HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] cant send but i cant receive



Hi, i hope us can help me...

First of all im going to tell my system, im runnig Hylafax 4.2.1 on
Fedora Core 3 with a BestBuy Modem

My ttyS0 configuration is:
Generic Class 1 modem configuration
CountryCode:            34
AreaCode:               968
FAXNumber:              201
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules.europe
ServerTracing:          1
SessionTracing:         0x4f
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-r -b -s %s %1"
LocalIdentifier:        Empresa
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
QualifyTSI:             etc/tsi
MaxRecvPages:           25
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
ModemType:              Class1          # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
#ModemFlowControl:      xoff/xon        # XON/XOFF flow control assumed#
#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
#ModemSetupDCDCmd:      AT&C1           # setup so DCD follows carrier
#GettyArgs:             "-h %l dx_%s"   # modem must auto-detect fax/data

Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before EOP
Class1MsgRecvHackCmd:   ""      # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75              # 75ms delay between recv TCF & response
Class1SendMsgDelay:     200             # 75ms delay after training
Class1SwitchingCmd:     AT+FRS=7        # silence between HDLC recv and trans
Class1TrainingRecovery: 1500            # 1.5sec delay after training failure
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF duration

the rest are #

First times i reply it the faxstat reply was Blocked by concurrent
call, but later of 3 trys the reply was:

[ 5403]: SESSION BEGIN 000000101 34968202
Apr 14 11:57:53.98: [ 5403]: HylaFAX (tm) Version 4.2.1
Apr 14 11:57:53.98: [ 5403]: SEND FAX: JOB 40 DEST 202 COMMID
000000101 DEVICE '/dev/ttyS0'
Apr 14 11:57:53.98: [ 5403]: MODEM input buffering enabled
Apr 14 11:57:53.98: [ 5403]: <-- [12:AT+FCLASS=1\r]
Apr 14 11:57:54.28: [ 5403]: --> [2:OK]
Apr 14 11:57:54.28: [ 5403]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Apr 14 11:57:54.28: [ 5403]: DIAL 202
Apr 14 11:57:54.28: [ 5403]: <-- [8:ATDT202\r]
Apr 14 11:57:54.59: [ 5403]: --> [11:BLACKLISTED]
Apr 14 11:57:54.59: [ 5403]: SEND FAILED: JOB 40 DEST 202 ERR
Blacklisted by modem
Apr 14 11:57:54.59: [ 5403]: <-- [5:ATH0\r]
Apr 14 11:57:54.88: [ 5403]: --> [2:OK]
Apr 14 11:57:54.88: [ 5403]: MODEM set DTR OFF
Apr 14 11:57:54.88: [ 5403]: SESSION END

can anyone help me?
thx very much and sorry for my bad english :)

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




Project hosted by iFAX Solutions