HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: [hylafax-users] Fw: can send but cant receive



check the hylafax config file and edit the max concurrent faxes entry. it
defaults to 1.

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx]On Behalf Of -CDRW-
Sent: Thursday, April 14, 2005 9:20 AM
To: hylafax
Subject: [hylafax-users] Fw: can send but cant receive



 yes i can send trough cypheus or through sendfax to other faxes but when i
 send a fax to the server the reply is blocked by the concurrent and 3 trys
 later the reply is blacklisted by modem. When i execute faxstat -s i can
see
 the fax with blacklisted by modem but when i execute faxstat -r is empty.
 some ideas?

 Yes i have the faxgetty in inittab levels 2345

 thx vitor and sorry my bad english i hope u can understand me.

> ----- Original Message -----
> From: "Vitor Flausino" <vflausino@xxxxxxxxxxxx>
> To: "-CDRW-" <cdrw.fedora@xxxxxxxxx>; <hylafax-users@xxxxxxxxxxx>
> Sent: Thursday, April 14, 2005 12:40 PM
> Subject: Re: [hylafax-users] can send but cant receive
>
>
>> So you can send but can receive? hummm...
>> Does your box answer? In your /etc/inittab, is faxgetty enabled?
>>
>> -vcf
>> -CDRW- wrote:
>>
>>>Hi, i hope us can help me...
>>>
>>>First of all im going to tell my system, im runnig Hylafax 4.2.1 on
>>>Fedora Core 3 with a BestBuy Modem
>>>
>>>My ttyS0 configuration is:
>>>Generic Class 1 modem configuration
>>>CountryCode:            34
>>>AreaCode:               968
>>>FAXNumber:              201
>>>LongDistancePrefix:     0
>>>InternationalPrefix:    00
>>>DialStringRules:        etc/dialrules.europe
>>>ServerTracing:          1
>>>SessionTracing:         0x4f
>>>RecvFileMode:           0644
>>>LogFileMode:            0644
>>>DeviceMode:             0666
>>>RingsBeforeAnswer:      1
>>>SpeakerVolume:          off
>>>GettyArgs:              "-r -b -s %s %1"
>>>LocalIdentifier:        Empresa
>>>TagLineFont:            etc/lutRS18.pcf
>>>TagLineFormat:          "From %%l|%c|Page %%P of %%T"
>>>QualifyTSI:             etc/tsi
>>>MaxRecvPages:           25
>>># Modem-related stuff: should reflect modem command interface
>>># and hardware connection/cabling (e.g. flow control).
>>>ModemType:              Class1          # use this to supply a hint
>>>ModemRate:              19200           # rate for DCE-DTE communication
>>>#ModemFlowControl:      xoff/xon        # XON/XOFF flow control assumed#
>>>#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
>>>#ModemSetupDCDCmd:      AT&C1           # setup so DCD follows carrier
>>>#GettyArgs:             "-h %l dx_%s"   # modem must auto-detect fax/data
>>>
>>>Class1Cmd:              AT+FCLASS=1     # command to enter class 1
>>>Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before
>>>PPM
>>>Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before
>>>TCF
>>>Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before
>>>EOP
>>>Class1MsgRecvHackCmd:   ""      # command to avoid +FCERROR before image
>>>Class1TCFResponseDelay: 75              # 75ms delay between recv TCF &
>>>response
>>>Class1SendMsgDelay:     200             # 75ms delay after training
>>>Class1SwitchingCmd:     AT+FRS=7        # silence between HDLC recv and
>>>trans
>>>Class1TrainingRecovery: 1500            # 1.5sec delay after training
>>>failure
>>>Class1RecvAbortOK:      200             # wait 200ms for abort response
>>>Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC
>>>frames
>>>Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident
>>>frames
>>>Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
>>>Class1TCFMinRun:        1000            # min run is 2/3rds of TCF
>>>duration
>>>
>>>the rest are #
>>>
>>>First times i reply it the faxstat reply was Blocked by concurrent
>>>call, but later of 3 trys the reply was:
>>>
>>>[ 5403]: SESSION BEGIN 000000101 34968202
>>>Apr 14 11:57:53.98: [ 5403]: HylaFAX (tm) Version 4.2.1
>>>Apr 14 11:57:53.98: [ 5403]: SEND FAX: JOB 40 DEST 202 COMMID
>>>000000101 DEVICE '/dev/ttyS0'
>>>Apr 14 11:57:53.98: [ 5403]: MODEM input buffering enabled
>>>Apr 14 11:57:53.98: [ 5403]: <-- [12:AT+FCLASS=1\r]
>>>Apr 14 11:57:54.28: [ 5403]: --> [2:OK]
>>>Apr 14 11:57:54.28: [ 5403]: MODEM set XON/XOFF/FLUSH: input ignored,
>>>output disabled
>>>Apr 14 11:57:54.28: [ 5403]: DIAL 202
>>>Apr 14 11:57:54.28: [ 5403]: <-- [8:ATDT202\r]
>>>Apr 14 11:57:54.59: [ 5403]: --> [11:BLACKLISTED]
>>>Apr 14 11:57:54.59: [ 5403]: SEND FAILED: JOB 40 DEST 202 ERR
>>>Blacklisted by modem
>>>Apr 14 11:57:54.59: [ 5403]: <-- [5:ATH0\r]
>>>Apr 14 11:57:54.88: [ 5403]: --> [2:OK]
>>>Apr 14 11:57:54.88: [ 5403]: MODEM set DTR OFF
>>>Apr 14 11:57:54.88: [ 5403]: SESSION END
>>>
>>>can anyone help me?
>>>thx very much and sorry for my bad english :)
>>>
>>>____________________ HylaFAX(tm) Users Mailing List
>>>_______________________
>>>  To subscribe/unsubscribe, click
>>> http://lists.hylafax.org/cgi-bin/lsg2.cgi
>>> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
>>> /dev/null
>>>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>>>
>>>
>>>
>>>
>>
>>
>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




Project hosted by iFAX Solutions