 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: [hylafax-users] Recieve Errors
- To: <hylafax-users@xxxxxxxxxxx>
- Subject: Re: [hylafax-users] Recieve Errors
- From: Stephen Carville <stephen@xxxxxxxxxxxxxx>
- Date: Wed, 18 Aug 2004 16:40:16 -0700 (PDT)
On Tue, 17 Aug 2004, Lee Howard wrote:
- On 2004.08.17 14:12 Stephen Carville wrote:
-
- > Aug 17 13:27:09.16: [ 2244]: REMOTE wants 9600 bit/s
- > Aug 17 13:27:09.16: [ 2244]: REMOTE wants A4 page width (215 mm)
- > Aug 17 13:27:09.16: [ 2244]: REMOTE wants unlimited page length
- > Aug 17 13:27:09.16: [ 2244]: REMOTE wants 3.85 line/mm
- > Aug 17 13:27:09.16: [ 2244]: REMOTE wants 1-D MH
- > Aug 17 13:27:09.16: [ 2244]: REMOTE wants T.30 Annex A, 256-byte ECM
- > Aug 17 13:27:09.16: [ 2244]: <-- [9:AT+FRH=3\r]
- > Aug 17 13:27:09.22: [ 2244]: --> [7:CONNECT]
- > Aug 17 13:27:09.25: [ 2244]: --> [2:^P^C]
- > Aug 17 13:27:09.28: [ 2244]: --> [10:NO CARRIER]
- > Aug 17 13:27:09.28: [ 2244]: RECV training at v.29 9600 bit/s
- > Aug 17 13:27:09.28: [ 2244]: <-- [10:AT+FRM=96\r]
- > Aug 17 13:27:13.78: [ 2244]: --> [0:]
-
- Try removing Class1TCFRecvHack from your modem config and see what
- happens.
That seem to have cleared up the connection problem but a new --
possibly unrelated -- problem has cropped up:
The full document was not received because:
Failed to properly detect high-speed data carrier.
---- Transcript of session follows ----
Aug 18 14:55:20.44: [ 9190]: SESSION BEGIN 000001500 18003854994
Aug 18 14:55:20.44: [ 9190]: HylaFAX (tm) Version 4.2.0rc2
Aug 18 14:55:20.44: [ 9190]: <-- [4:ATA\r]
Aug 18 14:55:32.27: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:32.27: [ 9190]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyM1a'
Aug 18 14:55:32.27: [ 9190]: RECV FAX: begin
Aug 18 14:55:32.34: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:32.40: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:34.63: [ 9190]: --> [2:OK]
Aug 18 14:55:34.63: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:55:34.75: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:36.52: [ 9190]: --> [2:OK]
Aug 18 14:55:36.52: [ 9190]: REMOTE TSI "8003473941"
Aug 18 14:55:36.52: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:55:36.60: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:36.84: [ 9190]: --> [2:OK]
Aug 18 14:55:36.84: [ 9190]: REMOTE wants 14400 bit/s
Aug 18 14:55:36.84: [ 9190]: REMOTE wants A4 page width (215 mm)
Aug 18 14:55:36.84: [ 9190]: REMOTE wants unlimited page length
Aug 18 14:55:36.84: [ 9190]: REMOTE wants 3.85 line/mm
Aug 18 14:55:36.84: [ 9190]: REMOTE wants 2-D MMR
Aug 18 14:55:36.84: [ 9190]: REMOTE wants T.30 Annex A, 256-byte ECM
Aug 18 14:55:36.84: [ 9190]: RECV training at v.17 14400 bit/s
Aug 18 14:55:36.84: [ 9190]: <-- [11:AT+FRM=145\r]
Aug 18 14:55:38.63: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:40.18: [ 9190]: RECV: TCF 2704 bytes, 1% non-zero, 1098 zero-run
Aug 18 14:55:40.18: [ 9190]: RECV: reject TCF (zero run too short, min 1800)
Aug 18 14:55:40.21: [ 9190]: --> [10:NO CARRIER]
Aug 18 14:55:40.21: [ 9190]: DELAY 75 ms
Aug 18 14:55:40.29: [ 9190]: <-- [9:AT+FTH=3\r]
Aug 18 14:55:41.32: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:41.74: [ 9190]: --> [2:OK]
Aug 18 14:55:41.74: [ 9190]: TRAINING failed
Aug 18 14:55:41.74: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:55:41.88: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:43.65: [ 9190]: --> [2:OK]
Aug 18 14:55:43.65: [ 9190]: REMOTE TSI "8003473941"
Aug 18 14:55:43.65: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:55:43.73: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:43.97: [ 9190]: --> [2:OK]
Aug 18 14:55:43.97: [ 9190]: REMOTE wants 14400 bit/s
Aug 18 14:55:43.97: [ 9190]: REMOTE wants A4 page width (215 mm)
Aug 18 14:55:43.97: [ 9190]: REMOTE wants unlimited page length
Aug 18 14:55:43.97: [ 9190]: REMOTE wants 3.85 line/mm
Aug 18 14:55:43.97: [ 9190]: REMOTE wants 2-D MMR
Aug 18 14:55:43.97: [ 9190]: REMOTE wants T.30 Annex A, 256-byte ECM
Aug 18 14:55:43.97: [ 9190]: RECV training at v.17 14400 bit/s
Aug 18 14:55:43.97: [ 9190]: <-- [11:AT+FRM=145\r]
Aug 18 14:55:45.76: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:47.31: [ 9190]: RECV: TCF 2704 bytes, 0% non-zero, 2158 zero-run
Aug 18 14:55:47.34: [ 9190]: --> [10:NO CARRIER]
Aug 18 14:55:47.34: [ 9190]: DELAY 75 ms
Aug 18 14:55:47.42: [ 9190]: TRAINING succeeded
Aug 18 14:55:47.42: [ 9190]: <-- [9:AT+FTH=3\r]
Aug 18 14:55:48.45: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:48.87: [ 9190]: --> [2:OK]
Aug 18 14:55:48.87: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:55:49.83: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:49.83: [ 9190]: Bad HDLC terminating flag received.
Aug 18 14:55:50.11: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0xf8
Aug 18 14:55:50.39: [ 9190]: Bad HDLC terminating flag received.
Aug 18 14:55:50.57: [ 9190]: RECV received frame number 3
Aug 18 14:55:50.76: [ 9190]: RECV received frame number 4
Aug 18 14:55:50.94: [ 9190]: RECV received frame number 5
Aug 18 14:55:51.03: [ 9190]: RECV received frame number 6
Aug 18 14:55:51.22: [ 9190]: RECV received frame number 7
Aug 18 14:55:51.31: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0xc0
Aug 18 14:55:51.68: [ 9190]: RECV received frame number 10
Aug 18 14:55:51.77: [ 9190]: RECV received frame number 11
Aug 18 14:55:51.77: [ 9190]: RECV frame FCS check failed
Aug 18 14:55:51.96: [ 9190]: RECV received frame number 12
Aug 18 14:55:52.05: [ 9190]: RECV received frame number 13
Aug 18 14:55:52.24: [ 9190]: RECV received frame number 14
Aug 18 14:55:52.24: [ 9190]: RECV frame FCS check failed
Aug 18 14:55:52.42: [ 9190]: RECV received frame number 15
Aug 18 14:55:52.51: [ 9190]: RECV received frame number 16
Aug 18 14:55:52.51: [ 9190]: RECV frame FCS check failed
Aug 18 14:55:52.70: [ 9190]: RECV received frame number 17
Aug 18 14:55:52.79: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0xfc
Aug 18 14:55:53.16: [ 9190]: RECV received frame number 20
Aug 18 14:55:53.16: [ 9190]: Bad HDLC terminating flag received.
Aug 18 14:55:53.25: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0
Aug 18 14:55:53.78: [ 9190]: RECV received frame number 23
Aug 18 14:55:53.78: [ 9190]: RECV received RCP frame
Aug 18 14:55:53.78: [ 9190]: --> [10:NO CARRIER]
Aug 18 14:55:53.78: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:55:53.90: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:55.02: [ 9190]: --> [2:OK]
Aug 18 14:55:55.02: [ 9190]: RECV recv PPS (partial page signal)
Aug 18 14:55:55.02: [ 9190]: RECV recv MPS (more pages, same document)
Aug 18 14:55:55.02: [ 9190]: RECV received 24 frames of block 1 of page 1
Aug 18 14:55:55.02: [ 9190]: <-- [9:AT+FRS=7\r]
Aug 18 14:55:55.14: [ 9190]: --> [2:OK]
Aug 18 14:55:55.14: [ 9190]: <-- [9:AT+FTH=3\r]
Aug 18 14:55:56.15: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:57.59: [ 9190]: --> [2:OK]
Aug 18 14:55:57.59: [ 9190]: RECV send PPR (partial page request)
Aug 18 14:55:57.59: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:55:58.54: [ 9190]: --> [7:CONNECT]
Aug 18 14:55:58.81: [ 9190]: RECV received frame number 0
Aug 18 14:55:59.00: [ 9190]: RECV received frame number 1
Aug 18 14:55:59.00: [ 9190]: RECV frame FCS check failed
Aug 18 14:55:59.18: [ 9190]: RECV received frame number 2
Aug 18 14:55:59.27: [ 9190]: RECV received frame number 8
Aug 18 14:55:59.46: [ 9190]: RECV received frame number 9
Aug 18 14:55:59.64: [ 9190]: RECV received frame number 11
Aug 18 14:55:59.73: [ 9190]: RECV received frame number 14
Aug 18 14:55:59.92: [ 9190]: RECV received frame number 16
Aug 18 14:56:00.01: [ 9190]: RECV received frame number 18
Aug 18 14:56:00.20: [ 9190]: RECV received frame number 19
Aug 18 14:56:00.38: [ 9190]: RECV received frame number 21
Aug 18 14:56:00.47: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0xfc
Aug 18 14:56:00.47: [ 9190]: RECV received RCP frame
Aug 18 14:56:00.72: [ 9190]: --> [10:NO CARRIER]
Aug 18 14:56:00.72: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:56:00.88: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:01.93: [ 9190]: --> [2:OK]
Aug 18 14:56:01.93: [ 9190]: RECV recv PPS (partial page signal)
Aug 18 14:56:01.93: [ 9190]: RECV recv MPS (more pages, same document)
Aug 18 14:56:01.93: [ 9190]: RECV received 12 frames of block 1 of page 1
Aug 18 14:56:01.93: [ 9190]: <-- [9:AT+FRS=7\r]
Aug 18 14:56:02.05: [ 9190]: --> [2:OK]
Aug 18 14:56:02.05: [ 9190]: <-- [9:AT+FTH=3\r]
Aug 18 14:56:03.08: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:04.53: [ 9190]: --> [2:OK]
Aug 18 14:56:04.53: [ 9190]: RECV send PPR (partial page request)
Aug 18 14:56:04.53: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:05.48: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:05.75: [ 9190]: RECV received frame number 1
Aug 18 14:56:05.94: [ 9190]: RECV received frame number 22
Aug 18 14:56:05.94: [ 9190]: RECV received RCP frame
Aug 18 14:56:06.10: [ 9190]: --> [10:NO CARRIER]
Aug 18 14:56:06.10: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:56:06.25: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:07.38: [ 9190]: --> [2:OK]
Aug 18 14:56:07.38: [ 9190]: RECV recv PPS (partial page signal)
Aug 18 14:56:07.38: [ 9190]: RECV recv MPS (more pages, same document)
Aug 18 14:56:07.38: [ 9190]: RECV received 2 frames of block 1 of page 1
Aug 18 14:56:07.38: [ 9190]: <-- [9:AT+FRS=7\r]
Aug 18 14:56:07.50: [ 9190]: --> [2:OK]
Aug 18 14:56:07.51: [ 9190]: RECV: 5919 bytes of data, 1065 total lines
Aug 18 14:56:07.51: [ 9190]: <-- [9:AT+FTH=3\r]
Aug 18 14:56:08.52: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:08.52: [ 9190]: RECV send MCF (message confirmation)
Aug 18 14:56:08.52: [ 9190]: RECV FAX (000001500): from 8003473941, page 1 in 0:21, INF, 3.85 line/mm, 2-D MMR, 14400 bit/s
Aug 18 14:56:08.96: [ 9190]: --> [2:OK]
Aug 18 14:56:08.96: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:09.90: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:10.18: [ 9190]: RECV received frame number 0
Aug 18 14:56:10.36: [ 9190]: RECV received frame number 1
Aug 18 14:56:10.54: [ 9190]: RECV received frame number 2
Aug 18 14:56:10.63: [ 9190]: RECV received frame number 3
Aug 18 14:56:10.82: [ 9190]: RECV received frame number 4
Aug 18 14:56:11.00: [ 9190]: RECV received frame number 5
Aug 18 14:56:11.09: [ 9190]: RECV received frame number 6
Aug 18 14:56:11.28: [ 9190]: RECV received frame number 7
Aug 18 14:56:11.37: [ 9190]: RECV received frame number 8
Aug 18 14:56:11.56: [ 9190]: RECV received frame number 9
Aug 18 14:56:11.74: [ 9190]: RECV received frame number 10
Aug 18 14:56:11.83: [ 9190]: RECV received frame number 11
Aug 18 14:56:12.02: [ 9190]: RECV received frame number 12
Aug 18 14:56:12.11: [ 9190]: RECV received frame number 13
Aug 18 14:56:12.29: [ 9190]: RECV received frame number 14
Aug 18 14:56:12.48: [ 9190]: RECV received frame number 15
Aug 18 14:56:12.57: [ 9190]: RECV received frame number 16
Aug 18 14:56:12.76: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0
Aug 18 14:56:13.03: [ 9190]: RECV received frame number 19
Aug 18 14:56:13.22: [ 9190]: RECV received frame number 20
Aug 18 14:56:13.31: [ 9190]: RECV received frame number 21
Aug 18 14:56:13.49: [ 9190]: RECV received frame number 22
Aug 18 14:56:13.68: [ 9190]: RECV received frame number 23
Aug 18 14:56:13.77: [ 9190]: RECV received frame number 24
Aug 18 14:56:13.87: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0
Aug 18 14:56:14.05: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0
Aug 18 14:56:14.42: [ 9190]: RECV received frame number 28
Aug 18 14:56:14.51: [ 9190]: RECV received frame number 29
Aug 18 14:56:14.51: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0xfc
Aug 18 14:56:14.79: [ 9190]: RECV received frame number 31
Aug 18 14:56:14.97: [ 9190]: RECV received frame number 32
Aug 18 14:56:15.16: [ 9190]: RECV received frame number 33
Aug 18 14:56:15.25: [ 9190]: RECV received frame number 34
Aug 18 14:56:15.43: [ 9190]: RECV received frame number 35
Aug 18 14:56:15.53: [ 9190]: RECV received frame number 36
Aug 18 14:56:15.71: [ 9190]: RECV received frame number 37
Aug 18 14:56:15.90: [ 9190]: RECV received frame number 38
Aug 18 14:56:15.99: [ 9190]: RECV received frame number 39
Aug 18 14:56:16.17: [ 9190]: RECV received frame number 40
Aug 18 14:56:16.27: [ 9190]: HDLC frame not byte-oriented. Trailing byte: 0
Aug 18 14:56:16.36: [ 9190]: Bad HDLC terminating flag received.
Aug 18 14:56:16.64: [ 9190]: RECV received frame number 43
Aug 18 14:56:16.73: [ 9190]: RECV received frame number 44
Aug 18 14:56:16.73: [ 9190]: RECV received RCP frame
Aug 18 14:56:16.89: [ 9190]: --> [10:NO CARRIER]
Aug 18 14:56:16.89: [ 9190]: <-- [9:AT+FRH=3\r]
Aug 18 14:56:17.02: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:18.20: [ 9190]: --> [2:OK]
Aug 18 14:56:18.20: [ 9190]: RECV recv PPS (partial page signal)
Aug 18 14:56:18.20: [ 9190]: RECV recv MPS (more pages, same document)
Aug 18 14:56:18.20: [ 9190]: RECV received 45 frames of block 1 of page 2
Aug 18 14:56:18.20: [ 9190]: <-- [9:AT+FRS=7\r]
Aug 18 14:56:18.32: [ 9190]: --> [2:OK]
Aug 18 14:56:18.32: [ 9190]: <-- [9:AT+FTH=3\r]
Aug 18 14:56:19.33: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:20.76: [ 9190]: --> [2:OK]
Aug 18 14:56:20.76: [ 9190]: RECV send PPR (partial page request)
Aug 18 14:56:20.76: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:21.05: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:21.05: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:21.32: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:21.32: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:21.61: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:21.61: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:21.88: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:21.88: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:22.23: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:22.23: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:25.42: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:25.42: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:25.71: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:25.71: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:25.98: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:25.98: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:26.27: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:26.27: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:26.60: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:26.60: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:29.79: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:29.79: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:30.08: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:30.08: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:30.35: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:30.35: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:30.62: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:30.62: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:30.95: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:30.95: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:34.16: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:34.16: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:34.43: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:34.43: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:34.72: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:34.72: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:34.99: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:34.99: [ 9190]: <-- [11:AT+FRM=146\r]
Aug 18 14:56:35.34: [ 9190]: --> [8:+FCERROR]
Aug 18 14:56:35.34: [ 9190]: RECV keeping unconfirmed page
Aug 18 14:56:35.36: [ 9190]: RECV: 11520 bytes of data, 279 total lines
Aug 18 14:56:35.36: [ 9190]: RECV FAX (000001500): from 8003473941, page 2 in 0:27, INF, 3.85 line/mm, 2-D MMR, 14400 bit/s
Aug 18 14:56:35.36: [ 9190]: RECV FAX (000001500): recvq/fax000005078.tif from 8003473941, route to <unspecified>, 2 pages in 1:03
Aug 18 14:56:35.36: [ 9190]: RECV FAX: Failed to properly detect high-speed data carrier.
Aug 18 14:56:35.36: [ 9190]: <-- [9:AT+FTH=3\r]
Aug 18 14:56:36.37: [ 9190]: --> [7:CONNECT]
Aug 18 14:56:36.81: [ 9190]: --> [2:OK]
Aug 18 14:56:36.81: [ 9190]: RECV FAX (000001500): session with 8003473941 terminated abnormally: Failed to properly detect high-speed data carrier.
Aug 18 14:56:36.81: [ 9190]: RECV FAX: bin/faxrcvd "recvq/fax000005078.tif" "ttyM1a" "000001500" "Failed to properly detect high-speed data carrier." "" ""
Aug 18 14:56:36.83: [ 9190]: RECV FAX: end
Aug 18 14:56:36.83: [ 9190]: SESSION END
The facsimile was automatically dispatched to: inbound-385-4994@xxxxxxxxxxxxxxx
Is this realated to Class1TCFRecvHack? I can't see how but I'm still
feeling my way thru this faxing stuff.
--
Stephen
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Recieve Errors
- From: Lee Howard
- Re: [hylafax-users] Recieve Errors
- References:
- Re: [hylafax-users] Recieve Errors
- From: Lee Howard
- Re: [hylafax-users] Recieve Errors
- Prev by Date: Re: [hylafax-users] Receiving some faxes, but not others
- Next by Date: Re: [hylafax-users] Recieve Errors
- Previous by thread: Re: [hylafax-users] Recieve Errors
- Next by thread: Re: [hylafax-users] Recieve Errors
- Index(es):
Project hosted by iFAX Solutions