[hylafax-users] Sending problem in hylafax-Help Needed

[biny ks <ksbiny2002@xxxxxxxxxxx>]

Hi,

Sorry my last mail didn't contain enough information.
I am facing problems while sending faxes. The faxes
which I send are receiving there partially.Some middle
lines are missing from each page.

   I am using hylafax-4.1.8-24.2 on suse 9.1. 
   The modem is a class 1 modem.
   Dlink 56k Analog Modem.
   Model No: DFM-560EL
   
  
   The log file which I got when sending fax is as
follows
   
Dec 22 15:10:25.87: [24001]: SESSION BEGIN 00000318
971043538842
Dec 22 15:10:25.87: [24001]: HylaFAX (tm) Version
4.1.8
Dec 22 15:10:25.87: [24001]: SEND FAX: JOB 56 DEST
3538842 COMMID 00000318 DEVICE '/dev/ttyS0'
Dec 22 15:10:25.87: [24001]: MODEM set DTR OFF
Dec 22 15:10:25.87: [24001]: DELAY 75 ms
Dec 22 15:10:25.95: [24001]: MODEM set DTR ON
Dec 22 15:10:25.95: [24001]: DELAY 2600 ms
Dec 22 15:10:29.55: [24001]: MODEM set baud rate:
19200 baud, input flow XON/XOFF, output flow XON/XOFF
Dec 22 15:10:29.55: [24001]: DELAY 10 ms
Dec 22 15:10:29.56: [24001]: MODEM flush i/o
Dec 22 15:10:29.56: [24001]: DELAY 100 ms
Dec 22 15:10:29.66: [24001]: <-- [4:ATZ\r]
Dec 22 15:10:29.83: [24001]: --> [2:OK]
Dec 22 15:10:29.83: [24001]: DELAY 3000 ms
Dec 22 15:10:32.83: [24001]: DELAY 100 ms
Dec 22 15:10:32.93: [24001]: <-- [5:ATE0\r]
Dec 22 15:10:33.03: [24001]: --> [4:ATE0]
Dec 22 15:10:33.03: [24001]: --> [2:OK]
Dec 22 15:10:33.03: [24001]: DELAY 100 ms
Dec 22 15:10:33.13: [24001]: <-- [5:ATV1\r]
Dec 22 15:10:33.24: [24001]: --> [2:OK]
Dec 22 15:10:33.24: [24001]: DELAY 100 ms
Dec 22 15:10:33.34: [24001]: <-- [5:ATQ0\r]
Dec 22 15:10:33.44: [24001]: --> [2:OK]
Dec 22 15:10:33.44: [24001]: DELAY 100 ms
Dec 22 15:10:33.54: [24001]: <-- [7:ATS0=0\r]
Dec 22 15:10:33.64: [24001]: --> [2:OK]
Dec 22 15:10:33.64: [24001]: DELAY 100 ms
Dec 22 15:10:33.74: [24001]: <-- [7:ATS8=2\r]
Dec 22 15:10:33.84: [24001]: --> [2:OK]
Dec 22 15:10:33.84: [24001]: DELAY 100 ms
Dec 22 15:10:33.94: [24001]: <-- [8:ATS7=60\r]
Dec 22 15:10:34.05: [24001]: --> [2:OK]
Dec 22 15:10:34.05: [24001]: DELAY 100 ms
Dec 22 15:10:34.15: [24001]: <-- [12:AT+FCLASS=1\r]
Dec 22 15:10:34.26: [24001]: --> [2:OK]
Dec 22 15:10:34.26: [24001]: DELAY 100 ms
Dec 22 15:10:34.36: [24001]: <-- [7:ATL0M1\r]
Dec 22 15:10:34.46: [24001]: --> [2:OK]
Dec 22 15:10:34.46: [24001]: STATE CHANGE: RUNNING ->
SENDING
Dec 22 15:10:34.46: [24001]: MODEM input buffering
enabled
Dec 22 15:10:34.46: [24001]: Apply DialString rules to
"3538842"
Dec 22 15:10:34.46: [24001]: --> return result
"3538842"
Dec 22 15:10:34.46: [24001]: DELAY 100 ms
Dec 22 15:10:34.56: [24001]: <-- [12:AT+FCLASS=1\r]
Dec 22 15:10:34.77: [24001]: --> [2:OK]
Dec 22 15:10:34.77: [24001]: MODEM set XON/XOFF/FLUSH:
input ignored, output disabled
Dec 22 15:10:34.79: [24001]: DIAL 3538842
Dec 22 15:10:34.79: [24001]: DELAY 100 ms
Dec 22 15:10:34.89: [24001]: <-- [12:ATDT3538842\r]
Dec 22 15:10:54.11: [24001]: --> [7:CONNECT]
Dec 22 15:10:54.11: [24001]: MODEM input buffering
disabled
Dec 22 15:10:55.24: [24001]: --> HDLC<13:FF C0 04 B5
00 6C 05 00 00 00 00 1C 75>
Dec 22 15:10:55.24: [24001]: --> [2:OK]
Dec 22 15:10:55.24: [24001]: REMOTE NSF "AD 00 36 A0
00 00 00 00 38"
Dec 22 15:10:55.24: [24001]: NSF remote fax equipment:
HP 
Dec 22 15:10:55.24: [24001]: DELAY 100 ms
Dec 22 15:10:55.34: [24001]: <-- [9:AT+FRH=3\r]
Dec 22 15:10:55.35: [24001]: --> [7:CONNECT]
Dec 22 15:10:55.95: [24001]: --> HDLC<25:FF C0 02 CC
2C 1C 1C CC AC CC 04 2C 0C 04 04 04 04 04 04 04 04 04
04 9F 6A>
Dec 22 15:10:55.95: [24001]: --> [2:OK]
Dec 22 15:10:55.95: [24001]: REMOTE CSI "04 3538843"
Dec 22 15:10:55.95: [24001]: DELAY 100 ms
Dec 22 15:10:56.05: [24001]: <-- [9:AT+FRH=3\r]
Dec 22 15:10:56.06: [24001]: --> [7:CONNECT]
Dec 22 15:10:56.38: [24001]: --> HDLC<15:FF C8 01 04
77 1F 23 01 49 01 01 19 00 97 91>
Dec 22 15:10:56.40: [24001]: --> [2:OK]
Dec 22 15:10:56.40: [24001]: REMOTE best rate 33600
bit/s
Dec 22 15:10:56.40: [24001]: REMOTE max page width
1728 pixels in 215 mm
Dec 22 15:10:56.40: [24001]: REMOTE max unlimited page
length
Dec 22 15:10:56.40: [24001]: REMOTE best vres 7.7
line/mm
Dec 22 15:10:56.40: [24001]: REMOTE best format 2-D
MMR
Dec 22 15:10:56.40: [24001]: REMOTE supports T.30
Annex A, ECM
Dec 22 15:10:56.40: [24001]: REMOTE best 0 ms/scanline
Dec 22 15:10:56.40: [24001]: USE 14400 bit/s
Dec 22 15:10:56.40: [24001]: USE 0 ms/scanline
Dec 22 15:10:56.40: [24001]: SEND file
"docq/doc58.ps;40"
Dec 22 15:10:56.40: [24001]: USE page width 1728
pixels in 215 mm
Dec 22 15:10:56.40: [24001]: USE unlimited page length
Dec 22 15:10:56.40: [24001]: USE 3.85 line/mm
Dec 22 15:10:56.40: [24001]: USE 2-D MR
Dec 22 15:10:56.40: [24001]: SEND training at v.17
14400 bit/s
Dec 22 15:10:56.40: [24001]: DELAY 100 ms
Dec 22 15:10:56.50: [24001]: <-- [9:AT+FTH=3\r]
Dec 22 15:10:56.55: [24001]: --> [7:CONNECT]
Dec 22 15:10:56.55: [24001]: <-- HDLC<23:FF C0 C2 CE
76 F6 96 2E AE 36 F6 CA 04 0E B6 F6 C6 CE F2 04 04 04
04>
Dec 22 15:10:56.55: [24001]: <-- data [23]
Dec 22 15:10:56.55: [24001]: <-- data [2]
Dec 22 15:10:56.57: [24001]: --> [7:CONNECT]
Dec 22 15:10:56.57: [24001]: <-- HDLC<6:FF C8 C1 00 45
1E>
Dec 22 15:10:56.57: [24001]: <-- data [6]
Dec 22 15:10:56.57: [24001]: <-- data [2]
Dec 22 15:10:58.74: [24001]: --> [2:OK]
Dec 22 15:10:58.74: [24001]: DELAY 100 ms
Dec 22 15:10:58.84: [24001]: <-- [9:AT+FTS=7\r]
Dec 22 15:10:58.85: [24001]: --> [2:OK]
Dec 22 15:10:58.85: [24001]: MODEM set XON/XOFF/FLUSH:
input interpreted, output disabled
Dec 22 15:10:58.85: [24001]: DELAY 100 ms
Dec 22 15:10:58.95: [24001]: <-- [11:AT+FTM=145\r]
Dec 22 15:11:00.63: [24001]: --> [7:CONNECT]
Dec 22 15:11:00.63: [24001]: <-- data [1024]
Dec 22 15:11:01.02: [24001]: <-- data [1024]
Dec 22 15:11:01.42: [24001]: <-- data [652]
Dec 22 15:11:01.82: [24001]: <-- data [2]
Dec 22 15:11:02.18: [24001]: --> [2:OK]
Dec 22 15:11:02.18: [24001]: MODEM set XON/XOFF/DRAIN:
input ignored, output disabled
Dec 22 15:11:02.18: [24001]: DELAY 100 ms
Dec 22 15:11:02.28: [24001]: <-- [9:AT+FRH=3\r]
Dec 22 15:11:02.43: [24001]: --> [7:CONNECT]
Dec 22 15:11:03.55: [24001]: --> HDLC<5:FF C8 21 57
BE>
Dec 22 15:11:03.58: [24001]: --> [2:OK]
Dec 22 15:11:03.58: [24001]: TRAINING succeeded
Dec 22 15:11:03.58: [24001]: DELAY 75 ms
Dec 22 15:11:03.66: [24001]: DELAY 100 ms
Dec 22 15:11:03.76: [24001]: <-- [11:AT+FTM=146\r]
Dec 22 15:11:04.26: [24001]: --> [7:CONNECT]
Dec 22 15:11:04.26: [24001]: SEND begin page
Dec 22 15:11:04.26: [24001]: MODEM set XON/XOFF/FLUSH:
input interpreted, output disabled
Dec 22 15:11:04.26: [24001]: <-- data [1030]
Dec 22 15:11:04.65: [24001]: <-- data [1044]
Dec 22 15:11:05.05: [24001]: <-- data [1053]
Dec 22 15:11:05.45: [24001]: <-- data [1052]
Dec 22 15:11:06.24: [24001]: <-- data [1041]
Dec 22 15:11:06.64: [24001]: <-- data [1028]
Dec 22 15:11:07.04: [24001]: <-- data [1026]
Dec 22 15:11:07.84: [24001]: <-- data [1026]
Dec 22 15:11:08.24: [24001]: <-- data [1032]
Dec 22 15:11:08.64: [24001]: <-- data [1032]
Dec 22 15:11:09.44: [24001]: <-- data [1027]
Dec 22 15:11:09.84: [24001]: <-- data [1033]
Dec 22 15:11:10.24: [24001]: <-- data [1028]
Dec 22 15:11:11.03: [24001]: <-- data [1025]
Dec 22 15:11:11.43: [24001]: <-- data [1027]
Dec 22 15:11:11.83: [24001]: <-- data [1026]
Dec 22 15:11:12.63: [24001]: <-- data [1027]
Dec 22 15:11:13.03: [24001]: <-- data [1029]
Dec 22 15:11:13.43: [24001]: <-- data [1027]
Dec 22 15:11:14.23: [24001]: <-- data [1027]
Dec 22 15:11:14.63: [24001]: <-- data [1036]
Dec 22 15:11:15.03: [24001]: <-- data [1031]
Dec 22 15:11:15.83: [24001]: <-- data [1032]
Dec 22 15:11:16.23: [24001]: <-- data [1034]
Dec 22 15:11:16.62: [24001]: <-- data [1030]
Dec 22 15:11:17.42: [24001]: <-- data [52]
Dec 22 15:11:17.42: [24001]: SENT 25652 bytes of data
Dec 22 15:11:17.42: [24001]: SEND 2D RTC
Dec 22 15:11:17.42: [24001]: <-- data [30]
Dec 22 15:11:17.42: [24001]: <-- data [2]
Dec 22 15:11:17.42: [24001]: SEND end page
Dec 22 15:11:18.81: [24001]: --> [2:OK]
Dec 22 15:11:18.81: [24001]: MODEM set XON/XOFF/DRAIN:
input ignored, output disabled
Dec 22 15:11:18.81: [24001]: DELAY 100 ms
Dec 22 15:11:18.91: [24001]: <-- [9:AT+FTS=9\r]
Dec 22 15:11:18.92: [24001]: --> [2:OK]
Dec 22 15:11:18.92: [24001]: SEND send EOP (no more
pages or documents)
Dec 22 15:11:18.92: [24001]: DELAY 100 ms
Dec 22 15:11:19.02: [24001]: <-- [9:AT+FTH=3\r]
Dec 22 15:11:19.07: [24001]: --> [7:CONNECT]
Dec 22 15:11:19.07: [24001]: <-- HDLC<3:FF C8 F4>
Dec 22 15:11:19.07: [24001]: <-- data [3]
Dec 22 15:11:19.07: [24001]: <-- data [2]
Dec 22 15:11:20.38: [24001]: --> [2:OK]
Dec 22 15:11:20.38: [24001]: DELAY 100 ms
Dec 22 15:11:20.48: [24001]: <-- [9:AT+FRH=3\r]
Dec 22 15:11:20.65: [24001]: --> [7:CONNECT]
Dec 22 15:11:21.74: [24001]: --> HDLC<5:FF C8 31 45
8F>
Dec 22 15:11:21.77: [24001]: --> [2:OK]
Dec 22 15:11:21.77: [24001]: SEND recv MCF (message
confirmation)
Dec 22 15:11:21.77: [24001]: SEND FAX (00000318): FROM
bharat@xxxxxxxxxxxx TO 3538842 (page 1 of 1 sent in
0:25)
Dec 22 15:11:21.77: [24001]: SEND FAX (00000318): FROM
bharat@xxxxxxxxxxxx TO 3538842 (docq/doc58.ps;40 sent
in 0:25)
Dec 22 15:11:21.77: [24001]: DELAY 100 ms
Dec 22 15:11:21.87: [24001]: <-- [9:AT+FTH=3\r]
Dec 22 15:11:21.92: [24001]: --> [7:CONNECT]
Dec 22 15:11:21.92: [24001]: <-- HDLC<3:FF C8 DF>
Dec 22 15:11:21.92: [24001]: <-- data [3]
Dec 22 15:11:21.92: [24001]: <-- data [2]
Dec 22 15:11:23.23: [24001]: --> [2:OK]
Dec 22 15:11:23.23: [24001]: MODEM input buffering
enabled
Dec 22 15:11:23.23: [24001]: DELAY 100 ms
Dec 22 15:11:23.33: [24001]: <-- [5:ATH0\r]
Dec 22 15:11:23.66: [24001]: --> [10:NO CARRIER]
Dec 22 15:11:23.66: [24001]: MODEM No carrier
Dec 22 15:11:23.66: [24001]: MODEM set DTR OFF
Dec 22 15:11:23.66: [24001]: STATE CHANGE: SENDING ->
MODEMWAIT (timeout 5)
Dec 22 15:11:23.66: [24001]: SESSION END

Any help appreciated

thanks
bini

________________________________________________________________________
Yahoo! India Matrimony: Find your life partner online
Go to: http://yahoo.shaadi.com/india-matrimony

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*