxxxxxxxxxxxxxxxxxxxxxxxx>]

Hi
   I'm having a bit of a problem with my Hylafax setup.  I've 
previously set this up identically on a FC3 system and it worked without 
a problem.
I'm now trying to get it running on a FC5_X86_64 system.
Installed using hylafax-4.2.5-1fc5.i386.rpm from the hylafax webpage
Modem is a Netcomm Roadster V.92 Model Number AM5698
MODEM ROCKWELL RC288DPi/ACF3_V1.702-V90_P21_FSH_LL

I have tried multiple configs... Using class 2, and 1. using hardware 
flowcontrol and software etc

config.ttyS0 :

CountryCode:        61
AreaCode:        8
FAXNumber:        +61.8.####.#####
LongDistancePrefix:    0
InternationalPrefix:    0011
DialStringRules:    etc/dialrules
ServerTracing:        0xFFF
SessionTracing:        0xFFF
RecvFileMode:        0664
LogFileMode:        0600
DeviceMode:        0600
RingExtended:           "DRON=2"
RingsBeforeAnswer:    3
SpeakerVolume:        quiet
GettyArgs:        "-h %l dx_%s"
LocalIdentifier:    "Tresar Electronics"
TagLineFont:        etc/lutRS18.pcf
TagLineFormat:        "From %%l|%c|Page %%P of %%T"
MaxRecvPages:        50
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:        Class1        # use this to supply a hint
ModemRate:        19200        # rate for DCE-DTE communication
ModemFlowControl:    XONXOFF        # default
#
ModemNoFlowCmd:        AT&K0        # setup no flow control
ModemHardFlowCmd:    AT&K3        # setup hardware flow control
ModemSoftFlowCmd:    AT&K4        # setup software flow control
ModemSetupDTRCmd:    AT&D2        # setup so DTR drop resets modem
ModemSetupDCDCmd:    AT&C1        # setup so DCD reflects carrier (or not)
ModemResetCmds:         AT+VDR=1,0    # disable RING message but keep 
DRON messages
#
ModemMfrQueryCmd:    !Rockwell
ModemModelQueryCmd:    !RC288DPi
ModemRevQueryCmd:    ATI3        # product information
#
ModemDialCmd:        ATDT%s        # T for tone dialing

**************    Example of a receive log     ********************

Apr 18 16:56:44.87: [14495]: SESSION BEGIN 000000260 61893137717
Apr 18 16:56:44.87: [14495]: HylaFAX (tm) Version 4.2.5
Apr 18 16:56:44.87: [14495]: MODEM set XON/XOFF/FLUSH: input ignored, 
output disabled
Apr 18 16:56:44.87: [14495]: <-- [4:ATA\r]
Apr 18 16:56:50.97: [14495]: --> [7:CONNECT]
Apr 18 16:56:50.97: [14495]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Apr 18 16:56:50.97: [14495]: STATE CHANGE: ANSWERING -> RECEIVING
Apr 18 16:56:50.97: [14495]: RECV FAX: begin
Apr 18 16:56:50.97: [14495]: <-- HDLC<32:FF C0 04 AD 00 55 12 9E 36 86 
62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 4C 74 AC>
Apr 18 16:56:50.97: [14495]: <-- data [32]
Apr 18 16:56:50.97: [14495]: <-- data [2]
Apr 18 16:56:51.16: [14495]: --> [2:]
Apr 18 16:56:51.16: [14495]: --> [2:OK]
Apr 18 16:56:51.16: [14495]: DELAY 1500 ms
Apr 18 16:56:52.66: [14495]: <-- [9:AT+FTH=3\r]
Apr 18 16:56:52.70: [14495]: --> [7:CONNECT]
Apr 18 16:56:52.70: [14495]: <-- HDLC<32:FF C0 04 AD 00 55 12 9E 36 86 
62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 4C 74 AC>
Apr 18 16:56:52.70: [14495]: <-- data [32]
Apr 18 16:56:52.70: [14495]: <-- data [2]
Apr 18 16:56:52.86: [14495]: --> [2:]
Apr 18 16:56:52.86: [14495]: --> [2:OK]
Apr 18 16:56:52.86: [14495]: DELAY 1500 ms

This just repeats until getting a No Answer (T.30 T1 timeout)

********************  One snippit of the previous FC3 receive log shows 
there is a missing CONNECT??? ****************

Jun 29 15:54:32.12: [23127]: SESSION BEGIN 000000021 61893137717
Jun 29 15:54:32.12: [23127]: HylaFAX (tm) Version 4.2.1
Jun 29 15:54:32.12: [23127]: <-- [4:ATA\r]
Jun 29 15:54:38.13: [23127]: --> [7:CONNECT]
Jun 29 15:54:38.13: [23127]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Jun 29 15:54:38.13: [23127]: RECV FAX: begin
Jun 29 15:54:38.13: [23127]: <-- data [32]
Jun 29 15:54:38.13: [23127]: <-- data [2]
Jun 29 15:54:40.05: [23127]: --> [7:CONNECT]          << This doesn't 
come in on the new system
Jun 29 15:54:40.05: [23127]: <-- data [23]
Jun 29 15:54:40.05: [23127]: <-- data [2]
Jun 29 15:54:40.88: [23127]: --> [7:CONNECT]
Jun 29 15:54:40.88: [23127]: <-- data [10]
Jun 29 15:54:40.88: [23127]: <-- data [2]
Jun 29 15:54:41.43: [23127]: --> [2:OK]
Jun 29 15:54:41.43: [23127]: <-- [9:AT+FRH=3\r]
Jun 29 15:54:41.86: [23127]: --> [7:CONNECT]
Jun 29 15:54:43.34: [23127]: --> [2:OK]
Jun 29 15:54:43.34: [23127]: REMOTE TSI "Fax Msg To:"

I can also include a log from /var/log/messages of the modem being 
configured if needed, however it is a bit long and there are no errors 
present in it

Thanks and sorry about the length

Richard Tresidder



____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*