Re: [hylafax-users] Problem to receive fax

["Andrew Rinaldi" <andrew.rinaldi@xxxxxxxxxxxx>]

Hi Luca.

Please try Class 1.

Regards

ANDREW RINALDI
Mainpine Support
USA +1 718 701 2422 | Asia/Europe +44 1225 436137 
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com 

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Pignedoli Luca
Sent: 10 February 2006 08:24
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Problem to receive fax

Hi all.

I have install hyalfax server 4.2.5 on Debian 3.1 and i have connected a
modem:

"MODEM VENUS V.90 KFAV173 SERIAL "VERSION 1.04 / 14.07.2000" Venus V.90
kfav173 Serial "Version 1.04"

When i receive a fax the communication terminated whith this error:

An attempt to receive facsimile on ttyS0 failed because:

    Unspecified Phase C error, including too much delay between TCF and +FDR
command

    ---- Transcript of session follows ----

Feb 10 14:57:43.19: [ 8557]: SESSION BEGIN 000000247 xxxxxxxxxxxx Feb 10
14:57:43.19: [ 8557]: HylaFAX (tm) Version 4.2.5 Feb 10 14:57:43.20: [
8557]: <-- [4:ATA\r] Feb 10 14:57:52.32: [ 8557]: --> [5:+FCON] Feb 10
14:57:52.32: [ 8557]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Feb 10 14:57:52.32: [ 8557]: RECV FAX: begin
Feb 10 14:57:52.35: [ 8557]: --> [28:+FTSI:"    0039 xxxx xxxxxx"]
Feb 10 14:57:52.35: [ 8557]: REMOTE TSI "0039 xxxx xxxxxx"
Feb 10 14:57:52.58: [ 8557]: --> [21:+FDCS:0,5,0,2,0,0,0,0] Feb 10
14:57:52.58: [ 8557]: REMOTE wants 14400 bit/s Feb 10 14:57:52.58: [ 8557]:
REMOTE wants A4 page width (215 mm) Feb 10 14:57:52.58: [ 8557]: REMOTE
wants unlimited page length Feb 10 14:57:52.58: [ 8557]: REMOTE wants 3.85
line/mm Feb 10 14:57:52.58: [ 8557]: REMOTE wants 1-D MH Feb 10 14:57:52.59:
[ 8557]: --> [2:OK] Feb 10 14:57:52.59: [ 8557]: <-- [7:AT+FDR\r] Feb 10
14:57:52.62: [ 8557]: --> [8:+FCERROR] Feb 10 15:00:52.62: [ 8557]: REMOTE
HANGUP: Unspecified Phase C error, including too much delay between TCF and
+FDR command (code 90) Feb 10 15:00:52.62: [ 8557]: RECV FAX (000000247):
recvq/fax000000139.tif from 0039 xxxx xxxxxx, route to <unspecified>, 0
pages in 3:00 Feb 10 15:00:52.63: [ 8557]: RECV FAX: Unspecified Phase C
error, including too much delay between TCF and +FDR command Feb 10
15:00:52.63: [ 8557]: <-- [6:AT+FK\r] Feb 10 15:01:22.63: [ 8557]: MODEM
<Timeout> Feb 10 15:01:22.63: [ 8557]: RECV FAX (000000247): session with
0039 xxxx xxxxxx terminated abnormally: Unspecified Phase C error, including
too much delay between TCF and +FDR command Feb 10 15:01:22.63: [ 8557]:
RECV FAX: bin/faxrcvd "recvq/fax000000139.tif" "ttyS0" "000000247"
"Unspecified Phase C error, including too much delay between TCF and +FDR
command"
Feb 10 15:01:22.63: [ 8557]: RECV FAX: end Feb 10 15:01:22.63: [ 8557]:
SESSION END

This is the configuration that use:

CountryCode:		39
AreaCode:		0522
FAXNumber:		+390522948555
LongDistancePrefix:	0
InternationalPrefix:	"0 "
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Interpump Engineering"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxConsecutiveBadLines:	3
MaxRecvPages:		30
ModemType:		Class2
ModemDialCmd:           ATDT71,%s
Class2Cmd:		AT+FCLASS=2	# command to enter class 2
Class2BORCmd:		AT+FBOR=0	# bit order for phase B/C/D (direct)
Class2RELCmd:		AT+FREL=1	# byte-align EOL codes on recv
Class2CQCmd:		""		# commands to enable copy quality
proc.
Class2AbortCmd:		AT+FK		# abort session command
Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality
capabilities
Class2DCCQueryCmd:	AT+FDCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FTBC=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FPHCTO=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBUG=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLID		# set local identifier command
Class2DCCCmd:		AT+FDCC		# set modem capabilities command
Class2DISCmd:		AT+FDIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FCIG		# set polling identifier command
Class2PTSCmd:		AT+FPTS		# set post-page status command
Class2RecvDataTrigger:	""		# character sent to modem to start
recv
Class2XmitWaitForXON:	yes		# if true, wait for XON before send
Class2SPLCmd:		AT+FSPL		# set polling indicator command
Class2RecvDataTrigger:	""		# character sent to modem to start
recv
Class2XmitWaitForXON:	yes		# if true, wait for XON before send

Thanks


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*