[hylafax-users] Errore no answer T.30 T1 Timeout

[Pilia Massimo <PILIA@xxxxxxxxxxx>]

Non riesco a mandare i fax con il modem MultiTech 2834ZDX, forse sbaglio
qualcosa sulla configurazione.

Se qualcuno ha qualche idea ringrazio anticipatamente.


Massimo

email: pilia@xxxxxxxxxxx

File: config.ttyS1:

# $Id: mt-1432,v 1.2 2002/04/07 20:29:26 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Multi-Tech MT1432, MT224BA, and MT1932ZDX modems.
#
# MT1432	firmware rev 0307 I or newer
# MT132BG	rev 0109A
# MT1932ZDX	rev 0109H
#
# Note that MT1432 modems come in several varieties:
#
# MT1432BA	uses Rockwell data pump
# MT1432BA/A	uses AT&T data pump
# MT1432BG	MT1432BA tweaked for German FCC
# MT1432MK	(for UK?)
#
# The modem has been tried with both XON/XOFF and RTS/CTS flow
# control; this configuration is for hardware flow control.
#
#
CountryCode:		39
AreaCode:		075
FAXNumber:		+39.075.8009203
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0664
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		on
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Nome Ditta"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		19200		# lock rate for DCE-DTE
communication
ModemFlowControl:	rtscts		# default
#
ModemHardFlowCmd:	AT&E4		# hardware flow control
ModemSoftFlowCmd:	AT&E5		# software flow control
ModemSetupDTRCmd:	AT&D3		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or
not)
ModemSetupAACmd:	AT+FAA=1	# enable adaptive-answer in class 2
#
# NB: some models get confused by @ in ModemDialCmd
#
ModemDialCmd:		ATDT0%s
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start
recv


File di log dell' errore:

Dec 02 08:42:59.40: [ 1949]: SESSION BEGIN 00000004 39
Dec 02 08:42:59.40: [ 1949]: HylaFAX (tm) Version 4.1.5
Dec 02 08:42:59.40: [ 1949]: SEND FAX: JOB 2 DEST 1 COMMID 00000004 DEVICE
'/dev/ttyS1'
Dec 02 08:42:59.40: [ 1949]: DELAY 75 ms
Dec 02 08:42:59.48: [ 1949]: DELAY 2600 ms
Dec 02 08:43:02.08: [ 1949]: DELAY 10 ms
Dec 02 08:43:02.09: [ 1949]: <-- [4:ATZ\r]
Dec 02 08:43:02.70: [ 1949]: --> [3:ATZ]
Dec 02 08:43:02.70: [ 1949]: --> [2:OK]
Dec 02 08:43:02.70: [ 1949]: DELAY 3000 ms
Dec 02 08:43:05.70: [ 1949]: <-- [5:ATE0\r]
Dec 02 08:43:05.91: [ 1949]: --> [4:ATE0]
Dec 02 08:43:05.91: [ 1949]: --> [2:OK]
Dec 02 08:43:05.91: [ 1949]: <-- [5:ATV1\r]
Dec 02 08:43:06.12: [ 1949]: --> [2:OK]
Dec 02 08:43:06.12: [ 1949]: <-- [5:ATQ0\r]
Dec 02 08:43:06.33: [ 1949]: --> [2:OK]
Dec 02 08:43:06.33: [ 1949]: <-- [7:ATS0=0\r]
Dec 02 08:43:06.55: [ 1949]: --> [2:OK]
Dec 02 08:43:06.55: [ 1949]: <-- [7:ATS8=2\r]
Dec 02 08:43:06.77: [ 1949]: --> [2:OK]
Dec 02 08:43:06.77: [ 1949]: <-- [8:ATS7=60\r]
Dec 02 08:43:06.99: [ 1949]: --> [2:OK]
Dec 02 08:43:06.99: [ 1949]: <-- [6:AT&E4\r]
Dec 02 08:43:07.21: [ 1949]: --> [2:OK]
Dec 02 08:43:07.21: [ 1949]: <-- [6:AT&D3\r]
Dec 02 08:43:07.43: [ 1949]: --> [2:OK]
Dec 02 08:43:07.43: [ 1949]: <-- [6:AT&C1\r]
Dec 02 08:43:07.65: [ 1949]: --> [2:OK]
Dec 02 08:43:07.65: [ 1949]: <-- [12:AT+FCLASS=2\r]
Dec 02 08:43:07.87: [ 1949]: --> [2:OK]
Dec 02 08:43:07.87: [ 1949]: <-- [10:AT+FTBC=0\r]
Dec 02 08:43:08.09: [ 1949]: --> [2:OK]
Dec 02 08:43:08.09: [ 1949]: <-- [10:AT+FBOR=0\r]
Dec 02 08:43:08.31: [ 1949]: --> [2:OK]
Dec 02 08:43:08.31: [ 1949]: <-- [13:AT+FPHCTO=30\r]
Dec 02 08:43:08.53: [ 1949]: --> [2:OK]
Dec 02 08:43:08.53: [ 1949]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Dec 02 08:43:08.76: [ 1949]: --> [2:OK]
Dec 02 08:43:08.76: [ 1949]: <-- [7:ATL0M1\r]
Dec 02 08:43:08.98: [ 1949]: --> [2:OK]
Dec 02 08:43:08.98: [ 1949]: <-- [12:AT+FCLASS=2\r]
Dec 02 08:43:09.30: [ 1949]: --> [2:OK]
Dec 02 08:43:09.30: [ 1949]: <-- [10:AT+FTBC=0\r]
Dec 02 08:43:09.62: [ 1949]: --> [2:OK]
Dec 02 08:43:09.62: [ 1949]: <-- [10:AT+FBOR=0\r]
Dec 02 08:43:09.94: [ 1949]: --> [2:OK]
Dec 02 08:43:09.94: [ 1949]: <-- [13:AT+FPHCTO=30\r]
Dec 02 08:43:10.26: [ 1949]: --> [2:OK]
Dec 02 08:43:10.26: [ 1949]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Dec 02 08:43:10.59: [ 1949]: --> [2:OK]
Dec 02 08:43:10.59: [ 1949]: <-- [27:AT+FLID="Petrini 1822 SpA"\r]
Dec 02 08:43:10.92: [ 1949]: --> [2:OK]
Dec 02 08:43:10.92: [ 1949]: DIAL 1
Dec 02 08:43:10.92: [ 1949]: <-- [7:ATDT01\r]
Dec 02 08:44:54.11: [ 1949]: --> [8:+FHNG:11]
Dec 02 08:44:54.11: [ 1949]: REMOTE HANGUP: No answer (T.30 T1 timeout)
(code 11)
Dec 02 08:44:54.11: [ 1949]: SEND FAILED: JOB 2 DEST 1 ERR No answer (T.30
T1 timeout)
Dec 02 08:44:54.11: [ 1949]: SEND FAILED: JOB 2 DEST 1 ERR No answer (T.30
T1 timeout); too many attempts to dial
Dec 02 08:44:54.11: [ 1949]: <-- [5:ATH0\r]
Dec 02 08:44:54.78: [ 1949]: --> [2:OK]
Dec 02 08:44:54.78: [ 1949]: SESSION END






____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*