 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: [hylafax-users] No Response to PPS repeat 3 times
- To: Lee Howard <faxguy@xxxxxxxxxxxxxxxx>
- Subject: Re: [hylafax-users] No Response to PPS repeat 3 times
- From: Umer Farooq <umer@xxxxxxxxxxxx>
- Cc: hylafax-users@xxxxxxxxxxx
- Date: Mon, 23 Aug 2004 20:28:35 -0400
Change config/topic no diffrence.. I think switching to MultiTech is the answer..
Full log file is below..
Aug 23 18:09:25.82: [ 1501]: SESSION BEGIN 000000003 18474985283
Aug 23 18:09:25.82: [ 1501]: HylaFAX (tm) Version 4.2.0
Aug 23 18:09:25.82: [ 1501]: SEND FAX: JOB 2 DEST 18474985283 COMMID 000000003 DEVICE '/dev/ttyS4'
Aug 23 18:09:25.82: [ 1501]: <-- [12:AT+FCLASS=1\r]
Aug 23 18:09:25.94: [ 1501]: --> [2:OK]
Aug 23 18:09:25.94: [ 1501]: DIAL 18474985283
Aug 23 18:09:25.94: [ 1501]: <-- [16:ATDT18474985283\r]
Aug 23 18:09:39.40: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:41.16: [ 1501]: --> [2:OK]
Aug 23 18:09:41.16: [ 1501]: REMOTE NSF "00 00 09 00 08 2D 84 7F FF FF FF FF FF FF FF FF FF FF 01 6C 02 0A 10 01 02 01 30
"
Aug 23 18:09:41.16: [ 1501]: NSF remote fax equipment: Xerox/Toshiba
Aug 23 18:09:41.16: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:09:41.18: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:41.88: [ 1501]: --> [2:OK]
Aug 23 18:09:41.88: [ 1501]: REMOTE CSI "+8474985283"
Aug 23 18:09:41.88: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:09:41.90: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:42.33: [ 1501]: --> [2:OK]
Aug 23 18:09:42.33: [ 1501]: REMOTE best rate 33600 bit/s
Aug 23 18:09:42.33: [ 1501]: REMOTE max A4 page width (215 mm)
Aug 23 18:09:42.33: [ 1501]: REMOTE max unlimited page length
Aug 23 18:09:42.33: [ 1501]: REMOTE best vres R16 x 15.4 line/mm
Aug 23 18:09:42.33: [ 1501]: REMOTE best format 2-D MMR
Aug 23 18:09:42.33: [ 1501]: REMOTE supports T.30 Annex A, 256-byte ECM
Aug 23 18:09:42.33: [ 1501]: REMOTE best 5 ms/scanline
Aug 23 18:09:42.33: [ 1501]: USE 14400 bit/s
Aug 23 18:09:42.33: [ 1501]: USE error correction mode
Aug 23 18:09:42.33: [ 1501]: USE 0 ms/scanline
Aug 23 18:09:42.33: [ 1501]: SEND file "docq/doc2.ps;30"
Aug 23 18:09:42.33: [ 1501]: USE A4 page width (215 mm)
Aug 23 18:09:42.33: [ 1501]: USE unlimited page length
Aug 23 18:09:42.33: [ 1501]: USE 3.85 line/mm
Aug 23 18:09:42.33: [ 1501]: USE 2-D MMR
Aug 23 18:09:42.33: [ 1501]: SEND training at v.17 14400 bit/s
Aug 23 18:09:42.33: [ 1501]: <-- [9:AT+FTH=3\r]
Aug 23 18:09:42.53: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:42.53: [ 1501]: <-- data [23]
Aug 23 18:09:42.53: [ 1501]: <-- data [2]
Aug 23 18:09:42.55: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:42.55: [ 1501]: <-- data [7]
Aug 23 18:09:42.55: [ 1501]: <-- data [2]
Aug 23 18:09:44.53: [ 1501]: --> [2:OK]
Aug 23 18:09:44.53: [ 1501]: <-- [9:AT+FTS=7\r]
Aug 23 18:09:44.61: [ 1501]: --> [2:OK]
Aug 23 18:09:44.61: [ 1501]: <-- [11:AT+FTM=145\r]
Aug 23 18:09:46.09: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:46.09: [ 1501]: <-- data [1024]
Aug 23 18:09:46.09: [ 1501]: <-- data [1024]
Aug 23 18:09:46.09: [ 1501]: <-- data [652]
Aug 23 18:09:46.09: [ 1501]: <-- data [2]
Aug 23 18:09:47.62: [ 1501]: --> [2:OK]
Aug 23 18:09:47.62: [ 1501]: <-- [9:AT+FRS=1\r]
Aug 23 18:09:47.64: [ 1501]: --> [2:OK]
Aug 23 18:09:47.64: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:09:48.54: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:49.64: [ 1501]: --> [2:OK]
Aug 23 18:09:49.64: [ 1501]: SEND training at v.17 12000 bit/s
Aug 23 18:09:49.64: [ 1501]: <-- [9:AT+FTH=3\r]
Aug 23 18:09:49.83: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:49.83: [ 1501]: <-- data [23]
Aug 23 18:09:49.83: [ 1501]: <-- data [2]
Aug 23 18:09:49.85: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:49.85: [ 1501]: <-- data [7]
Aug 23 18:09:49.85: [ 1501]: <-- data [2]
Aug 23 18:09:51.84: [ 1501]: --> [2:OK]
Aug 23 18:09:51.84: [ 1501]: <-- [9:AT+FTS=7\r]
Aug 23 18:09:51.92: [ 1501]: --> [2:OK]
Aug 23 18:09:51.92: [ 1501]: <-- [11:AT+FTM=121\r]
Aug 23 18:09:53.40: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:53.40: [ 1501]: <-- data [1024]
Aug 23 18:09:53.40: [ 1501]: <-- data [1024]
Aug 23 18:09:53.40: [ 1501]: <-- data [202]
Aug 23 18:09:53.40: [ 1501]: <-- data [2]
Aug 23 18:09:54.93: [ 1501]: --> [2:OK]
Aug 23 18:09:54.93: [ 1501]: <-- [9:AT+FRS=1\r]
Aug 23 18:09:54.95: [ 1501]: --> [2:OK]
Aug 23 18:09:54.95: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:09:56.09: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:56.97: [ 1501]: --> [2:OK]
Aug 23 18:09:56.97: [ 1501]: SEND training at v.17 9600 bit/s
Aug 23 18:09:56.97: [ 1501]: <-- [9:AT+FTH=3\r]
Aug 23 18:09:57.16: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:57.16: [ 1501]: <-- data [23]
Aug 23 18:09:57.16: [ 1501]: <-- data [2]
Aug 23 18:09:57.18: [ 1501]: --> [7:CONNECT]
Aug 23 18:09:57.18: [ 1501]: <-- data [7]
Aug 23 18:09:57.18: [ 1501]: <-- data [2]
Aug 23 18:09:59.17: [ 1501]: --> [2:OK]
Aug 23 18:09:59.17: [ 1501]: <-- [9:AT+FTS=7\r]
Aug 23 18:09:59.25: [ 1501]: --> [2:OK]
Aug 23 18:09:59.25: [ 1501]: <-- [10:AT+FTM=97\r]
Aug 23 18:10:00.73: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:00.73: [ 1501]: <-- data [1024]
Aug 23 18:10:00.73: [ 1501]: <-- data [776]
Aug 23 18:10:00.73: [ 1501]: <-- data [2]
Aug 23 18:10:02.26: [ 1501]: --> [2:OK]
Aug 23 18:10:02.26: [ 1501]: <-- [9:AT+FRS=1\r]
Aug 23 18:10:02.28: [ 1501]: --> [2:OK]
Aug 23 18:10:02.28: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:10:03.30: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:04.43: [ 1501]: --> [2:OK]
Aug 23 18:10:04.43: [ 1501]: TRAINING succeeded
Aug 23 18:10:04.43: [ 1501]: SEND begin page
Aug 23 18:10:04.43: [ 1501]: Reading MH-compressed image file
Aug 23 18:10:04.43: [ 1501]: SEND EOFB
Aug 23 18:10:04.43: [ 1501]: SEND send frame number 0
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 1
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 2
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 3
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 4
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 5
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 6
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 7
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 8
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 9
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 10
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 11
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 12
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 13
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 14
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 15
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 16
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 17
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 18
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 19
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 20
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 21
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 22
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 23
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 24
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 25
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 26
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 27
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 28
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 29
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 30
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 31
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 32
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 33
Aug 23 18:10:04.44: [ 1501]: SEND send frame number 34
Aug 23 18:10:04.44: [ 1501]: DELAY 200 ms
Aug 23 18:10:04.63: [ 1501]: <-- [10:AT+FTM=98\r]
Aug 23 18:10:04.89: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:04.89: [ 1501]: <-- data [1035]
Aug 23 18:10:04.89: [ 1501]: <-- data [1032]
Aug 23 18:10:04.89: [ 1501]: <-- data [1035]
Aug 23 18:10:04.89: [ 1501]: <-- data [1034]
Aug 23 18:10:06.50: [ 1501]: <-- data [1045]
Aug 23 18:10:06.50: [ 1501]: <-- data [1036]
Aug 23 18:10:06.50: [ 1501]: <-- data [1035]
Aug 23 18:10:06.50: [ 1501]: <-- data [1038]
Aug 23 18:10:08.39: [ 1501]: <-- data [1047]
Aug 23 18:10:08.39: [ 1501]: <-- data [422]
Aug 23 18:10:08.39: [ 1501]: <-- data [2]
Aug 23 18:10:12.95: [ 1501]: --> [2:OK]
Aug 23 18:10:12.95: [ 1501]: <-- [9:AT+FTS=7\r]
Aug 23 18:10:13.03: [ 1501]: --> [2:OK]
Aug 23 18:10:13.03: [ 1501]: <-- [9:AT+FTH=3\r]
Aug 23 18:10:13.19: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:13.19: [ 1501]: <-- data [7]
Aug 23 18:10:13.19: [ 1501]: <-- data [2]
Aug 23 18:10:14.47: [ 1501]: --> [2:OK]
Aug 23 18:10:14.47: [ 1501]: SEND send PPS (partial page signal)
Aug 23 18:10:14.47: [ 1501]: SEND send MPS (more pages, same document)
Aug 23 18:10:14.47: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:10:14.94: [ 1501]: --> [10:NO CARRIER]
Aug 23 18:10:14.94: [ 1501]: MODEM No carrier
Aug 23 18:10:14.94: [ 1501]: <-- [9:AT+FTH=3\r]
Aug 23 18:10:15.14: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:15.14: [ 1501]: <-- data [7]
Aug 23 18:10:15.14: [ 1501]: <-- data [2]
Aug 23 18:10:16.42: [ 1501]: --> [2:OK]
Aug 23 18:10:16.42: [ 1501]: SEND send PPS (partial page signal)
Aug 23 18:10:16.42: [ 1501]: SEND send MPS (more pages, same document)
Aug 23 18:10:16.42: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:10:17.50: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:17.51: [ 1501]: --> [5:ERROR]
Aug 23 18:10:17.51: [ 1501]: MODEM Command error
Aug 23 18:10:17.51: [ 1501]: FCS error
Aug 23 18:10:17.51: [ 1501]: <-- [9:AT+FTH=3\r]
Aug 23 18:10:17.71: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:17.71: [ 1501]: <-- data [7]
Aug 23 18:10:17.71: [ 1501]: <-- data [2]
Aug 23 18:10:18.99: [ 1501]: --> [2:OK]
Aug 23 18:10:18.99: [ 1501]: SEND send PPS (partial page signal)
Aug 23 18:10:18.99: [ 1501]: SEND send MPS (more pages, same document)
Aug 23 18:10:18.99: [ 1501]: <-- [9:AT+FRH=3\r]
Aug 23 18:10:19.30: [ 1501]: --> [10:NO CARRIER]
Aug 23 18:10:19.30: [ 1501]: MODEM No carrier
Aug 23 18:10:19.30: [ 1501]: No response to PPS repeated 3 times.
Aug 23 18:10:19.30: [ 1501]: SEND end page
Aug 23 18:10:19.30: [ 1501]: <-- [9:AT+FTH=3\r]
Aug 23 18:10:19.50: [ 1501]: --> [7:CONNECT]
Aug 23 18:10:19.50: [ 1501]: <-- data [3]
Aug 23 18:10:19.50: [ 1501]: <-- data [2]
Aug 23 18:10:20.67: [ 1501]: --> [2:OK]
Aug 23 18:10:20.67: [ 1501]: <-- [5:ATH0\r]
Aug 23 18:10:20.79: [ 1501]: --> [2:OK]
Aug 23 18:10:20.79: [ 1501]: SESSION END
Lee Howard wrote:
On 2004.08.23 16:28 Umer Farooq wrote:
Hi,
I'm having issues with sending faxes to Toshiba 125DP fax machine.. I keep on getting this PPS error.. no problem with other fax machines
If I switch to Class2.0 it works fine.. but then on some other numbers.. I get No Response to MPS error..
Can anyone shed some light on this..
Currently using USR5610B modem.. would switching to MultiTech solv the problem..
Oh.. it sends the cover sheet.. or once in a while.. it would go up to 4 to 7 pages in transmission before.. I get this message..
HylaFax4.2.0. RH 2.1AS
Aug 23 18:10:17.71: [ 1501]: <-- data [2] Aug 23 18:10:18.99: [ 1501]: --> [2:OK] Aug 23 18:10:18.99: [ 1501]: SEND send PPS (partial page signal) Aug 23 18:10:18.99: [ 1501]: SEND send MPS (more pages, same document) Aug 23 18:10:18.99: [ 1501]: <-- [9:AT+FRH=3\r] Aug 23 18:10:19.30: [ 1501]: --> [10:NO CARRIER] Aug 23 18:10:19.30: [ 1501]: MODEM No carrier Aug 23 18:10:19.30: [ 1501]: No response to PPS repeated 3 times. Aug 23 18:10:19.30: [ 1501]: SEND end page Aug 23 18:10:19.30: [ 1501]: <-- [9:AT+FTH=3\r] Aug 23 18:10:19.50: [ 1501]: --> [7:CONNECT] Aug 23 18:10:19.50: [ 1501]: <-- data [3] Aug 23 18:10:19.50: [ 1501]: <-- data [2]
I think that if you were to look at more of the log you would see some kind of modem problem soon after an AT+FRS=n or AT+FTS=n. It turns out that some USR modems can react badly to these commands sometimes. You may want to look at the Topic default configuration file (config/topic) and change the *WaitCmds to the <delay:n> settings. Then try that. Or yes, you could use a modem other than USR like a MultiTech.
This is just a guess, though, as you didn't show the whole log.
Lee.
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
-- Umer Farooq Octadyne Systems umer@xxxxxxxxxxxx +1 (519) 635-2795 voice +1 (208) 275-3824 fax
LOOKING FOR A USED CAR IN IOWA VISIT: http://www.IowaMotors.com
WARNING: ------------------------------- The information contained in this document and attachments is confidential and intended only for the person(s) named above. If you are not the intended recipient you are hereby notified that any disclosure, copying, distribution, or any other use of the information is strictly prohibited. If you have received this document by mistake, please notify the sender immediately and destroy this document and attachments without making any copy of any kind.
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- References:
- [hylafax-users] No Response to PPS repeat 3 times
- From: Umer Farooq
- Re: [hylafax-users] No Response to PPS repeat 3 times
- From: Lee Howard
- [hylafax-users] No Response to PPS repeat 3 times
- Prev by Date: Re: [hylafax-users] Modem Command Errors
- Next by Date: [hylafax-users] RE : Multiple modems
- Previous by thread: Re: [hylafax-users] No Response to PPS repeat 3 times
- Next by thread: [hylafax-users] RE : Multiple modems
- Index(es):
Project hosted by iFAX Solutions