[hylafax-users] Failure to train remote modem !?

["K.Balázs" <mukfuk@xxxxxxxxxxx>]

Hi list!

I !sometimes! get the following error: Failure to train remote modem

 

The log:

Nov 17 11:19:11.94: [ 4551]: SESSION BEGIN 000002628 **********

Nov 17 11:19:11.94: [ 4551]: HylaFAX (tm) Version 4.2.0

Nov 17 11:19:11.94: [ 4551]: SEND FAX: JOB 329 DEST ********** COMMID 000002628 DEVICE '/dev/ttyS0'

Nov 17 11:19:11.94: [ 4551]: sched policy=1, priority=1

Nov 17 11:19:11.94: [ 4551]: <-- [12:AT+FCLASS=1\r]

Nov 17 11:19:12.07: [ 4551]: --> [2:OK]

Nov 17 11:19:12.07: [ 4551]: DIAL **********

Nov 17 11:19:12.07: [ 4551]: <-- [15:ATDT********\r]

Nov 17 11:19:25.11: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:26.48: [ 4551]: --> [2:OK]

Nov 17 11:19:26.48: [ 4551]: REMOTE CSI "******"

Nov 17 11:19:26.49: [ 4551]: <-- [9:AT+FRH=3\r]

Nov 17 11:19:26.52: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:26.83: [ 4551]: --> [2:OK]

Nov 17 11:19:26.83: [ 4551]: REMOTE best rate 4800 bit/s

Nov 17 11:19:26.83: [ 4551]: REMOTE max A4 page width (215 mm)

Nov 17 11:19:26.83: [ 4551]: REMOTE max A4 page length (297 mm)

Nov 17 11:19:26.83: [ 4551]: REMOTE best vres 7.7 line/mm

Nov 17 11:19:26.83: [ 4551]: REMOTE best format 1-D MH

Nov 17 11:19:26.83: [ 4551]: REMOTE best 0 ms/scanline

Nov 17 11:19:26.83: [ 4551]: USE 4800 bit/s

Nov 17 11:19:26.83: [ 4551]: USE 0 ms/scanline

Nov 17 11:19:26.83: [ 4551]: SEND file "docq/doc329.cover;01"

Nov 17 11:19:26.83: [ 4551]: USE A4 page width (215 mm)

Nov 17 11:19:26.83: [ 4551]: USE A4 page length (297 mm)

Nov 17 11:19:26.83: [ 4551]: USE 7.7 line/mm

Nov 17 11:19:26.83: [ 4551]: USE 1-D MH

Nov 17 11:19:26.83: [ 4551]: SEND training at v.27ter 4800 bit/s

Nov 17 11:19:26.83: [ 4551]: <-- [9:AT+FTH=3\r]

Nov 17 11:19:27.87: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:27.87: [ 4551]: <-- data [23]

Nov 17 11:19:27.87: [ 4551]: <-- data [2]

Nov 17 11:19:28.89: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:28.89: [ 4551]: <-- data [6]

Nov 17 11:19:28.89: [ 4551]: <-- data [2]

Nov 17 11:19:29.19: [ 4551]: --> [2:OK]

Nov 17 11:19:29.19: [ 4551]: DELAY 70 ms

Nov 17 11:19:29.26: [ 4551]: <-- [10:AT+FTM=48\r]

Nov 17 11:19:30.28: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:30.28: [ 4551]: <-- data [900]

Nov 17 11:19:30.28: [ 4551]: <-- data [2]

Nov 17 11:19:31.84: [ 4551]: --> [2:]

Nov 17 11:19:31.84: [ 4551]: Problem sending TCF data

Nov 17 11:19:31.84: [ 4551]: <-- [9:AT+FRH=3\r]

Nov 17 11:19:31.84: [ 4551]: --> [2:OK]

Nov 17 11:19:31.84: [ 4551]: DELAY 1500 ms

Nov 17 11:19:33.34: [ 4551]: SEND training at v.27ter fallback mode 2400 bit/s

Nov 17 11:19:33.34: [ 4551]: <-- [9:AT+FTH=3\r]

Nov 17 11:19:33.34: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:33.34: [ 4551]: <-- data [23]

Nov 17 11:19:33.34: [ 4551]: <-- data [2]

Nov 17 11:19:33.34: [ 4551]: --> [5:˙„

---

]

Nov 17 11:19:33.34: [ 4551]: Error sending T.30 prologue frames

Nov 17 11:19:33.34: [ 4551]: TRAINING failed

Nov 17 11:19:33.34: [ 4551]: SEND: Failure to train remote modem at 2400 bps or minimum speed; Giving up after 3 attempts to send same page "docq/doc329.cover;01", dirnum 0

Nov 17 11:19:33.34: [ 4551]: <-- [9:AT+FTH=3\r]

Nov 17 11:19:33.34: [ 4551]: --> [2:OK]

Nov 17 11:19:33.34: [ 4551]: <-- [5:ATH0\r]

Nov 17 11:19:34.48: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:35.47: [ 4551]: --> [7:CONNECT]

Nov 17 11:19:40.47: [ 4551]: MODEM <Timeout>

Nov 17 11:19:40.48: [ 4551]: sched policy=0, priority=0

Nov 17 11:19:40.48: [ 4551]: SESSION END

 

My config:

Class1, 19200, rtscts, Zyxel OMNI extended modem, WHFC client program

 

What’s the problem ?

I saw  the archive mails, but I didn’t find anything.

Anybody help me ??

Thx in advance.

 

Balázs