[hylafax-users] error: T.30 T2 timeout, expected signal not received (4h faxmessage)

[dom <lists@xxxxxxxxxx>]

Hi together
had this week a wonderfull fax: one page in 4:41:38 hours!!

(T.30 T2 timeout, expected signal not received)

first: whats the matter of this error?
second: is there a possibility to set a maximum of modem-time (e.g. 20min)

here the logfile of the fax and at the end the modem-config..

thanks for every help
dom

logfile:
Nov 23 08:22:18.70: [ 2473]: SESSION BEGIN 000000320 4117422179
Nov 23 08:22:18.70: [ 2473]: HylaFAX (tm) Version 4.2.0
Nov 23 08:22:18.70: [ 2473]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Nov 23 08:22:18.70: [ 2473]: <-- [4:ATA\r]
Nov 23 08:22:21.71: [ 2473]: --> [7:CONNECT]
Nov 23 08:22:21.71: [ 2473]: ANSWER: FAX CONNECTION  DEVICE '/dev/modem'
Nov 23 08:22:21.71: [ 2473]: STATE CHANGE: ANSWERING -> RECEIVING
Nov 23 08:22:21.71: [ 2473]: MODEM input buffering enabled
Nov 23 08:22:21.71: [ 2473]: RECV FAX: begin
Nov 23 08:22:21.74: [ 2473]: MODEM input buffering disabled
Nov 23 08:22:21.74: [ 2473]: <-- HDLC<32:FF C0 04 AD 00 55 12 9E 36 86 62
82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 4C 74 0C>
Nov 23 08:22:21.74: [ 2473]: <-- data [32]
Nov 23 08:22:21.74: [ 2473]: <-- data [2]
Nov 23 08:22:23.59: [ 2473]: --> [7:CONNECT]
Nov 23 08:22:23.59: [ 2473]: <-- HDLC<23:FF C0 02 04 26 76 86 16 AE A6 4E
2A 04 5E 76 86 76 96 62 04 D2 2A 62>
Nov 23 08:22:23.59: [ 2473]: <-- data [23]
Nov 23 08:22:23.59: [ 2473]: <-- data [2]
Nov 23 08:22:24.34: [ 2473]: --> [7:CONNECT]
Nov 23 08:22:24.34: [ 2473]: <-- HDLC<10:FF C8 01 00 76 5F 23 01 FB C0>
Nov 23 08:22:24.34: [ 2473]: <-- data [10]
Nov 23 08:22:24.34: [ 2473]: <-- data [2]
Nov 23 08:22:24.76: [ 2473]: --> [2:OK]
Nov 23 08:22:24.76: [ 2473]: <-- [9:AT+FRH=3\r]
Nov 23 08:22:24.83: [ 2473]: --> [7:CONNECT]
Nov 23 08:22:26.58: [ 2473]: --> HDLC<25:FF C0 C2 0C 2C CC 2C EC 4C EC 8C
0C 04 04 04 04 04 04 04 04 04 04 04 E3 1A>
Nov 23 08:22:26.59: [ 2473]: --> [2:OK]
Nov 23 08:22:26.59: [ 2473]: REMOTE TSI "017274340"
Nov 23 08:22:26.59: [ 2473]: <-- [9:AT+FRH=3\r]
Nov 23 08:22:26.62: [ 2473]: --> [7:CONNECT]
Nov 23 08:22:26.93: [ 2473]: --> HDLC<12:FF C8 C1 00 44 1F 23 01 01 00 53
55>
Nov 23 08:22:26.94: [ 2473]: --> [2:OK]
Nov 23 08:22:26.94: [ 2473]: REMOTE wants 14400 bit/s
Nov 23 08:22:26.94: [ 2473]: REMOTE wants A4 page width (215 mm)
Nov 23 08:22:26.94: [ 2473]: REMOTE wants unlimited page length
Nov 23 08:22:26.94: [ 2473]: REMOTE wants 3.85 line/mm
Nov 23 08:22:26.94: [ 2473]: REMOTE wants 2-D MMR
Nov 23 08:22:26.94: [ 2473]: REMOTE wants T.30 Annex A, 256-byte ECM
Nov 23 08:22:26.94: [ 2473]: RECV training at v.17 14400 bit/s
Nov 23 08:22:26.94: [ 2473]: MODEM set XON/XOFF/DRAIN: input ignored,
output generated
Nov 23 08:22:26.94: [ 2473]: <-- [11:AT+FRM=145\r]
Nov 23 08:22:28.71: [ 2473]: --> [7:CONNECT]
Nov 23 08:22:30.23: [ 2473]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Nov 23 08:22:30.23: [ 2473]: RECV: TCF 2720 bytes, 0% non-zero, 2702
zero-run
Nov 23 08:22:30.24: [ 2473]: --> [10:NO CARRIER]
Nov 23 08:22:30.24: [ 2473]: DELAY 75 ms
Nov 23 08:22:30.31: [ 2473]: TRAINING succeeded
Nov 23 08:22:30.31: [ 2473]: <-- [9:AT+FTH=3\r]
Nov 23 08:22:30.35: [ 2473]: --> [7:CONNECT]
Nov 23 08:22:30.35: [ 2473]: <-- HDLC<3:FF C8 21>
Nov 23 08:22:30.35: [ 2473]: <-- data [3]
Nov 23 08:22:30.35: [ 2473]: <-- data [2]
Nov 23 08:22:31.56: [ 2473]: --> [2:OK]
Nov 23 08:22:31.56: [ 2473]: MODEM input buffering enabled
Nov 23 08:22:31.56: [ 2473]: MODEM set XON/XOFF/FLUSH: input ignored,
output generated
Nov 23 08:22:31.56: [ 2473]: <-- [11:AT+FRM=146\r]
Nov 23 08:22:32.48: [ 2473]: --> [7:CONNECT]

[SNIP DATABLOCKS]

Nov 23 08:23:10.41: [ 2473]: RECV received frame number 251
Nov 23 08:23:10.41: [ 2473]: RECV frame FCS check failed
[AFTER 4:40 HOURS!!!! - nothing snipt here!!!]
Nov 23 13:03:39.60: [ 2473]: Timeout receiving HDLC frame
Nov 23 13:03:43.20: [ 2473]: Timeout awaiting synchronization sequence
Nov 23 13:03:45.70: [ 2473]: MODEM TIMEOUT: waiting for DLE+ETX
Nov 23 13:03:47.70: [ 2473]: MODEM TIMEOUT: reading line from modem
Nov 23 13:03:47.70: [ 2473]: MODEM <Empty line>
Nov 23 13:03:49.71: [ 2473]: MODEM TIMEOUT: reading line from modem
Nov 23 13:03:49.71: [ 2473]: MODEM <Empty line>
Nov 23 13:03:51.71: [ 2473]: MODEM TIMEOUT: reading line from modem
Nov 23 13:03:51.71: [ 2473]: MODEM <Empty line>
Nov 23 13:03:51.71: [ 2473]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Nov 23 13:03:51.71: [ 2473]: MODEM input buffering disabled
Nov 23 13:03:51.71: [ 2473]: <-- [9:AT+FRH=3\r]
Nov 23 13:03:58.71: [ 2473]: --> [0:]
Nov 23 13:03:58.71: [ 2473]: MODEM <Empty line>
Nov 23 13:03:58.71: [ 2473]: MODEM TIMEOUT: waiting for v.21 carrier
Nov 23 13:03:58.71: [ 2473]: <-- data [1]
Nov 23 13:03:59.11: [ 2473]: MODEM TIMEOUT: reading line from modem
Nov 23 13:03:59.11: [ 2473]: MODEM <Timeout>
Nov 23 13:03:59.11: [ 2473]: RECV keeping unconfirmed page
Nov 23 13:03:59.11: [ 2473]: RECV/CQ: Adjusting for EOFB at row 75
Nov 23 13:03:59.22: [ 2473]: RECV: 64512 bytes of data, 75 total lines
Nov 23 13:03:59.22: [ 2473]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Nov 23 13:03:59.22: [ 2473]: MODEM input buffering disabled
Nov 23 13:03:59.22: [ 2473]: RECV FAX (000000320): from 017274340, page 1
in 4:41:29, INF, 3.85 line/mm, 2-D MMR, 14400 bit/s
Nov 23 13:03:59.22: [ 2473]: RECV FAX (000000320): recvq/fax000000242.tif
from 017274340, route to <unspecified>, 1 pages in 4:41:38
Nov 23 13:03:59.24: [ 2473]: RECV FAX: T.30 T2 timeout, expected signal
not received
Nov 23 13:03:59.24: [ 2473]: <-- [9:AT+FTH=3\r]
Nov 23 13:04:01.79: [ 2473]: --> [0:]
Nov 23 13:04:01.79: [ 2473]: MODEM TIMEOUT: sending HDLC frame
Nov 23 13:04:01.79: [ 2473]: MODEM input buffering enabled
Nov 23 13:04:01.79: [ 2473]: RECV FAX (000000320): session with 017274340
terminated abnormally: T.30 T2 timeout, expected signal not received
Nov 23 13:04:01.79: [ 2473]: RECV FAX: bin/faxrcvd
"recvq/fax000000242.tif" "modem" "000000320" "T.30 T2 timeout,
expected signal not received" "" ""
Nov 23 13:04:01.80: [ 2473]: RECV FAX: end
Nov 23 13:04:01.80: [ 2473]: SESSION END


config.modem:
CountryCode:            41
AreaCode:               1
FAXNumber:              [SNIP]
LongDistancePrefix:     0
InternationalPrefix:    0
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         0xFFF #1
RecvFileMode:           0666
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      2
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "[SNIP]"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
ModemType:              Class1          # use this to supply a hint
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before
PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before
TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before
EOP
Class1MsgRecvHackCmd:   ""      # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75              # 75ms delay between recv TCF &
response
Class1SendMsgDelay:     200             # 75ms delay after training
Class1SwitchingCmd:     AT+FRS=1        # silence between HDLC recv and
trans
Class1TrainingRecovery: 1500            # 1.5sec delay after training
failure
Class1RecvAbortOK:      400
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident
frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF
duration

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*