[hylafax-users] Failed to properly detect high-speed data carrier

["Sing" <sing@xxxxxxxxxxxxx>]

Hi all,

   I got some problems that I can't recevie some fax on particular sites,
specially when the senter is a HP fax machine. The error message of the
problem is "Failed to properly detect high-speed data carrier". 

The system config is as following :
AMD CPU
Creative Modem Bluster
Gentoo Kernel 2.4
Hylafax-4.2.0
libtiff 3.7.0

Dec 13 17:41:07.69: [ 3306]: HylaFAX (tm) Version 4.2.0
Dec 13 17:41:07.69: [ 3306]: <-- [4:ATA\r]
Dec 13 17:41:15.30: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:15.30: [ 3306]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS1'
Dec 13 17:41:15.30: [ 3306]: RECV FAX: begin
Dec 13 17:41:15.30: [ 3306]: <-- data [32]
Dec 13 17:41:15.30: [ 3306]: <-- data [2]
Dec 13 17:41:17.72: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:17.72: [ 3306]: <-- data [23]
Dec 13 17:41:17.72: [ 3306]: <-- data [2]
Dec 13 17:41:18.66: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:18.66: [ 3306]: <-- data [10]
Dec 13 17:41:18.66: [ 3306]: <-- data [2]
Dec 13 17:41:19.27: [ 3306]: --> [2:OK]
Dec 13 17:41:19.27: [ 3306]: <-- [9:AT+FRH=3\r]
Dec 13 17:41:20.09: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:21.81: [ 3306]: --> [2:OK]
Dec 13 17:41:21.81: [ 3306]: REMOTE TSI "+852 3157 1582"
Dec 13 17:41:21.81: [ 3306]: <-- [9:AT+FRH=3\r]
Dec 13 17:41:21.83: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:22.18: [ 3306]: --> [2:OK]
Dec 13 17:41:22.18: [ 3306]: REMOTE wants 14400 bit/s
Dec 13 17:41:22.18: [ 3306]: REMOTE wants A4 page width (215 mm)
Dec 13 17:41:22.18: [ 3306]: REMOTE wants unlimited page length
Dec 13 17:41:22.18: [ 3306]: REMOTE wants 3.85 line/mm
Dec 13 17:41:22.18: [ 3306]: REMOTE wants 2-D MMR
Dec 13 17:41:22.18: [ 3306]: REMOTE wants T.30 Annex A, 256-byte ECM
Dec 13 17:41:22.18: [ 3306]: RECV training at v.17 14400 bit/s
Dec 13 17:41:22.18: [ 3306]: <-- [11:AT+FRM=145\r]
Dec 13 17:41:24.20: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:25.70: [ 3306]: RECV: TCF 2718 bytes, 79% non-zero, 393 zero-run
Dec 13 17:41:25.70: [ 3306]: RECV: reject TCF (too many non-zero, max 10%)
Dec 13 17:41:25.70: [ 3306]: RECV: reject TCF (zero run too short, min 1800)
Dec 13 17:41:25.71: [ 3306]: --> [10:NO CARRIER]
Dec 13 17:41:25.71: [ 3306]: DELAY 75 ms
Dec 13 17:41:25.79: [ 3306]: <-- [9:AT+FTH=3\r]
Dec 13 17:41:25.81: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:25.81: [ 3306]: <-- data [3]
Dec 13 17:41:25.81: [ 3306]: <-- data [2]
Dec 13 17:41:27.48: [ 3306]: --> [2:OK]
Dec 13 17:41:27.48: [ 3306]: TRAINING failed
Dec 13 17:41:27.48: [ 3306]: <-- [9:AT+FRH=3\r]
Dec 13 17:41:28.31: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:30.02: [ 3306]: --> [2:OK]
Dec 13 17:41:30.02: [ 3306]: REMOTE TSI "+852 3107 1338"
Dec 13 17:41:30.02: [ 3306]: <-- [9:AT+FRH=3\r]
Dec 13 17:41:30.04: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:30.39: [ 3306]: --> [2:OK]
Dec 13 17:41:30.39: [ 3306]: REMOTE wants 12000 bit/s
Dec 13 17:41:30.39: [ 3306]: REMOTE wants A4 page width (215 mm)
Dec 13 17:41:30.39: [ 3306]: REMOTE wants unlimited page length
Dec 13 17:41:30.39: [ 3306]: REMOTE wants 3.85 line/mm
Dec 13 17:41:30.39: [ 3306]: REMOTE wants 2-D MMR
Dec 13 17:41:30.39: [ 3306]: REMOTE wants T.30 Annex A, 256-byte ECM
Dec 13 17:41:30.39: [ 3306]: RECV training at v.17 12000 bit/s
Dec 13 17:41:30.39: [ 3306]: <-- [11:AT+FRM=121\r]
Dec 13 17:41:32.41: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:33.92: [ 3306]: RECV: TCF 2266 bytes, 96% non-zero, 38 zero-run
Dec 13 17:41:33.92: [ 3306]: RECV: reject TCF (too many non-zero, max 10%)
Dec 13 17:41:33.92: [ 3306]: RECV: reject TCF (zero run too short, min 1500)
Dec 13 17:41:33.93: [ 3306]: --> [10:NO CARRIER]
Dec 13 17:41:33.93: [ 3306]: DELAY 75 ms
Dec 13 17:41:34.01: [ 3306]: <-- [9:AT+FTH=3\r]
Dec 13 17:41:34.03: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:34.03: [ 3306]: <-- data [3]
Dec 13 17:41:34.03: [ 3306]: <-- data [2]
Dec 13 17:41:35.70: [ 3306]: --> [2:OK]
Dec 13 17:41:35.70: [ 3306]: TRAINING failed
Dec 13 17:41:35.70: [ 3306]: <-- [9:AT+FRH=3\r]
Dec 13 17:41:36.53: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:38.24: [ 3306]: --> [2:OK]
Dec 13 17:41:38.24: [ 3306]: REMOTE TSI "+852 3107 1338"
Dec 13 17:41:38.24: [ 3306]: <-- [9:AT+FRH=3\r]
Dec 13 17:41:38.26: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:38.61: [ 3306]: --> [2:OK]
Dec 13 17:41:38.61: [ 3306]: REMOTE wants 9600 bit/s
Dec 13 17:41:38.61: [ 3306]: REMOTE wants A4 page width (215 mm)
Dec 13 17:41:38.61: [ 3306]: REMOTE wants unlimited page length
Dec 13 17:41:38.61: [ 3306]: REMOTE wants 3.85 line/mm
Dec 13 17:41:38.61: [ 3306]: REMOTE wants 2-D MMR
Dec 13 17:41:38.61: [ 3306]: REMOTE wants T.30 Annex A, 256-byte ECM
Dec 13 17:41:38.61: [ 3306]: RECV training at v.17 9600 bit/s
Dec 13 17:41:38.61: [ 3306]: <-- [10:AT+FRM=97\r]
Dec 13 17:41:40.63: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:42.14: [ 3306]: RECV: TCF 1814 bytes, 1% non-zero, 1778 zero-run
Dec 13 17:41:42.15: [ 3306]: --> [10:NO CARRIER]
Dec 13 17:41:42.15: [ 3306]: DELAY 75 ms
Dec 13 17:41:42.23: [ 3306]: TRAINING succeeded
Dec 13 17:41:42.23: [ 3306]: <-- [9:AT+FTH=3\r]
Dec 13 17:41:42.25: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:42.25: [ 3306]: <-- data [3]
Dec 13 17:41:42.25: [ 3306]: <-- data [2]
Dec 13 17:41:43.92: [ 3306]: --> [2:OK]
Dec 13 17:41:43.92: [ 3306]: <-- [10:AT+FRM=98\r]
Dec 13 17:41:50.92: [ 3306]: <-- data [1]
Dec 13 17:41:51.03: [ 3306]: --> [2:^P^C]
Dec 13 17:41:51.03: [ 3306]: --> [2:OK]
Dec 13 17:41:51.03: [ 3306]: RECV FAX (000000196): from +852 3157 1582, page 1
in 0:09, INF, 3.85 line/mm, 2-D MMR, 9600 bit/s
Dec 13 17:41:51.03: [ 3306]: RECV FAX (000000196): recvq/fax000000137.tif from
+852 3107 1338, route to <unspecified>, 1 pages in 0:36
Dec 13 17:41:51.03: [ 3306]: RECV FAX: Failed to properly detect high-speed
data carrier.
Dec 13 17:41:51.03: [ 3306]: <-- [9:AT+FTH=3\r]
Dec 13 17:41:51.05: [ 3306]: --> [7:CONNECT]
Dec 13 17:41:51.05: [ 3306]: <-- data [3]
Dec 13 17:41:51.05: [ 3306]: <-- data [2]
Dec 13 17:41:52.72: [ 3306]: --> [2:OK]
Dec 13 17:41:52.72: [ 3306]: RECV FAX (000000196): session with +852 3157 1582
terminated abnormally: Failed to properly detect high-speed data carrier.
Dec 13 17:41:52.72: [ 3306]: RECV FAX: bin/faxrcvd "recvq/fax000000137.tif"
"ttyS1" "000000196" "Failed to properly detect high-speed data carrier." "" ""
Dec 13 17:41:52.72: [ 3306]: RECV FAX: end
Dec 13 17:41:52.72: [ 3306]: SESSION END

Yours
 
   Sing

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*