HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] T.30 T2 timeout, expected page not received



> Hi I have this error:
>
> Oct 18 12:16:18.85: [21976]: SESSION BEGIN 000000005 390818420130
> Oct 18 12:16:18.85: [21976]: HylaFAX (tm) Version 4.2.0
> Oct 18 12:16:18.85: [21976]: <-- [4:ATA\r]
> Oct 18 12:16:23.85: [21976]: --> [7:CONNECT]
> Oct 18 12:16:23.85: [21976]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
> Oct 18 12:16:23.85: [21976]: RECV FAX: begin
> Oct 18 12:16:23.85: [21976]: <-- data [32]
> Oct 18 12:16:23.85: [21976]: <-- data [2]
> Oct 18 12:16:25.23: [21976]: --> [7:CONNECT]
> Oct 18 12:16:25.23: [21976]: <-- data [23]
> Oct 18 12:16:25.23: [21976]: <-- data [2]
> Oct 18 12:16:25.99: [21976]: --> [7:CONNECT]
> Oct 18 12:16:25.99: [21976]: <-- data [10]
> Oct 18 12:16:25.99: [21976]: <-- data [2]
> Oct 18 12:16:26.43: [21976]: --> [2:OK]
> Oct 18 12:16:26.43: [21976]: <-- [9:AT+FRH=3\r]
> Oct 18 12:16:27.14: [21976]: --> [7:CONNECT]
> Oct 18 12:16:28.96: [21976]: --> [2:OK]
> Oct 18 12:16:28.96: [21976]: REMOTE TSI "0547330781"
> Oct 18 12:16:28.96: [21976]: <-- [9:AT+FRH=3\r]
> Oct 18 12:16:28.99: [21976]: --> [7:CONNECT]
> Oct 18 12:16:29.31: [21976]: --> [2:OK]
> Oct 18 12:16:29.31: [21976]: REMOTE wants 9600 bit/s
> Oct 18 12:16:29.31: [21976]: REMOTE wants A4 page width (215 mm)
> Oct 18 12:16:29.31: [21976]: REMOTE wants unlimited page length
> Oct 18 12:16:29.31: [21976]: REMOTE wants 3.85 line/mm
> Oct 18 12:16:29.31: [21976]: REMOTE wants 1-D MH
> Oct 18 12:16:29.31: [21976]: RECV training at v.29 9600 bit/s
> Oct 18 12:16:29.31: [21976]: <-- [10:AT+FRM=96\r]
> Oct 18 12:16:29.66: [21976]: --> [7:CONNECT]
> Oct 18 12:16:31.17: [21976]: RECV: TCF 1792 bytes, 0% non-zero, 1778
> zero-run
> Oct 18 12:16:31.18: [21976]: --> [10:NO CARRIER]
> Oct 18 12:16:31.18: [21976]: DELAY 75 ms
> Oct 18 12:16:31.26: [21976]: TRAINING succeeded
> Oct 18 12:16:31.26: [21976]: <-- [9:AT+FTH=3\r]
> Oct 18 12:16:31.30: [21976]: --> [7:CONNECT]
> Oct 18 12:16:31.30: [21976]: <-- data [3]
> Oct 18 12:16:31.30: [21976]: <-- data [2]
> Oct 18 12:16:32.04: [21976]: --> [2:OK]
> Oct 18 12:16:32.04: [21976]: <-- [10:AT+FRM=96\r]
> Oct 18 12:16:32.79: [21976]: --> [7:CONNECT]
> Oct 18 12:16:32.79: [21976]: RECV: begin page
> Oct 18 12:16:53.99: [21976]: RECV: 343 total lines, 9 bad lines, 3
> consecutive bad lines
> Oct 18 12:16:53.99: [21976]: RECV: end page
> Oct 18 12:16:53.99: [21976]: --> [10:NO CARRIER]
> Oct 18 12:16:53.99: [21976]: <-- [9:AT+FRH=3\r]
> Oct 18 12:16:54.46: [21976]: --> [7:CONNECT]
> Oct 18 12:16:59.46: [21976]: <-- data [1]
> Oct 18 12:16:59.57: [21976]: --> [2:OK]
> Oct 18 12:16:59.57: [21976]: RECV keeping unconfirmed page
> Oct 18 12:16:59.57: [21976]: RECV FAX (000000005): from 0547330781, page 1
> in 0:28, INF, 3.85 line/mm, 1-D MH, 9600 bit/s
> Oct 18 12:16:59.57: [21976]: RECV FAX (000000005): recvq/fax000000005.tif
> from 0547330781, route to <unspecified>, 1 pages in 0:36
> Oct 18 12:16:59.57: [21976]: RECV FAX: T.30 T2 timeout, expected page not
> received
> Oct 18 12:16:59.57: [21976]: <-- [9:AT+FTH=3\r]
> Oct 18 12:16:59.71: [21976]: --> [7:CONNECT]
> Oct 18 12:16:59.71: [21976]: <-- data [3]
> Oct 18 12:16:59.71: [21976]: <-- data [2]
> Oct 18 12:17:00.45: [21976]: --> [2:OK]
> Oct 18 12:17:00.45: [21976]: RECV FAX (000000005): session with 0547330781
> terminated abnormally: T.30 T2 timeout, expected page not
>  received
> Oct 18 12:17:00.45: [21976]: RECV FAX: bin/faxrcvd
"recvq/fax000000005.tif"
> "ttyS0" "000000005" "T.30 T2 timeout, expected page not
> received" "" ""
> Oct 18 12:17:00.45: [21976]: RECV FAX: end
> Oct 18 12:17:00.46: [21976]: SESSION END
>
> This is my conf:
>
> CountryCode:            39
> AreaCode:               2
> FAXNumber:              +39.xxx.xxx.xxx.xx
> LongDistancePrefix:     5
> InternationalPrefix:    011
> DialStringRules:        etc/dialrules
> ServerTracing:          1
> SessionTracing:         11
> RecvFileMode:           0600
> LogFileMode:            0600
> DeviceMode:             0600
> RingsBeforeAnswer:      1
> SpeakerVolume:          off
> GettyArgs:              "-h %l dx_%s"
> LocalIdentifier:        "NothingSetup"
> TagLineFont:            etc/lutRS18.pcf
> TagLineFormat:          "From %%l|%c|Page %%P of %%T"
> PercentGoodLines:       90
> MaxRecvPages:           25
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType:              Class1          # use this to supply a hint
> ModemRate:              57600           # rate for DCE-DTE communication
> ModemFlowControl:       rtscts          # RTS/CTS flow control assumed
> #
> ModemSoftFlowCmd:       AT\Q1           # set desired flow control method
> ModemHardFlowCmd:       AT\Q3           # set desired flow control method
> ModemSetupDTRCmd:       AT&D3           # setup so DTR drop resets modem
> ModemSetupDCDCmd:       AT&C1           # setup so DCD follows carrier
> ModemDialCmd:           ATDT%s
> #
> # Happy days!  This modem has proper support for querying
> # the model, manufacturer, and firmware revision!
> #
> ModemMfrQueryCmd:       AT+FMFR?
> ModemModelQueryCmd:     AT+FMDL?
> ModemRevQueryCmd:       AT+FREV?
>
> Class1SwitchingCmd:  "<delay:7>"
>
> Ideas?
>
> Ciro La Ferrara


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




Project hosted by iFAX Solutions