Re: [hylafax-users] how to setup config.tty file for intel 536ep chip modem

[Xun Hu <xunh@xxxxxxxxx>]

Hi, Lee,

 

Thanks for your reply, here are the log and the config file:

 

modem:

intel 536EP chipset

 

config:

------------------------------------------------------------------------------------

#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&K0           # setup no flow control
ModemHardFlowCmd:       AT&K3           # setup hardware flow control
ModemSoftFlowCmd:       AT&K4           # setup software flow control
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
#
#ModemMfrQueryCmd:      !Rockwell
#ModemModelQueryCmd:    !RC288DPi
ModemMfrQueryCmd:       ATI3
ModemModelQueryCmd:     ATI0
ModemRevQueryCmd:       ATI3            # product information
#
ModemDialCmd:           ATDT%s^         # T for tone dialing
#
RecvDataFormat:         adaptive        # only 1-D MR
#Use2DS1                        No
#
#
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before EOP
Class1TCFRespons eDelay: 75              # 75ms delay between recv TCF & response
Class1SendMsgDelay:     75              # 75ms delay after training
Class1SwitchingDelay:   75              # 150ms delay in switching transmission direction
Class1TrainingRecovery: 1500            # 1.5sec delay after training failure
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    100             # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF duration

 

log:

------------------------------------------------------------------------------------

Jan 20 07:47:58.06: [ 1600]: SESSION BEGIN 00001024 14082286077
Jan 20 07:47:58.06: [ 1600]: HylaFAX (tm) Version 4.1.2
Jan 20 07:47:58.06: [ 1600]: SEND FAX: JOB 592 DEST 2286077 COMMID 00001024 DEVICE '/dev/ttyS15'
Jan 20 07:47:58.06: [ 1600]: DELAY 75 ms
Jan 20 07:47:58.14: [ 1600]: DELAY 2600 ms
Jan 20 07:48:01.02: [ 1600]: <-- [4:ATZ\r]
Jan 20 07:48:02.46: [ 1600]: --> [3:ATZ]
Jan 20 07:48:02.46: [ 1600]: --> [2:OK]
Jan 20 07:48:02.46: [ 1600]: DELAY 3000 ms
Jan 20 07:48:05.46: [ 1600]: <-- [5:ATE0\r]
Jan 20 07:48:05.62: [ 1600]: --> [4:ATE0]
Jan 20 07:48:05.62: [ 1600]: --> [2:OK]
Jan 20 07:48:05.62: [ 1600]: <-- [5:ATV1\r]
Jan 20 07:48:05.80: [ 1600]: --> [2:OK]
Jan 20 07:48:05.80: [ 1600]: <-- [5:ATQ0\r]
Jan 20 07:48:05.98: [ 1600]: --> [2:OK]
Jan 20 07:48:05.98: [ 1600]: <-- [7:ATS0=0\r]
Jan 20 07:48:06.16: [ 1600]: --> [2:OK]
Jan 20 07:48:06.16: [ 1600]: <-- [7:ATS8=2\r ]
Jan 20 07:48:06.34: [ 1600]: --> [2:OK]
Jan 20 07:48:06.34: [ 1600]: <-- [8:ATS7=60\r]
Jan 20 07:48:06.52: [ 1600]: --> [2:OK]
Jan 20 07:48:06.52: [ 1600]: <-- [6:AT&K3\r]
Jan 20 07:48:06.70: [ 1600]: --> [2:OK]
Jan 20 07:48:06.70: [ 1600]: <-- [6:AT&D2\r]
Jan 20 07:48:06.88: [ 1600]: --> [2:OK]
Jan 20 07:48:06.88: [ 1600]: <-- [6:AT&C1\r]
Jan 20 07:48:07.06: [ 1600]: --> [2:OK]
Jan 20 07:48:07.06: [ 1600]: <-- [12:AT+FCLASS=1\r]
Jan 20 07:48:07.24: [ 1600]: --> [2:OK]
Jan 20 07:48:07.24: [ 1600]: <-- [7:ATL0M1\r]
Jan 20 07:48:07.42: [ 1600]: --> [2:OK]
Jan 20 07:48:07.42: [ 1600]: <-- [12:AT+FCLASS=1\r]
Jan 20 07:48:07.70: [ 1600]: --> [2:OK]
Jan 20 07:48:07.70: [ 1600]: DIAL 2286077
Jan 20 07:48:07.70: [ 1600]: <-- [13:ATDT2286077^\r]
Jan 20 07:48:18.50: [ 1600]: --> [7:CONNECT]
Jan 20 07:48:20.01: [ 1600]: --> [2:OK]
Jan 20 07:48:20.01: [ 1600]: REMOTE CS I "4082286077"
Jan 20 07:48:20.01: [ 1600]: <-- [9:AT+FRH=3\r]
Jan 20 07:48:20.05: [ 1600]: --> [7:CONNECT]
Jan 20 07:48:20.40: [ 1600]: --> [2:OK]
Jan 20 07:48:20.40: [ 1600]: REMOTE best rate 14400 bit/s
Jan 20 07:48:20.40: [ 1600]: REMOTE max page width 1728 pixels in 215 mm
Jan 20 07:48:20.40: [ 1600]: REMOTE max unlimited page length
Jan 20 07:48:20.40: [ 1600]: REMOTE best vres 7.7 line/mm
Jan 20 07:48:20.40: [ 1600]: REMOTE best format 2-D MR

Jan 20 07:48:20.40: [ 1600]: REMOTE best 0 ms/scanline
Jan 20 07:48:20.40: [ 1600]: USE 14400 bit/s
Jan 20 07:48:20.40: [ 1600]: USE 0 ms/scanline
Jan 20 07:48:20.40: [ 1600]: SEND file "docq/doc622.ps;01"
Jan 20 07:48:20.40: [ 1600]: USE page width 1728 pixels in 215 mm
Jan 20 07:48:20.40: [ 1600]: USE unlimited page length
Jan 20 07:48:20.40: [ 1600]: USE 7.7 line/mm
Jan 20 07:48:20.40: [ 1600]: USE 1-D MR
Jan 20 07:48:20.40: [ 1600]: SEND training at v.17 14400 bit/s
Jan 20 07:48:20.40: [ 1600]: <-- [9:AT+FTH=3\r]
Jan 20 07:48:20.54: [ 1600]: --> [7:CONNECT]
Jan 20 07:48:20.54: [ 1600]: <-- data [23]
Jan 20 07:48:20.54: [ 1600]: <-- data [2]
Jan 20 07:48:22.26: [ 1600]: --> [7:CONNECT]
Jan 20 07:48:22.26: [ 1600]: <-- data [6]
Jan 20 07:48:22.26: [ 1600]: <-- data [2]
Jan 20 07:48:22.54: [ 1600]: --> [2:OK]
Jan 20 07:48:22.54: [ 1600]: <-- [9:AT+FTS=7\r]
Jan 20 07:48:22.64: [ 1600]: --> ; [2:OK]
Jan 20 07:48:22.64: [ 1600]: <-- [11:AT+FTM=145\r]
Jan 20 07:48:22.77: [ 1600]: --> [7:CONNECT]
Jan 20 07:48:22.77: [ 1600]: <-- data [1024]
Jan 20 07:48:22.77: [ 1600]: <-- data [1024]
Jan 20 07:48:22.77: [ 1600]: <-- data [652]
Jan 20 07:48:22.77: [ 1600]: <-- data [2]
Jan 20 07:48:25.89: [ 1600]: --> [4:^S^Q^S^Q]
Jan 20 07:48:25.89: [ 1600]: --> [2:OK]
Jan 20 07:48:25.89: [ 1600]: <-- [9:AT+FRH=3\r]
Jan 20 07:48:26.14: [ 1600]: --> [7:CONNECT]
Jan 20 07:48:27.21: [ 1600]: --> [2:OK]
Jan 20 07:48:27.21: [ 1600]: TRAINING succeeded
Jan 20 07:48:27.21: [ 1600]: DELAY 75 ms
Jan 20 07:48:27.29: [ 1600]: <-- [11:AT+FTM=146\r]
Jan 20 07:48:27.42: [ 1600]: --> [7:CONNECT]
Jan 20 07:48:27.42: [ 1600]: SEND begin page
Jan 20 07:48:27.42: [ 1600]: <-- data [1025]
Jan 20 07:48:27.42: [ 1600]: <-- data [1026]
Jan 20 07:48:27.42: [ 1600]: <-- data [1025]
Jan 20 07:48:27.42 : [ 1600]: <-- data [1025]
Jan 20 07:48:27.42: [ 1600]: <-- data [1029]
Jan 20 07:48:27.42: [ 1600]: <-- data [1024]
Jan 20 07:48:27.42: [ 1600]: <-- data [1025]
Jan 20 07:48:27.42: [ 1600]: <-- data [1024]

Jan 20 07:49:27.42: [ 1600]: MODEM WRITE SHORT: sent 1024, wrote 1013
Jan 20 07:49:27.42: [ 1600]: SENT 107252 bytes of data
Jan 20 07:49:27.42: [ 1600]: SEND end page
Jan 20 07:49:27.42: [ 1600]: <-- [9:AT+FTH=3\r]
Jan 20 07:49:27.42: [ 1600]: --> [4:^S^Q^S^Q]
Jan 20 07:49:27.42: [ 1600]: <-- [5:ATH0\r]
Jan 20 07:49:27.42: [ 1600]: --> [2:OK]
Jan 20 07:49:27.42: [ 1600]: SESSION END

 

 

 

thanks,

 

-xun

Lee Howard <faxguy@xxxxxxxxxxxxxxxx> wrote:

> On 2005.01.17 21:29 Xun Hu wrote:
> > hi, everyone,
> > 
> > i am a new user of hylafax, i have one intel 536ep chip modem, can
> > someone tell me how to config this modem on hylafax environment? i
> > setup my config.ttyS15 file, but somehow it doesn't work well.
>
> Please send a session log or a server log that would illustrate the 
> problem that you're having.
>
> Lee.
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
> To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*