[hylafax-users] Not receiving fax

["Ricardo J. Barrios" Díaz <ricardobarrios@xxxxxxxxxxxxxxxxxx>]

Hi all

I've recently installed an hylafax server. I can send fax, but i can't
receive it. It's my system:

System: 
  - Ubuntu Linux 5.04 x86
  - Dynalink 56PMi PCI modem (Conexant HSF 56k HSFi)
    (driver hsfmodem-6.03.00lnxt04082400full)
  - Hylafax Server / Client 4.2.0 (-16ubuntu0.1)

I get that log on receive:

[LOG]

Jul 11 11:49:38.55: [ 7775]: SESSION BEGIN 000000004 34922152660
Jul 11 11:49:38.57: [ 7775]: HylaFAX (tm) Version 4.2.0
Jul 11 11:49:38.57: [ 7775]: <-- [4:ATA\r]
Jul 11 11:49:43.91: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:43.91: [ 7775]: ANSWER: FAX CONNECTION  DEVICE
'/dev/ttySHSF0'
Jul 11 11:49:43.91: [ 7775]: RECV FAX: begin
Jul 11 11:49:44.06: [ 7775]: <-- data [32]
Jul 11 11:49:44.06: [ 7775]: <-- data [2]
Jul 11 11:49:45.60: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:45.60: [ 7775]: <-- data [23]
Jul 11 11:49:45.60: [ 7775]: <-- data [2]
Jul 11 11:49:46.31: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:46.31: [ 7775]: <-- data [10]
Jul 11 11:49:46.31: [ 7775]: <-- data [2]
Jul 11 11:49:46.92: [ 7775]: --> [2:OK]
Jul 11 11:49:46.92: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:47.06: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:48.84: [ 7775]: --> [2:OK]
Jul 11 11:49:48.84: [ 7775]: REMOTE TSI "660937"
Jul 11 11:49:48.84: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:48.87: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:49.12: [ 7775]: --> [2:OK]
Jul 11 11:49:49.12: [ 7775]: REMOTE wants 9600 bit/s
Jul 11 11:49:49.12: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:49:49.12: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:49:49.12: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:49:49.12: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:49:49.12: [ 7775]: RECV training at v.29 9600 bit/s
Jul 11 11:49:49.12: [ 7775]: <-- [10:AT+FRM=96\r]
Jul 11 11:49:49.42: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:50.98: [ 7775]: RECV: TCF 1812 bytes, 67% non-zero, 1
zero-run
Jul 11 11:49:50.98: [ 7775]: RECV: reject TCF (too many non-zero, max
10%)
Jul 11 11:49:50.98: [ 7775]: RECV: reject TCF (zero run too short, min
1200)
Jul 11 11:49:51.00: [ 7775]: --> [10:NO CARRIER]
Jul 11 11:49:51.00: [ 7775]: DELAY 75 ms
Jul 11 11:49:51.07: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:49:51.39: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:51.39: [ 7775]: <-- data [3]
Jul 11 11:49:51.39: [ 7775]: <-- data [2]
Jul 11 11:49:52.68: [ 7775]: --> [2:OK]
Jul 11 11:49:52.68: [ 7775]: TRAINING failed
Jul 11 11:49:52.68: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:52.83: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:54.59: [ 7775]: --> [2:OK]
Jul 11 11:49:54.59: [ 7775]: REMOTE TSI "660937"
Jul 11 11:49:54.59: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:54.61: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:54.89: [ 7775]: --> [2:OK]
Jul 11 11:49:54.89: [ 7775]: REMOTE wants 7200 bit/s
Jul 11 11:49:54.89: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:49:54.89: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:49:54.89: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:49:54.89: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:49:54.89: [ 7775]: RECV training at v.29 7200 bit/s
Jul 11 11:49:54.89: [ 7775]: <-- [10:AT+FRM=72\r]
Jul 11 11:49:55.19: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:56.72: [ 7775]: RECV: TCF 1332 bytes, 53% non-zero, 1
zero-run
Jul 11 11:49:56.72: [ 7775]: RECV: reject TCF (too many non-zero, max
10%)
Jul 11 11:49:56.72: [ 7775]: RECV: reject TCF (zero run too short, min
900)
Jul 11 11:49:56.74: [ 7775]: --> [10:NO CARRIER]
Jul 11 11:49:56.74: [ 7775]: DELAY 75 ms
Jul 11 11:49:56.82: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:49:57.14: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:57.14: [ 7775]: <-- data [3]
Jul 11 11:49:57.14: [ 7775]: <-- data [2]
Jul 11 11:49:58.43: [ 7775]: --> [2:OK]
Jul 11 11:49:58.43: [ 7775]: TRAINING failed
Jul 11 11:49:58.43: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:58.58: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:00.36: [ 7775]: --> [2:OK]
Jul 11 11:50:00.36: [ 7775]: REMOTE TSI "660937"
Jul 11 11:50:00.36: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:00.39: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:00.64: [ 7775]: --> [2:OK]
Jul 11 11:50:00.65: [ 7775]: REMOTE wants 4800 bit/s
Jul 11 11:50:00.65: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:50:00.65: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:50:00.65: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:50:00.65: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:50:00.65: [ 7775]: RECV training at v.27ter 4800 bit/s
Jul 11 11:50:00.65: [ 7775]: <-- [10:AT+FRM=48\r]
Jul 11 11:50:05.15: [ 7775]: --> [0:]
Jul 11 11:50:05.15: [ 7775]: MODEM <Empty line>
Jul 11 11:50:05.15: [ 7775]: <-- data [1]
Jul 11 11:50:05.35: [ 7775]: MODEM <Timeout>
Jul 11 11:50:05.35: [ 7775]: DELAY 75 ms
Jul 11 11:50:05.43: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:50:07.98: [ 7775]: --> [0:]
Jul 11 11:50:07.98: [ 7775]: TRAINING failed
Jul 11 11:50:07.98: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:08.02: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:08.32: [ 7775]: --> [5:ERROR]
Jul 11 11:50:08.32: [ 7775]: MODEM Command error
Jul 11 11:50:08.32: [ 7775]: FCS error
Jul 11 11:50:08.32: [ 7775]: DELAY 1500 ms
Jul 11 11:50:09.82: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:50:10.14: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:10.14: [ 7775]: <-- data [32]
Jul 11 11:50:10.14: [ 7775]: <-- data [2]
Jul 11 11:50:11.93: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:11.93: [ 7775]: <-- data [23]
Jul 11 11:50:11.93: [ 7775]: <-- data [2]
Jul 11 11:50:12.64: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:12.64: [ 7775]: <-- data [10]
Jul 11 11:50:12.64: [ 7775]: <-- data [2]
Jul 11 11:50:13.25: [ 7775]: --> [2:OK]
Jul 11 11:50:13.25: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:13.39: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:15.18: [ 7775]: --> [2:OK]
Jul 11 11:50:15.18: [ 7775]: REMOTE TSI "660937"
Jul 11 11:50:15.18: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:15.20: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:15.45: [ 7775]: --> [2:OK]
Jul 11 11:50:15.45: [ 7775]: REMOTE wants 4800 bit/s
Jul 11 11:50:15.45: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:50:15.45: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:50:15.45: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:50:15.45: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:50:15.45: [ 7775]: RECV training at v.27ter 4800 bit/s
Jul 11 11:50:15.45: [ 7775]: <-- [10:AT+FRM=48\r]
Jul 11 11:50:19.95: [ 7775]: --> [0:]
Jul 11 11:50:19.95: [ 7775]: MODEM <Empty line>
Jul 11 11:50:19.95: [ 7775]: <-- data [1]
Jul 11 11:50:20.16: [ 7775]: MODEM <Timeout>
Jul 11 11:50:20.16: [ 7775]: DELAY 75 ms
Jul 11 11:50:20.23: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:50:22.78: [ 7775]: --> [0:]
Jul 11 11:50:22.78: [ 7775]: TRAINING failed
Jul 11 11:50:22.78: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:22.82: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:27.82: [ 7775]: <-- data [1]
Jul 11 11:50:27.93: [ 7775]: --> [2:OK]
Jul 11 11:50:27.93: [ 7775]: RECV FAX: Failure to train modems
Jul 11 11:50:27.93: [ 7775]: RECV FAX: end
Jul 11 11:50:27.93: [ 7775]: SESSION END

[/LOG]

And this are my config files:

[config.ttySHSF0]

CountryCode:		34
AreaCode:		922
FAXNumber:		+34.922.111111
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules.europe
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	2
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Organica DTM"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"De %%l|%c|Página %%P de %%T"
MaxRecvPages:		100
ModemType:		Class1		# use this to supply a hint
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT&K0		# setup no flow control
ModemHardFlowCmd:	AT&K3		# setup hardware flow control
ModemSoftFlowCmd:	AT&K4		# setup software flow control
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd:	!Rockwell
ModemModelQueryCmd:	!RC288DPi
ModemRevQueryCmd:	ATI3		# product information
#
ModemDialCmd:		ATDT%s		# T for tone dialing

[/config.ttySHSF0]

[hyla.conf]
#
#	/etc/hylafax/hyla.conf
#
#	System-wide client configuration file


# System-wide configuration information
# -------------------------------------

# Host - host to contact for service
#
Host:			localhost

# Verbose - whether or not to enable protocol tracing
#
Verbose:		No


# Faxstat configuration information
# ---------------------------------

# TimeZone - control whether the times and dates are reported in the
local
#	     timezone of the server (`local') or in GMT (`GMT').
#
TimeZone:		local


# Sendfax configuration information
# ---------------------------------

# DialRules - file containing dialstring rules
#
DialRules: 		"/etc/hylafax/dialrules"

# If you don't want to have cover pages added automatically for every
fax send
# by "sendfax", please uncomment the following line. 

# AutoCoverPage:          No


# FontMap/FontPath added by faxsetup (vie jul  8 16:22:24 WEST 2005)
FontMap:   /usr/share/gs-esp/7.07/lib:/usr/share/gs-esp/fonts:/var/lib/defoma/gs.d/dirs/fonts:/usr/share/cups/fonts:/usr/share/ghostscript/fonts:/usr/local/lib/ghostscript/fonts
FontPath:  /usr/share/gs-esp/7.07/lib:/usr/share/gs-esp/fonts:/var/lib/defoma/gs.d/dirs/fonts:/usr/share/cups/fonts:/usr/share/ghostscript/fonts:/usr/local/lib/ghostscript/fonts

[/hyla.conf]

[hosts.hfaxd] #ricardo is my user account

# hosts.hfaxd
# This file contains permissions and password for every user in
# the system.
#
# For more information on this biject, please see its man page
# and the commands faxadduser and faxdeluser.
^ricardo@localhost::MYENCPASSW:MYENCPASSW
localhost:21::
127.0.0.1

[/host.hfaxd]

I've heard something about user owner of some files... could it be (i
can send fax perfectly, but not receive confirmation email message)

Thanks a lot.

-- 
Ricardo J. Barrios Díaz <ricardobarrios@xxxxxxxxxxxxxxxxxx>
Director del Área de Nuevas Tecnologías
Orgánica Diseño Tecnología y Medio Ambiente


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*