[hylafax-users] check modem power

[Tóth László <tczeszter@xxxxxxxxxx>]

Hi!

 

I use Suse 9.1 with hylafaxserver, i can receive fax but i cant send. Always get this error:

 

Nov 12 21:38:51.84: [ 2475]: SESSION BEGIN 00000035 36942
Nov 12 21:38:51.84: [ 2475]: HylaFAX (tm) Version 4.1.8
Nov 12 21:38:51.84: [ 2475]: SEND FAX: JOB 6 DEST 2 COMMID 00000035 DEVICE '/dev/ttyS14'
Nov 12 21:38:51.84: [ 2475]: MODEM set DTR OFF
Nov 12 21:38:51.84: [ 2475]: DELAY 75 ms
Nov 12 21:38:51.92: [ 2475]: MODEM set DTR ON
Nov 12 21:38:51.92: [ 2475]: DELAY 2600 ms
Nov 12 21:38:55.52: [ 2475]: MODEM set baud rate: 9600 baud, input flow XON/XOFF, output flow XON/XOFF
Nov 12 21:38:55.52: [ 2475]: DELAY 10 ms
Nov 12 21:38:55.53: [ 2475]: MODEM flush i/o
Nov 12 21:38:55.53: [ 2475]: <-- [4:ATZ\r]
Nov 12 21:38:55.98: [ 2475]: --> [2:OK]
Nov 12 21:38:55.98: [ 2475]: DELAY 3000 ms
Nov 12 21:38:58.98: [ 2475]: <-- [5:ATE0\r]
Nov 12 21:38:58.99: [ 2475]: --> [4:ATE0]
Nov 12 21:38:59.00: [ 2475]: --> [2:OK]
Nov 12 21:38:59.00: [ 2475]: <-- [5:ATV1\r]
Nov 12 21:38:59.02: [ 2475]: --> [2:OK]
Nov 12 21:38:59.02: [ 2475]: <-- [5:ATQ0\r]
Nov 12 21:38:59.04: [ 2475]: --> [2:OK]
Nov 12 21:38:59.04: [ 2475]: <-- [7:ATS0=0\r]
Nov 12 21:38:59.06: [ 2475]: --> [2:OK]
Nov 12 21:38:59.06: [ 2475]: <-- [7:ATS8=2\r]
Nov 12 21:38:59.08: [ 2475]: --> [2:OK]
Nov 12 21:38:59.08: [ 2475]: <-- [8:ATS7=60\r]
Nov 12 21:38:59.10: [ 2475]: --> [2:OK]
Nov 12 21:38:59.10: [ 2475]: <-- [12:AT+FCLASS=2\r]
Nov 12 21:38:59.12: [ 2475]: --> [2:OK]
Nov 12 21:38:59.12: [ 2475]: <-- [10:AT+FTBC=0\r]
Nov 12 21:38:59.14: [ 2475]: --> [2:OK]
Nov 12 21:38:59.14: [ 2475]: <-- [10:AT+FBOR=0\r]
Nov 12 21:38:59.17: [ 2475]: --> [2:OK]
Nov 12 21:38:59.17: [ 2475]: <-- [13:AT+FPHCTO=30\r]
Nov 12 21:38:59.19: [ 2475]: --> [2:OK]
Nov 12 21:38:59.19: [ 2475]: <-- [10:AT+FBUG=1\r]
Nov 12 21:38:59.22: [ 2475]: --> [2:OK]
Nov 12 21:38:59.22: [ 2475]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Nov 12 21:38:59.26: [ 2475]: --> [2:OK]
Nov 12 21:38:59.26: [ 2475]: <-- [7:ATL1M1\r]
Nov 12 21:38:59.28: [ 2475]: --> [2:OK]
Nov 12 21:38:59.28: [ 2475]: STATE CHANGE: RUNNING -> SENDING
Nov 12 21:38:59.28: [ 2475]: MODEM input buffering enabled
Nov 12 21:38:59.28: [ 2475]: Apply DialString rules to "2"
Nov 12 21:38:59.28: [ 2475]: --> return result "2"
Nov 12 21:38:59.28: [ 2475]: <-- [12:AT+FCLASS=2\r]
Nov 12 21:38:59.40: [ 2475]: --> [2:OK]
Nov 12 21:38:59.40: [ 2475]: <-- [10:AT+FTBC=0\r]
Nov 12 21:38:59.52: [ 2475]: --> [2:OK]
Nov 12 21:38:59.52: [ 2475]: <-- [10:AT+FBOR=0\r]
Nov 12 21:38:59.65: [ 2475]: --> [2:OK]
Nov 12 21:38:59.65: [ 2475]: <-- [13:AT+FPHCTO=30\r]
Nov 12 21:38:59.77: [ 2475]: --> [2:OK]
Nov 12 21:38:59.77: [ 2475]: <-- [10:AT+FBUG=1\r]
Nov 12 21:38:59.90: [ 2475]: --> [2:OK]
Nov 12 21:38:59.90: [ 2475]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Nov 12 21:39:00.04: [ 2475]: --> [2:OK]
Nov 12 21:39:00.04: [ 2475]: <-- [23:AT+FLID="NothingSetup"\r]
Nov 12 21:39:00.17: [ 2475]: --> [2:OK]
Nov 12 21:39:00.17: [ 2475]: DIAL 2
Nov 12 21:39:00.17: [ 2475]: <-- [6:ATDT2\r]
Nov 12 21:39:12.87: [ 2475]: --> [79:+FHR:FF 03 20 00 00 0E 00 00 00 96 0F 01 03 00 10 10 05 02 95 C8 08 01 49 02 50]
Nov 12 21:39:13.01: [ 2475]: --> [48:45 4E 43 4F 4D 20 4B 46 54 2E 20 20 20 20 20 03 ]
Nov 12 21:39:13.01: [ 2475]: SEND FAILED: JOB 6 DEST 2 ERR Unknown problem (check modem power)
Nov 12 21:39:13.01: [ 2475]: <-- [5:ATH0\r]
Nov 12 21:39:13.01: [ 2475]: --> [5:+FCON]
Nov 12 21:39:13.01: [ 2475]: --> [71:+FNSF:0,0,14,0,0,0,150,15,1,3,0,16,5,2,149,200,8,1,73,2,80,69,78,67,79,]
Nov 12 21:39:13.13: [ 2475]: --> [34:77,32,75,70,84,46,32,32,32,32,32,3]
Nov 12 21:39:13.13: [ 2475]: --> [7:+FHNG:2]
Nov 12 21:39:13.13: [ 2475]: REMOTE HANGUP: Call aborted,  from +FK or <CAN> (code 2)
Nov 12 21:39:13.33: [ 2475]: --> [2:OK]
Nov 12 21:39:13.33: [ 2475]: MODEM set DTR OFF
Nov 12 21:39:13.33: [ 2475]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Nov 12 21:39:13.33: [ 2475]: SESSION END

 

Please help if U can!

 

Thanks