[hylafax-users] Failed to properly detect high-speed data carrier

["santillan@xxxxxxxxx" <santillan@xxxxxxxxx>]

Hello everyone,

I am trying to setup a fax server. Outgoing faxes are sent ok, but there 
are problems when receiving incoming faxes.
There are some sites where the fax is received ok, but there are 
particular sites when this problem occurs. This usually
happens when there are many pages being sent to the faxserver. I have 
noticed however that the error message is always the same
: "Failed to properly detect high-speed data carrier"

I have tried changing the configuration of the modem from xonxoff 
(software flowcontrol) to rtscts (hardware flow control) but
the problem still persists.

The system consists of the following :
Intel Pentium 120MHz CPU
USR Sportster 33600 FAX Modem v4.3.179
Slackware Linux 10.0
Hylafax-4.2.0
patched libtiff-3.6.1

I included part of the log on this post. I removed some parts as it is long.

=====================================================

Oct 19 16:35:23.22: [19275]: SESSION BEGIN 000001024 632620
Oct 19 16:35:23.22: [19275]: HylaFAX (tm) Version 4.2.0
Oct 19 16:35:23.22: [19275]: <-- [22:AT+FCLASS=1&H1&I0&R2A\r]
Oct 19 16:35:28.52: [19275]: --> [7:CONNECT]
Oct 19 16:35:28.52: [19275]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Oct 19 16:35:28.52: [19275]: RECV FAX: begin
Oct 19 16:35:28.53: [19275]: <-- data [32]
Oct 19 16:35:28.54: [19275]: <-- data [2]
Oct 19 16:35:28.58: [19275]: --> [7:CONNECT]
Oct 19 16:35:28.58: [19275]: <-- data [23]
Oct 19 16:35:28.58: [19275]: <-- data [2]
Oct 19 16:35:29.30: [19275]: --> [7:CONNECT]
Oct 19 16:35:29.30: [19275]: <-- data [10]
Oct 19 16:35:29.30: [19275]: <-- data [2]
Oct 19 16:35:31.48: [19275]: --> [2:OK]
Oct 19 16:35:31.49: [19275]: <-- [9:AT+FRH=3\r]
Oct 19 16:35:33.92: [19275]: --> [7:CONNECT]
Oct 19 16:35:35.51: [19275]: --> [2:OK]
:
:
:
:
Oct 19 16:36:23.31: [19275]: RECV received frame number 6
Oct 19 16:36:23.31: [19275]: RECV received RCP frame
Oct 19 16:36:23.50: [19275]: --> [10:NO CARRIER]
Oct 19 16:36:23.50: [19275]: <-- [9:AT+FRH=3\r]
Oct 19 16:36:23.88: [19275]: --> [7:CONNECT]
Oct 19 16:36:24.91: [19275]: --> [2:OK]
Oct 19 16:36:24.91: [19275]: RECV recv PPS (partial page signal)
Oct 19 16:36:24.91: [19275]: RECV recv MPS (more pages, same document)
Oct 19 16:36:24.91: [19275]: RECV received 7 frames of block 1 of page 4
Oct 19 16:36:24.91: [19275]: <-- [9:AT+FRS=7\r]
Oct 19 16:36:25.02: [19275]: --> [2:OK]
Oct 19 16:36:25.03: [19275]: <-- [9:AT+FTH=3\r]
Oct 19 16:36:28.02: [19275]: --> [0:]
Oct 19 16:36:28.02: [19275]: RECV send PPR (partial page request)
Oct 19 16:36:28.02: [19275]: <-- [10:AT+FRM=72\r]
Oct 19 16:36:28.27: [19275]: --> [9:AT+FRM=72]
Oct 19 16:36:28.27: [19275]: RECV keeping unconfirmed page
Oct 19 16:36:28.30: [19275]: RECV: 1792 bytes of data, 16 total lines
Oct 19 16:36:28.31: [19275]: RECV FAX (000001024): from 81454765271, 
page 4 in 0:12, INF, 200 x 100 dpi, 2-D MMR, 7200 bit/s
Oct 19 16:36:28.36: [19275]: RECV FAX (000001024): 
recvq/fax000000293.tif from 81454765271, route to <unspecified>, 4 pages 
in 1:00
Oct 19 16:36:28.38: [19275]: RECV FAX: Failed to properly detect 
high-speed data carrier.
Oct 19 16:36:28.38: [19275]: <-- [9:AT+FTH=3\r]
Oct 19 16:36:28.38: [19275]: --> [5:ERROR]
Oct 19 16:36:28.39: [19275]: RECV FAX (000001024): session with 
81454765271 terminated abnormally: Failed to properly detect high-speed 
data carrier.
Oct 19 16:36:28.39: [19275]: RECV FAX: bin/faxrcvd 
"recvq/fax000000293.tif" "ttyS0" "000001024" "Failed to properly detect 
high-speed data carrier." "" ""
Oct 19 16:36:28.40: [19275]: RECV FAX: end
Oct 19 16:36:28.40: [19275]: SESSION END
=======================================================

Has anyone encountered this problem before?
Is it a line problem?
Or does the modem have a problem?

Any help would be appreciated.
Thanks in advance.

Regards,
Jay Santillan



____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*