Re: [hylafax-users] problem receiving faxes with Hylafax v4.2.0 alpha 023

[Daniel Moreda García <daniel.moreda@xxxxxxxxx>]

This is a session of the same fax, but with Hylafax v4.2.0beta2:

Aug 18 17:37:56.89: [ 3015]: SESSION BEGIN 000005165 34981xxxxxx
Aug 18 17:37:56.89: [ 3015]: HylaFAX (tm) Version 4.2.0beta2
Aug 18 17:37:56.89: [ 3015]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Aug 18 17:37:56.89: [ 3015]: <-- [4:ATA\r]
Aug 18 17:38:03.39: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:03.39: [ 3015]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS1'
Aug 18 17:38:03.39: [ 3015]: MODEM input buffering enabled
Aug 18 17:38:03.39: [ 3015]: RECV FAX: begin
Aug 18 17:38:03.39: [ 3015]: MODEM input buffering disabled
Aug 18 17:38:03.39: [ 3015]: <-- data [37]
Aug 18 17:38:03.39: [ 3015]: <-- data [2]
Aug 18 17:38:03.43: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:03.43: [ 3015]: <-- data [23]
Aug 18 17:38:03.43: [ 3015]: <-- data [2]
Aug 18 17:38:03.46: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:03.46: [ 3015]: <-- data [10]
Aug 18 17:38:03.46: [ 3015]: <-- data [2]
Aug 18 17:38:06.68: [ 3015]: --> [2:OK]
Aug 18 17:38:06.68: [ 3015]: <-- [9:AT+FRH=3\r]
Aug 18 17:38:07.38: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:08.95: [ 3015]: --> [2:OK]
Aug 18 17:38:08.95: [ 3015]: REMOTE TSI "34981xxxxxx"
Aug 18 17:38:08.95: [ 3015]: <-- [9:AT+FRH=3\r]
Aug 18 17:38:08.97: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:09.27: [ 3015]: --> [2:OK]
Aug 18 17:38:09.27: [ 3015]: REMOTE wants 14400 bit/s
Aug 18 17:38:09.27: [ 3015]: REMOTE wants A4 page width (215 mm)
Aug 18 17:38:09.27: [ 3015]: REMOTE wants unlimited page length
Aug 18 17:38:09.27: [ 3015]: REMOTE wants 3.85 line/mm
Aug 18 17:38:09.27: [ 3015]: REMOTE wants 1-D MH
Aug 18 17:38:09.27: [ 3015]: RECV training at v.17 14400 bit/s
Aug 18 17:38:09.27: [ 3015]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Aug 18 17:38:09.27: [ 3015]: <-- [11:AT+FRM=145\r]
Aug 18 17:38:10.98: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:12.75: [ 3015]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 18 17:38:12.75: [ 3015]: RECV: TCF 2520 bytes, 0% non-zero, 2520 zero-run
Aug 18 17:38:12.76: [ 3015]: --> [10:NO CARRIER]
Aug 18 17:38:12.76: [ 3015]: DELAY 75 ms
Aug 18 17:38:12.84: [ 3015]: TRAINING succeeded
Aug 18 17:38:12.84: [ 3015]: <-- [9:AT+FTH=3\r]
Aug 18 17:38:12.89: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:12.89: [ 3015]: <-- data [3]
Aug 18 17:38:12.89: [ 3015]: <-- data [2]
Aug 18 17:38:14.21: [ 3015]: --> [2:OK]
Aug 18 17:38:14.21: [ 3015]: MODEM input buffering enabled
Aug 18 17:38:14.21: [ 3015]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Aug 18 17:38:14.21: [ 3015]: <-- [11:AT+FRM=146\r]
Aug 18 17:38:15.44: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:15.44: [ 3015]: RECV: begin page
Aug 18 17:38:37.34: [ 3015]: RECV: 1090 total lines, 4 bad lines, 4 consecutive bad lines
Aug 18 17:38:37.34: [ 3015]: RECV: end page
Aug 18 17:38:37.34: [ 3015]: --> [10:NO CARRIER]
Aug 18 17:38:37.34: [ 3015]: <-- [9:AT+FRH=3\r]
Aug 18 17:38:37.60: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:38.61: [ 3015]: --> [2:OK]
Aug 18 17:38:38.61: [ 3015]: RECV recv EOP (no more pages or documents)
Aug 18 17:38:38.61: [ 3015]: DELAY 70 ms
Aug 18 17:38:38.68: [ 3015]: <-- [9:AT+FTH=3\r]
Aug 18 17:38:38.83: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:38.83: [ 3015]: <-- data [3]
Aug 18 17:38:38.83: [ 3015]: <-- data [2]
Aug 18 17:38:40.14: [ 3015]: --> [2:OK]
Aug 18 17:38:40.14: [ 3015]: RECV send MCF (message confirmation)
Aug 18 17:38:40.14: [ 3015]: RECV FAX (000005165): from 34981495680, page 1 in 0:28, INF, 
3.85 line/mm, 1-D MH, 14400 bit/s
Aug 18 17:38:40.14: [ 3015]: RECV FAX (000005165): recvq/fax000004926.tif from 
34981495680, route to <unspecified>, 1 pages in 0:37
Aug 18 17:38:40.14: [ 3015]: <-- [9:AT+FRH=3\r]
Aug 18 17:38:40.84: [ 3015]: --> [7:CONNECT]
Aug 18 17:38:41.93: [ 3015]: --> [2:OK]
Aug 18 17:38:41.93: [ 3015]: MODEM input buffering enabled
Aug 18 17:38:41.93: [ 3015]: RECV FAX: bin/faxrcvd "recvq/fax000004926.tif" "ttyS1" 
"000005165" "" "" ""
Aug 18 17:38:41.95: [ 3015]: RECV FAX: end
Aug 18 17:38:41.95: [ 3015]: SESSION END

Lee Howard wrote:

> On 2004.08.18 04:35 Daniel Moreda García wrote:
>
> > Hello.
> >
> > I'm using SuSE SLES-8 (i386) VERSION = 8.1
> >
> > I updated Hylafax v4.2.0beta2 to Hylafax v4.2.0, and now I can´t 
> > receive faxes.
> >
> > Modem is Conceptronic C56EW 56kbps
> >
> > This is a log:
>
>
> Can you send a log from 4.2.0beta2 from a session with the same sender 
> as this log you just sent?
>
> > I turned back again to Hylafax v4.2.0beta2
> >
> > Is there any problem with Hylafax v4.2.0?
>
>
> No problem, to my knowlege, that would cause this.
>
> Lee.

--
Daniel Moreda García
Dpto. Sistemas

Einsa Multimedia, S.A.
Ctra. Campolongo a Monfero km 0,4 (Campolongo)
15614 Pontedeume (A Coruña)
España

http://www.einsamultimedia.com
Tlf: +34 981 454 015
Fax: +34 981 495 680

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*